# Kconfig - FSL FRDM K64F platform configuration options

#
# Copyright (c) 2014-2016 Wind River Systems, Inc.
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#

if SOC_FSL_FRDM_K64F
config SOC
	default fsl_frdm_k64f

config SRAM_BASE_ADDRESS
	default 0x20000000

config FLASH_BASE_ADDRESS
	default 0x00000000

config NUM_IRQ_PRIO_BITS
	int
	default 4

config NUM_IRQS
	int
	# must be >= the highest interrupt number used
	default 86

config SYS_CLOCK_HW_CYCLES_PER_SEC
	int
	default 120000000

config WDOG_INIT
	def_bool y
	# omit prompt to signify a "hidden" option
	help
	This processor enables the watchdog timer with a short timeout
	upon reset. Therefore, this requires that the watchdog be configured
	during reset handling.

config KERNEL_INIT_PRIORITY_DEFAULT
	default 40

config KERNEL_INIT_PRIORITY_DEVICE
	default 50

config UART_CONSOLE_PRIORITY
	default 60

if UART_K20

config UART_K20_PORT_0
	def_bool y

if UART_K20_PORT_0
config UART_K20_PORT_0_BASE_ADDR
	default 0x4006A000
config UART_K20_PORT_0_IRQ
	default 31
config UART_K20_PORT_0_IRQ_PRI
	default 3
config UART_K20_PORT_0_BAUD_RATE
	default 115200
config UART_K20_PORT_0_CLK_FREQ
	default 120000000
endif

config UART_K20_PORT_1
	def_bool y

if UART_K20_PORT_1
config UART_K20_PORT_1_BASE_ADDR
	default 0x4006B000
config UART_K20_PORT_1_IRQ
	default 33
config UART_K20_PORT_1_IRQ_PRI
	default 3
config UART_K20_PORT_1_BAUD_RATE
	default 115200
config UART_K20_PORT_1_CLK_FREQ
	default 120000000
endif

config UART_K20_PORT_2
	def_bool y
if UART_K20_PORT_2
config UART_K20_PORT_2_BASE_ADDR
	default 0x4006C000
config UART_K20_PORT_2_IRQ
	default 35
config UART_K20_PORT_2_IRQ_PRI
	default 3
config UART_K20_PORT_2_BAUD_RATE
	default 115200
config UART_K20_PORT_2_CLK_FREQ
	default 120000000
endif

config UART_K20_PORT_3
	def_bool y
if UART_K20_PORT_3
config UART_K20_PORT_3_BASE_ADDR
	default 0x4006D000
config UART_K20_PORT_3_IRQ
	default 37
config UART_K20_PORT_3_IRQ_PRI
	default 3
config UART_K20_PORT_3_BAUD_RATE
	default 115200
config UART_K20_PORT_3_CLK_FREQ
	default 120000000
endif

config UART_K20_PORT_4
	def_bool y
if UART_K20_PORT_4
config UART_K20_PORT_4_BASE_ADDR
	default 0x400EA000
config UART_K20_PORT_4_IRQ
	default 66
config UART_K20_PORT_4_IRQ_PRI
	default 3
config UART_K20_PORT_4_BAUD_RATE
	default 115200
config UART_K20_PORT_4_CLK_FREQ
	default 120000000
endif

endif # UART_K20

if UART_CONSOLE

config UART_CONSOLE_ON_DEV_NAME
	default "UART_0"

endif

if BLUETOOTH_UART

config BLUETOOTH_UART_ON_DEV_NAME
	default "UART_1"

endif

config GPIO
	def_bool y

config PINMUX
	def_bool y

config PWM
	def_bool n

if GPIO

config GPIO_K64
	def_bool y

config GPIO_K64_A
	def_bool y

config GPIO_K64_B
	def_bool y

config GPIO_K64_C
	def_bool y

config GPIO_K64_D
	def_bool y

config GPIO_K64_E
	def_bool y

endif

config GPIO_K64_A_BASE_ADDR
	default 0x400FF000

config PORT_K64_A_BASE_ADDR
	default 0x40049000

config GPIO_K64_B_BASE_ADDR
	default 0x400FF040

config PORT_K64_B_BASE_ADDR
	default 0x4004A000

config GPIO_K64_C_BASE_ADDR
	default 0x400FF080

config PORT_K64_C_BASE_ADDR
	default 0x4004B000

config GPIO_K64_D_BASE_ADDR
	default 0x400FF0C0

config PORT_K64_D_BASE_ADDR
	default 0x4004C000

config GPIO_K64_E_BASE_ADDR
	default 0x400FF100

config PORT_K64_E_BASE_ADDR
	default 0x4004D000


if PINMUX

config PINMUX_K64
	def_bool y
config PINMUX_BASE
	default 0x00000000
config PINMUX_NUM_PINS
	default 160
config PINMUX_K64_GPIO_A_NAME
	default GPIO_K64_A_DEV_NAME
config PINMUX_K64_GPIO_B_NAME
	default GPIO_K64_B_DEV_NAME
config PINMUX_K64_GPIO_C_NAME
	default GPIO_K64_C_DEV_NAME
config PINMUX_K64_GPIO_D_NAME
	default GPIO_K64_D_DEV_NAME
config PINMUX_K64_GPIO_E_NAME
	default GPIO_K64_E_DEV_NAME

config PRESERVE_JTAG_IO_PINS
	bool "Freescale FRDM-K64F JTAG pin usage"
	depends on PINMUX
	default y
	help
	The FRDM-K64F board routes the PTA0/1/2 pins as JTAG/SWD signals that
	are used for the OpenSDAv2 debug interface.  These pins are also routed to
	the Arduino header as D8, D3 and D5, respectively.
	Enable this option to preserve these pins for the debug interface.

endif #PINMUX

if PWM
config PWM_K64_FTM
	def_bool y
config PWM_K64_FTM_0
	def_bool y
endif

endif