# Kconfig - Bluetooth Mesh configuration options # # Copyright (c) 2017 Intel Corporation # # SPDX-License-Identifier: Apache-2.0 # menuconfig BT_MESH bool "Bluetooth Mesh support" select TINYCRYPT select TINYCRYPT_AES select TINYCRYPT_AES_CMAC help This option enables Bluetooth Mesh support. The specific features that are available may depend on other features that have been enabled in the stack, such as GATT support. if BT_MESH # Virtual option enabled whenever Generic Provisioning layer is needed config BT_MESH_PROV bool config BT_MESH_PB_ADV bool "Provisioning support using the advertising bearer (PB-ADV)" select BT_MESH_PROV default y help Enable this option to allow the device to be provisioned over the advertising bearer. if BT_CONN # Virtual option enabled whenever any Proxy protocol is needed config BT_MESH_PROXY bool config BT_MESH_PB_GATT bool "Provisioning support using GATT (PB-GATT)" select BT_MESH_PROXY select BT_MESH_PROV help Enable this option to allow the device to be provisioned over GATT. config BT_MESH_GATT_PROXY bool "GATT Proxy Service" select BT_MESH_PROXY help This option enables support for the Mesh GATT Proxy Service, i.e. the ability to act as a proxy between a Mesh GATT Client and a Mesh network. config BT_MESH_NODE_ID_TIMEOUT int "Node Identity advertising timeout" depends on BT_MESH_GATT_PROXY range 1 60 default 60 help This option determines for how long the local node advertises using Node Identity. The given value is in seconds. The specification limits this to 60 seconds, and implies that to be the appropriate value as well, so just leaving this as the default is the safest option. if BT_MESH_PROXY config BT_MESH_PROXY_FILTER_SIZE int "Maximum number of filter entries per Proxy Client" default 1 default 3 if BT_MESH_GATT_PROXY range 1 32767 help This option specifies how many Proxy Filter entries the local node supports. endif # BT_MESH_PROXY endif # BT_CONN config BT_MESH_SELF_TEST bool "Perform self-tests" help This option adds extra self-tests which are run every time mesh networking is initialized. config BT_MESH_IV_UPDATE_TEST bool "Test the IV Update Procedure" help This option removes the 96 hour limit of the IV Update Procedure and lets the state be changed at any time. config BT_MESH_SUBNET_COUNT int "Maximum number of mesh subnets per network" default 1 range 1 4096 help This option specifies how many subnets a Mesh network can participate in at the same time. config BT_MESH_APP_KEY_COUNT int "Maximum number of application keys per network" default 1 range 1 4096 help This option specifies how many application keys the device can store per network. config BT_MESH_MODEL_KEY_COUNT int "Maximum number of application keys per model" default 1 range 1 4096 help This option specifies how many application keys each model can at most be bound to. config BT_MESH_MODEL_GROUP_COUNT int "Maximum number of group address subscriptions per model" default 1 range 1 4096 help This option specifies how many group addresses each model can at most be subscribed to. config BT_MESH_LABEL_COUNT int "Maximum number of Label UUIDs used for Virtual Addresses" default 1 range 0 4096 help This option specifies how many Label UUIDs can be stored. config BT_MESH_CRPL int "Maximum capacity of the replay protection list" default 10 range 2 65535 help This options specifies the maximum capacity of the replay protection list. This option is similar to the network message cache size, but has a different purpose. config BT_MESH_MSG_CACHE_SIZE int "Network message cache size" default 10 range 2 65535 help Number of messages that are cached for the network. This helps prevent unnecessary decryption operations and unnecessary relays. This option is similar to the replay protection list, but has a different purpose. config BT_MESH_ADV_BUF_COUNT int "Number of advertising buffers" default 6 range 6 256 help Number of advertising buffers available. The transport layer reserves ADV_BUF_COUNT - 3 buffers for outgoing segments. The maximum outgoing SDU size is 12 times this number (out of which 4 or 8 bytes is used for the Transport Layer MIC). For example, 5 segments means the maximum SDU size is 60 bytes, which leaves 56 bytes for application