- Add ``R_BSP_SecondaryCoreStart`` for the primary core to start
the secondary core
- Disable ``clock_init`` for the secondary core
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Add support for clock subsystem configuration and pinctrl in the
DesignWare I3C driver to enable proper clock control and pin
management on platforms that require them.
Changes include:
- Add clock_subsys field to dw_i3c_config structure.
- Update clock_control_get_rate() and clock_control_on() calls to use
the configured clock subsystem instead of NULL.
- Use COND_CODE_1 with DT_INST_PHA_HAS_CELL to conditionally extract
clock subsystem ID from devicetree, providing backward compatibility
for platforms without clkid cell.
- Include pinctrl-device.yaml in devicetree binding to enable pinctrl
support for platforms that need pin configuration.
- Gracefully fallback to NULL behavior when clkid is not specified.
This follows the same pattern used by other I3C drivers (mcux, renesas_ra)
and enables proper clock management for SoCs that require clock subsystem
identifiers while maintaining compatibility with existing devicetree
configurations.
Signed-off-by: Shreehari HK <shreehari.hk@alifsemi.com>
The I2C target implementation for i2c_dw does not follow the
zephyr target specification. The following three issues are corrected:
1) The read_requested CB is called on every byte of the transaction
- it must be called only on the first byte of the transaction
2) The read_processed CB is called on every byte of the transaction
- it must be called only on bytes following the first byte
3) Bytes returned in the data ptr param of read_processed are not
sent to the controller
-These bytes must be sent to the controller
Signed-off-by: James Growden <jgrowden@tenstorrent.com>
CONFIG_FLASH_SIZE and CONFIG_FLASH_BASE_ADDRESS symbols were not defined in
native_sim even though it has a flash controller and flash defined.
Signed-off-by: Flavio Ceolin <flavio@hubble.com>
Use DRAM region 1 as the default spill area for the `.noinit`
section if appcpu is not present
Signed-off-by: Muhammad Waleed Badar <walid.badar@gmail.com>
Extra Zephyr modules can be provided via the EXTRA_ZEPHYR_MODULES CMake
list variable. Previously, if this variable were set in multiple places
(e.g. local CMake variable, cache variable set via -D, environment
variable), Zephyr will pick one source based on zephyr_get's documented
hierarchy and ignore the others.
Add the MERGE keyword when EXTRA_ZEPHYR_MODULES is read so that the list
of Zephyr modules is merged from all sources if this variable is set in
multiple places.
An example where this can be useful is when integrating additional Zephyr
modules with a vendor's Zephyr-based application whose build system already
contains usage of EXTRA_ZEPHYR_MODULES.
Signed-off-by: Kesavan Yogeswaran <hikes@google.com>
This board is actually meant to be used as a debug probe and has
dedicated connectors for DP and target UART, add an overlay to make both
work on the dap sample.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This is a follow-up to commit cafa288197.
Bit masks should use the bitwise OR operator, not the logical one...
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fix SHA256 verification failures on Windows by ensuring consistent
line ending handling in patch files. Replace inline hash calculation
with existing get_file_sha256sum() function and modify it to read
files as text with normalized line endings before encoding to UTF-8
for hashing.
This ensures cross-platform compatibility and prevents patch
integrity check failures due to CRLF/LF differences between
operating systems.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
add range of cpu power states (run/sleep, stop and standby) for MSPM0
series. add exit latencies ranging from 1.5-15.7µs and minimum
residency times of 5-10ms for optimal power management transitions.
Signed-off-by: Sanjay Vallimanalan <sanjay@linumiz.com>
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
The fast wake feature in the MSPM0 GPIO peripheral allows the GPIO module
to stay in a low-power state and detect interrupt events on the device pins
without requiring a high-speed clock. This allows the device to support
fast wakeup from low-power modes, such as STOP and STANDBY, on any GPIO
pin.
Signed-off-by: Sanjay Vallimanalan <sanjay@linumiz.com>
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
add support for SHUTDOWN operating mode in TI MSPM0 series for power-off
operation. Uses HWINFO for reset cause detection to handle shutdown IO
release on low power wakeup.
Signed-off-by: Sanjay Vallimanalan <sanjay@linumiz.com>
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
TI MSPM0 series supports range of power modes (RUN/SLEEP, STOP, STANDBY)
supporting low power operations. Provides automatic restoration to
RUN mode on wakeup from any low power state.
Signed-off-by: Sanjay Vallimanalan <sanjay@linumiz.com>
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Update hal_ti to include input-enable property for all UART RX pins.
Without the input-enable property, UART reception does not function
correctly when the SoC enters low-power mode. Adding this property
ensures reliable UART operation in all power states.
Signed-off-by: Sanjay Vallimanalan <sanjay@linumiz.com>
Add support for custom NRFX_DIR for Sysbuild builds by checking if
NRFX_DIR has been defined in Sysbuild.
