Enable RTC_ALARM and RTC_CALIBRATION in rtc_api tests for stm32h7s*
based ST boards: stm32h7s78_dk and nucleo_h7s3l8.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
(cherry picked from commit 0b3b601e75)
Add missing SoC overlay with UART1 loopback pin
configuration and add esp32c5_devkitc to the
platform_allow list.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
(cherry picked from commit 401b45abee)
Second clock_control_on() may return 0 or -EALREADY when the clock is
already on; assert it stays ON. Prepares for ESP32 clock_control
returning success when already enabled.
Signed-off-by: Anand Kumar <anandvtu16158@gmail.com>
Test was skipped if baudrate was too high. Test can actually
reconfigure the DUT device to use lower baudrate and run the test.
Initial baudrate is restored once test is completed.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Extend the most basic test (single read) to check supported data
bits sizes (5-8 bits). If driver does not support given configuration
then test is skipped.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Configure the GPT (General Purpose Timer) instances to use "free-run"
mode in the counter basic API test overlays for NXP i.MX RT and i.MX 8
boards. This ensures consistent timer behavior across the test suite.
Changes apply to:
- mimxrt1170_evk (GPT2-6)
- mimxrt1180_evk cm33 and cm7 (GPT2)
- imx8mp_evk, imx8mn_evk, imx8mm_evk (GPT1)
Signed-off-by: Felix Wang <fei.wang_3@nxp.com>
Avoid initialization failure by Updating channel information
to match the <dac1 1> configuration.
Also reduce ADC resolution to 10 bits to prevents the test from failing
due to ADC sampling value being outside the valid range.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
Necessary setup for doing SPI loopback testing on MAX32690EVKIT RV32 core,
to verify that peripheral on the secondary core.
Signed-off-by: Pete Johanson <pete.johanson@analog.com>
We fixed oversight that did not update the compatible in the
SPI loopback driver test for Microchip MEC174x/5x boards when
the SPI driver was last updated.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This PR removes duplicate properties in the same closure. The last
instance is the one the is keept.
This PR only cleans up current instances a separate PR will be done to
update the dts-linter to enforce this in the compliance check.
Signed-off-by: Kyle Bonnici <kylebonnici@hotmail.com>
Add flash to the supported feature list for versalnet_rpu and introduce
a board overlay to enable running flash common tests.
Signed-off-by: Srikanth Boyapally <srikanth.boyapally@amd.com>
Reduce CONFIG_TEST_WDT_SLEEP_TIME for drivers.watchdog.reset_none_ewm.
This aligns the feed interval with the current MCXW7x tick timing and
keeps the reset_none_ewm testcase within the effective EWM feed
Signed-off-by: Yves Wang <zhengjia.wang@nxp.com>
This fixes an issue that causes all SPI tests run natively on the
nRF54LM20-DK to fail. Furthermore, this adds a clarification in the
README.txt so that this test intention is clear about being run on only one
device, and not two.
Signed-off-by: Tyler Joseph Huffman <tyler@tylerh.org>
Add the Nucleo-C5A3ZG to the testcase.yml file so that the IWDG and WWDG
are can be tested daily.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
This reverts commit 6029af2dfce1b42e4a6d6741600dd0e28a357701.
Sleep pinctrl groups won't be used any longer for Espressif chips.
Strategy to switch pins to low power mode is enabled using hardware
feature.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Add test cases for the newly introduced pixel formats in the display
read/write test suite to ensure proper functionality:
- PIXEL_FORMAT_BGR_888: 24-bit BGR format with 8 bits per component
- PIXEL_FORMAT_ABGR_8888: 32-bit ABGR with alpha channel
- PIXEL_FORMAT_RGBA_8888: 32-bit RGBA with alpha channel
- PIXEL_FORMAT_BGRA_8888: 32-bit BGRA with alpha channel
Signed-off-by: Kate Wang <yumeng.wang@nxp.com>
Add an overlay to test SPI on Nucleo-C5A3ZG, and add the board to the list
of test cases.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Instead of disabling the PHY driver for the DWMAC test, use the GPIO
MDIO driver to allow testing the DWMAC driver with a PHY.