layer data using a 4-byte MIC and 52 bytes using an 8-byte MIC. config BT_MESH_TX_SEG_MSG_COUNT int "Maximum number of simultaneous outgoing segmented messages" default 1 range 1 BT_MESH_ADV_BUF_COUNT help Maximum number of simultaneous outgoing multi-segment and/or reliable messages. config BT_MESH_RX_SEG_MSG_COUNT int "Maximum number of simultaneous incoming segmented messages" default 1 range 1 255 help Maximum number of simultaneous incoming multi-segment and/or reliable messages. config BT_MESH_RX_SDU_MAX int "Maximum incoming Upper Transport Access PDU length" default 384 range 36 384 help Maximum incoming Upper Transport Access PDU length. Leave this to the default value, unless you really need to optimize memory usage. config BT_MESH_RELAY bool "Relay support" help Support for acting as a Mesh Relay Node. config BT_MESH_LOW_POWER bool "Support for Low Power features" help Enable this option to be able to act as a Low Power Node. if BT_MESH_LOW_POWER config BT_MESH_LPN_ESTABLISHMENT bool "Perform Friendship establishment using low power" default y help Perform the Friendship establishment using low power, with the help of a reduced scan duty cycle. The downside of this is that the node may miss out on messages intended for it until it has successfully set up Friendship with a Friend node. config BT_MESH_LPN_AUTO bool "Automatically start looking for Friend nodes once provisioned" default y help Automatically enable LPN functionality once provisioned and start looking for Friend nodes. If this option is disabled LPN mode needs to be manually enabled by calling bt_mesh_lpn_set(true). config BT_MESH_LPN_AUTO_TIMEOUT int "Time from last received message before going to LPN mode" default 15 range 0 3600 depends on BT_MESH_LPN_AUTO help Time in seconds from the last received message, that the node will wait before starting to look for Friend nodes. config BT_MESH_LPN_RETRY_TIMEOUT int "Retry timeout for Friend requests" default 8 range 1 3600 help Time in seconds between Friend Requests, if a previous Friend Request did not receive any acceptable Friend Offers. config BT_MESH_LPN_RSSI_FACTOR int "RSSIFactor, used in the Friend Offer Delay calculation" range 0 3 default 0 help The contribution of the RSSI measured by the Friend node used in Friend Offer Delay calculations. 0 = 1, 1 = 1.5, 2 = 2, 3 = 2.5. config BT_MESH_LPN_RECV_WIN_FACTOR int "ReceiveWindowFactor, used in the Friend Offer Delay calculation" range 0 3 default 0 help The contribution of the supported Receive Window used in Friend Offer Delay calculations. 0 = 1, 1 = 1.5, 2 = 2, 3 = 2.5. config BT_MESH_LPN_MIN_QUEUE_SIZE int "Minimum size of acceptable friend queue (MinQueueSizeLog)" range 1 7 default 1 help The MinQueueSizeLog field is defined as log_2(N), where N is the minimum number of maximum size Lower Transport PDUs that the Friend node can store in its Friend Queue. As an example, MinQueueSizeLog value 1 gives N = 2, and value 7 gives N = 128. config BT_MESH_LPN_RECV_DELAY int "Receive delay requested by the local node" range 10 255 default 100 help The ReceiveDelay is the time between the Low Power node sending a request and listening for a response. This delay allows the Friend node time to prepare the response. The value is in units of milliseconds. config BT_MESH_LPN_POLL_TIMEOUT int "The value of the PollTimeout timer" range 10 244735 default 300 help PollTimeout timer is used to measure time between two consecutive requests sent by the Low Power node. If no requests are received by the Friend node before the PollTimeout timer expires, then the friendship is considered terminated. The value is in units of 100 milliseconds, so e.g. a value of 300 means 30 seconds. config BT_MESH_LPN_INIT_POLL_TIMEOUT int "The starting value of the PollTimeout timer" range 10 BT_MESH_LPN_POLL_TIMEOUT default BT_MESH_LPN_POLL_TIMEOUT help The initial value of the PollTimeout timer when Friendship gets established for the first time. After this the timeout will gradually grow toward the actual PollTimeout, doubling in value for each iteration. The value is in units of 100 milliseconds, so e.g. a value of 300 means 30 seconds. config BT_MESH_LPN_SCAN_LATENCY int "Latency for enabling