Signed-off-by: Michał Bainczyk <michal.bainczyk@nordicsemi.no>
This helps to circumvent issues in current BAP implementation when
multiple streams are present. Also puts RX path in line with
configuration of TX path.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Extend vpr_launcher and device tree bindings to support configuring
the DMA secure attribute.
Signed-off-by: Dhanoo Surasarang <dhanoo.surasarang@nordicsemi.no>
Other targets that define this symbol do it in the Kconfig file, and
gate it with a SOC_ model or series symbol. Defining a default in the
Kconfig.soc instead applies it on every build, which is not desired.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Add support for halting the Radio core immediately after reset. This
ensures that a debugger can attach and take control from the very
first instruction.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
PM on the nrf54h20 has minimal utility if power domains and devices
are not managed at runtime, as these prevent the soc from entering
sleep states in the first place. Enable PM_DEVICE by default if PM,
which in turn enables PM_DEVICE_RUNTIME for devices and power
domains.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Remove wakeup trigger from Series 2 boards. The implementation
seems to configure a GPIO to be driven low on boot, which has
nothing to do with wakeup. In order to actually configure a
wakeup GPIO, the GPIO_INT_WAKEUP flag would need to be used when
registering an interrupt on the pin. However, this should not
be the responsibility of the board. It is an application
concern, so remove it from the boards.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Use both cores for Zephyr by default. I did enable SMP, however forgot
to enable PSCI to turn on the other cores in the initial PR.
Tested with samples: `tests/arch/arm64/arm64_psci/` and
`samples/arch/smp/pi`
Requires [0].
[0]: https://github.com/zephyrproject-rtos/zephyr/pull/95325
Signed-off-by: Ayush Singh <ayush@beagleboard.org>
Print return code on error and remove logging in `sntp_resync_handler`
since it calls `net_init_clock_via_sntp` which already does logging.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add test case where TDM is tested with 8 channels,
32 bit word size and 48k sample rate.
Add Kconfig that enables test skip if the driver supports
8 channels but fails in this configuration.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Expand the test case for RTIO_OP_AWAIT to also cover the relaxed variant
where just the SQE chain is paused until completion, and the rtio_iodev
can serve unrelated SQEs meanwhile.
Signed-off-by: Emil Dahl Juhl <emil@s16s.ai>
Allow the rtio executor to handle the RTIO_OP_AWAIT for cases where no
rtio_iodev needs to be blocked while waiting for the signal.
When the RTIO_OP_AWAIT was introduced, the highlighted usecase was
performing transactions within an exact time window. This can be
achieved by blocking the rtio_iodev, effectively locking the bus, while
awaiting.
However, a relaxed implementation which doesn't block any rtio_iodev is
really useful for device drivers that use some kind of ready-event
during transactions. For example in order to read configuration out of
a sensor, the following flow may be required:
1. Write some cmd like "read accelerometer scale"
2. Await data-ready GPIO rising edge (might take "a long time")
3. Read the requested data payload from the sensor
Using a relaxed variant of the RTIO_OP_AWAIT this can be elegantly put
together in a single chained rtio sequence. And by not blocking the
rtio_iodev, other devices can be operated during the await period.
Of course, not blocking the rtio_iodev also means that the bus may be
busy when the RTIO_OP_AWAIT completes and thus, step 3 may be blocked
for a some time and the guarantee of an exact time window cannot be
achieved with the relaxed variant.
To make the API clearer, separate helpers are added for the strict
(blocking iodev) and relaxed (blocking only the sqe chain) variant
respectively.
Signed-off-by: Emil Dahl Juhl <emil@s16s.ai>
* Adds overlay files for tests/drivers/pwm/pwm_api and
tests/drivers/pwm/pwm_gpio_loopback to run these tests on the
cyw920829 board.
Signed-off-by: Bill Waters <bill.waters@infineon.com>
* Updates the overlay files for samples/basic/blinky_pwm and
samples/basic/fade_led to run on the cyw920829m2_evk board.
Signed-off-by: Bill Waters <bill.waters@infineon.com>
This change makes improvements and bug fixes for the Infineon PWM
driver. These include:
* Removes hard coded register addresss from driver.
* Addresses issues causing pwm_api and pwm_gpio_loopback tests to
fail, as well as functional failures.
* Restructures device tree file to better represent the hardware
architecture of the tcpwm module.
* Allows configuration of hardware behavior when PWM is disabled.
Signed-off-by: Bill Waters <bill.waters@infineon.com>
* Changes driver naming to reflect hardware IP being used (TCPWM)
instead of referencing cat1. Cat1 is an internal infineon
reference which has little meaning to users and is being phased
phased out.
Signed-off-by: Bill Waters <bill.waters@infineon.com>
This commit introduces the FoBE Quill nRF52840 Mesh board configuration,
including device tree files, Kconfig settings, and necessary
documentation. It also adds GPIO header definitions
and updates vendor prefixes for proper identification.
Signed-off-by: Chiho Sin <chihosin@icloud.com>
