The Pico 2W board is similar to the Pico 2 apart from the addition of an
Infineon Wifi chip.
This commit is based on the Pico and Pico W setup.
A different sample application is shown as blinky is not yet supported
on the Pico 2W.
Signed-off-by: Magpie Embedded <magpieembedded@gmail.com>
This file is not referenced anywhere, and the operating systems that
would require it are EOL. Remove it from the tree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The nPM1300 datasheet featured wrong soft start current values which
were also used in the DTS bindings for its regulator driver. This fixes
the values aligning them with the next release of the document.
Signed-off-by: Sergei Ovchinnikov <sergei.ovchinnikov@nordicsemi.no>
The MWDT linker has a specific input section sorting mechanism,
designated as x$y. Some prebuilt ARC libraries actually use it,
causing a lot of warnings when the linker decides where to place
their symbols. Provide explicit instructions in the linker script
instead of making the linker guess.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
Introduce the ACE 4.0 architecture, along with support for the NVL and
NVL-S platforms within the Intel ADSP framework in the Zephyr project.
This update includes:
- Addition of ACE 4.0 architecture configurations in Kconfig and
Kconfig.intel_adsp.
- Inclusion of device tree source files for NVL and NVL-S platforms,
defining CPU, memory, and peripheral configurations.
- Updates to driver files to support ACE 4.0 specific features,
including DMIC and SSP configurations.
- Introduction of new header files for ACE 4.0, detailing boot,
interrupt, IPC, power, and shim functionalities.
- Modifications to the CMakeLists.txt to include ACE 4.0 MMU support.
- Addition of default configurations for NVL and NVL-S platforms in
Kconfig.defconfig.ace40.
The NVL and NVL-S platforms are part of the Nova Lake series, targeting
advanced audio processing capabilities. ACE 4.0 introduces enhanced DSP
capabilities and advanced power management features, improving audio
stream handling and synchronization compared to ACE 3.0.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Serhiy Katsyuba <serhiy.katsyuba@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
When the kso[17:16] lines are enabled and `CONFIG_ASSERT` is
configured, the following error occurs: "Input cannot be
enabled for 'Open Drain', 'Open Source' modes without Output."
To address this, this commit configures kso16 and kso17 as
gpio output before applying the pinctrl settings.
Tested with: no abnormal keyscan occurs during
initialization
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
To reduce power consumption, the SPI clock is gated when no spi
transaction is in progress. With this mechanism, current
consumption is reduced by approximately 0.1mA when cpu idle.
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
This commit removes gpio-based cs support as it8xxx2 spi
only supports transactions using the dedicated cs pin.
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
If LVGL uses a work queue thread, we can't call LVGL functions from the
main thread. Use a k_event variable to signal between threads.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add helper functions that can be used to lock/unlock the LVGL's internal
mutex before calling API funcions.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Commit f499ea0 made it so that the compiler optimization flags are also
passed to the assembler. However, this breaks for the IAR toolchain
since it uses the GNU assembler which does not have the same
optimization flags as the IAR compiler.
This commit separates the compiler and assembler optimizations to make
it possible to specify appropriate flags in a toolchains corresponding
`compiler_flags.cmake`
Signed-off-by: Daniel Flodin <daniel.flodin@iar.com>
Added ABB analog status lock read retries if needed.
After cpu idle ABB macro may need some time to initialize
and report status locked. Attempts cound can be configured
using Kconfig option.
Signed-off-by: Łukasz Stępnicki <lukasz.stepnicki@nordicsemi.no>
added Real-Time Clock driver support for Texas Instruments
MSPM0 Family, currently this driver supports rtc time keeping
and calendar alarms functionality
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
This commit to initial support dts SoC layer on RX261
Signed-off-by: Hau Ho <hau.ho.xc@bp.renesas.com>
Signed-off-by: Phi Tran <phi.tran.jg@bp.renesas.com>
This commit brings a shell command to retreive the following application
version information:
- APP_VERSION_STRING
- APP_VERSION_EXTENDED_STRING
- APP_BUILD_VERSION
Signed-off-by: Alex Fabre <alex.fabre@rtone.fr>
A recent change triggered a warning in LLVM that was promoted to error
when run with twister.
```shell
goep.c:102:3: error: label followed by a declaration is a C23 extension
[-Werror,-Wc23-extensions]
102 | int err;
```
Add a scope to the switch case so that the declaration has proper scope.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
A recent change caused tests to start failing for qemu_x86_tiny/atom .
Similarly to bda38f033a, reduce the number of
reserved pages so that the test suite can pass for this platform.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Use HAL functions, which also wait for reset to complete.
Remove unused register size and active-low DT props.
Signed-off-by: Dmitrii Sharshakov <d3dx12.xx@gmail.com>
After the #93703 PR was merged we get a possibility to remove _node field
from bt_conn_cb struct if the BT_CONN_DYNAMIC_CALLBACKS option is disabled.
The list conn_cbs can also be safely removed by more macro usage.
Signed-off-by: Radosław Koppel <r.koppel@k-el.com>
CONFIG_BT_CTLR_DATA_LENGTH_MAX should set its default value up to
and including the maximum value supported by the Bluetooth spec
(251 bytes).
Signed-off-by: Sam Friedman <sam@golioth.io>
In most circumstances, GPIO pins identified in devicetree are
assigned to the SIO function at initialization. However, there
are cases where pin assignments change in alternate pinctrl
configurations. This commit adds the necessary definitions to
specify GPIO opration in pinctrl.
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Respect the newly introduced CONFIG_CAN_SAMPLE_POINT_MARGIN Kconfig option
when verifying if timing can be met.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add a Kconfig option for setting the maximum acceptable deviation in sample
point location (permille).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Clarify that the uart "attach commands" can be really anything
the shell can run.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Let's better refer to the board by the name "native_sim",
and leave the "native simulator" for the underlaying common
component which is shared with the nrf*bsim targets.
native_sim is the "plain vanilla" native simulator build with
some trivial HW models.
While the nrf*bsim targets use the native simulator (without those
trivial HW models), and expand it with the Nordic HW models.
Hopefully that helps people understand what is common and what
is not.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Let's update this west module/project collaborators:
wopu-ot & thoh-ot have been out of the picture for these HW models for
quite a while now, while rugeGerritsen has been much more active.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
