Move and rephrase the comment to better explain reason why obtained
IRQ number is decremented.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Add PM action for the NXP LCDIC driver so that we can
recover from a lower power mode where we lose the register
settings and we need to reconfigure the block.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Commit 857e5793f1 fix
the flash_mcux_flexspi_nor.c driver to wait for the
FlexSPI to be idle before performing write/erase
operations. Add a similar check to these drivers that
also use the FlexSPI NOR block.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add support for transmitting using the asynchronous API. The
asynchronous portion is simulated through a dedicated polling thread.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add support for transmitting using the asynchronous API. The
asynchronous portion is simulated through the system workqueue.
Signed-off-by: Jordan Yates <jordan@embeint.com>
move phy_link_callback_set() to the iface init,
so we don't have to manually check the link state,
as phy_link_callback_set() will also invoke the callback.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Add a simple non-XIP transaction before deactivating the QSPI after
a XIP transaction is performed. This prevents a CPU hang from occuring
when another XIP transaction is attempted after the QSPI is activated
again.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Increased the heap mempool size for the socketpairs. This way there will
be enough memory available to allocate 2 * struct spair.
Signed-off-by: Ibe Van de Veire <ibe.vandeveire@basalte.be>
Moved target dependent startup time from header file to
Kconfig option to allow adding new targets with new .conf
file rather that modyfing source of the test. Adjusted
startup time for nRF54L09 and nRF54L20.
Signed-off-by: Michał Stasiak <michal.stasiak@nordicsemi.no>
When applying the connection parameter update, the window widening
for the previous connection interval was not applied since that is
normally done in LLL
Fixed by applying the window widening in ull_conn_update_parameters()
instead in this case
Fixes EBQ test failure in LL/CON/PER/BV-10-C
Signed-off-by: Troels Nilsson <trnn@demant.com>
Disable GPD for MCUBoot build, as it cannot be
reinitialized later in application (SDFW does not
support reinitialization).
Also, remove the GPD disabling from the mcumgr sample
for nRF54H20 iron board app - it was the reinitialization
that caused problems.
Signed-off-by: Michal Kozikowski <michal.kozikowski@nordicsemi.no>
Make sure RS process is stopped if network interface goes down
as there is no point doing it any more.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
It might happen that if the network interface is going up/down
fast enough, the RS timer could get inserted to the active RS
timer list twice. This would then cause a forever loop in
rs_timeout() when traversing the active list.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Commit extends the communication test between the LPN and
the third mesh device by checking that LPN and the third mesh
device can exchange data normally after friendship termination.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
MAX31855 driver had a wrong position of sign bits causing
invalid reading of negative temperature values. Fixed by
shifting position of sign bit by one bit.
Signed-off-by: Petr Vilím <petr.vilim@proton.me>
Streaming mode now supported through In-band Interrupts (I3C).
By default, a dedicated INT GPIO is prioritized, even if the sensor
is on an I3C bus.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
I3C is now a bus supported, by relying on RTIO IODEV which is supported
for all buses (I2C, I3C and SPI). Tested backwards compatibility: I2C
and I3C.
No IBI support yet.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Add clock control support for RZ/A2M
Signed-off-by: Hoang Nguyen <hoang.nguyen.jx@bp.renesas.com>
Signed-off-by: Binh Nguyen <binh.nguyen.xw@renesas.com>