Signed-off-by: Tim Pambor <tim.pambor@codewrights.de>
Add a test for the FTL disk driver using the spi_nand flash driver. This
test utilizes the frdm_mcxn947 board with the MikroE Flash 5 Click shield.
Signed-off-by: Tim Pambor <tim.pambor@codewrights.de>
Add a test for the FTL disk driver using the spi_nand flash driver. This
test utilizes the frdm_mcxn947 board with the MikroE Flash 5 Click shield.
Signed-off-by: Tim Pambor <tim.pambor@codewrights.de>
- Add a board-specific devicetree overlay
to support the GPIO basic API test.
Signed-off-by: Deepika R <deepika@aerlync.com>
Signed-off-by: Sayooj K Karun <sayooj@aerlync.com>
- Add a board-specific devicetree overlay to enable
the PWM API test suite.
Signed-off-by: Surya Prakash T <suryat@aerlync.com>
Signed-off-by: Sayooj K Karun <sayooj@aerlync.com>
Default disable dac1 and fdcan3 nodes in stm32h5f5j_dk board since they
respectively conflict with the pin muxing for spi1 and adc3.
Add a board overlay file for DAC driver tests and samples to enable
dac1 and disable spi1.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Add a test for injected channels. The test first starts a regular
asynchronous sampling of several channels, then starts an injected
sampling. The test checks that both the regular and injected samplings
run without issues.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Change macro STM32_HSE_CSS to be defined (to 1) only when HSE clock
security system is enabled, as stated by the HSE DT node css-enabled
property. Consequently only use #ifdef STM32_HSE_CSS (or #if defined())
and IS_ENABLED(STM32_HSE_CSS) to test whether or not it's enabled.
No functional change but may prevent build warnings since prior
this change was STM32_HSE_CSS value tested while the macro may
not be defined.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Generalize the Hynitron CST816S touchscreen driver to support the
broader CST8xx controller family.
Changes include:
- Renaming the driver from input_cst816s.c to input_cst8xx.c
- Renaming drivers/input/Kconfig.cst816s to drivers/input/Kconfig.cst8xx
- Updating the Devicetree compatible from hynitron,cst816s to
hynitron,cst8xx
- Updating the Devicetree binding description and compatible field
- Updating board DTS files and test overlays to use the new compatible
These changes align the driver, Devicetree bindings, and compatible
strings with the actual hardware support, which covers the CST8xx
family rather than only the CST816S variant.
Signed-off-by: Muhammad Waleed Badar <walid.badar@gmail.com>
Remove stm32n6570_dk platform from this scenario as apb1-prescaler
is a constant(=1) and can't be set as defined in stm32_wwdg.overlay.
This causes a build issue.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
PR 104896 enforces the usage of the watchdog0 alias.
To avoid unwanted behaviors or settings for this test, remove
the other redundant if condition on watchdogs.
To avoid build compilation failures in CI related to WDT_TEST_MAX_WINDOW
redefinition for platforms other than STM32, move the existing condition
about st_stm32_window_watchdog outside the condition about the watchdog0
node.
These changes fix regressions encountered on several boards.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
- m33/m55: update overlay for gpio_basic_api test
- Change is intended to make wiring match pin usage of other
kit_pse84_ai testing support
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
- add spi to board's .yaml supported section for m33 and m55
- match spi testing support to kit_pse84_eval
- m33/m55: tests/.../spi_loopback
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
- add adc to board's .yaml supported section for m55
- Given ADC support shared with kit_pse84_eval, only the m55 is
supported for kit_pse84_ai
- m55: samples/.../adc_dt
- m55: tests/.../adc_api
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