scanning" range 0 50 default 10 help Latency in milliseconds that it takes to enable scanning. This is in practice how much time in advance before the Receive Window that scanning is requested to be enabled. config BT_MESH_LPN_GROUPS int "Number of groups the LPN can subscribe to" range 0 16384 default 8 help Maximum number of groups that the LPN can subscribe to. endif # BT_MESH_LOW_POWER config BT_MESH_FRIEND bool "Support for acting as a Friend Node" help Enable this option to be able to act as a Friend Node. if BT_MESH_FRIEND config BT_MESH_FRIEND_RECV_WIN int "Friend Receive Window" range 1 255 default 255 help Receive Window in milliseconds supported by the Friend node. config BT_MESH_FRIEND_QUEUE_SIZE int "Minimum number of buffers supported per Friend Queue" range 2 65536 default 16 help Minimum number of buffers available to be stored for each local Friend Queue. config BT_MESH_FRIEND_SUB_LIST_SIZE int "Friend Subscription List Size" range 0 1023 default 3 help Size of the Subscription List that can be supported by a Friend node for a Low Power node. config BT_MESH_FRIEND_LPN_COUNT int "Number of supported LPN nodes" range 1 1000 default 2 help Number of Low Power Nodes the Friend can have a Friendship with simultaneously. config BT_MESH_FRIEND_SEG_RX int "Number of incomplete segment lists per LPN" range 1 1000 default 1 help Number of incomplete segment lists that we track for each LPN that we are Friends for. In other words, this determines how many elements we can simultaneously be receiving segmented messages from when the messages are going into the Friend queue. endif # BT_MESH_FRIEND config BT_MESH_CFG_CLI bool "Support for Configuration Client Model" help Enable support for the configuration client model. config BT_MESH_HEALTH_CLI bool "Support for Health Client Model" help Enable support for the health client model. config BT_MESH_SHELL bool "Enable Bluetooth Mesh shell" select CONSOLE_SHELL depends on BT_MESH_CFG_CLI depends on BT_MESH_HEALTH_CLI help Activate shell module that provides Bluetooth Mesh commands to the console. config BT_MESH_DEBUG bool "Enable debug logs" depends on BT_DEBUG help Use this option to enable debug logs for the Bluetooth Mesh functionality. if BT_MESH_DEBUG config BT_MESH_DEBUG_USE_ID_ADDR bool "Use identity address for all advertising" help This option forces the usage of the local identity address for all advertising. This can be a help for debugging (analyzing traces), however it should never be enabled for a production build as it compromises the privacy of the device. config BT_MESH_DEBUG_NET bool "Network layer debug" help Use this option to enable Network layer debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_TRANS bool "Transport layer debug" help Use this option to enable Transport layer debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_BEACON bool "Beacon debug" help Use this option to enable Beacon-related debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_CRYPTO bool "Crypto debug" help Use this option to enable cryptographic debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_PROV bool "Provisioning debug" help Use this option to enable Provisioning debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_ACCESS bool "Access layer debug" help Use this option to enable Access layer and device composition related debug logs for Bluetooth Mesh. config BT_MESH_DEBUG_MODEL bool "Foundation model debug" help Use this option to enable debug logs for the Foundation Models. config BT_MESH_DEBUG_ADV bool "Advertising debug" help Use this option to enable advertising debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_LOW_POWER bool "Low Power debug" help Use this option to enable Low Power debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_FRIEND bool "Friend debug" help Use this option to enable Friend debug logs for the Bluetooth Mesh functionality. config BT_MESH_DEBUG_PROXY bool "Proxy debug" depends on BT_MESH_PROXY help Use this option to enable Proxy protocol debug logs. config BT_MESH_DEBUG_SETTINGS bool "Persistent settings debug" depends on BT_SETTINGS help Use this option to enable persistent settings debug logs. endif # BT_MESH_DEBUG endif # BT_MESH