When reading and printing hosname or domain name from DHCP options, we need
to skip the leftover bytes that do not fit into the provided buffers.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Coverity is reporting a possible untrusted loop bound, caused by accessing
num_pins through a tainted pointer. Use explicit type cast to keep coverity
happy.
CID: 347195
Signed-off-by: Loic Domaigne <tech@domaigne.com>
Drop few CONFIG_PM_DEVICE_RUNTIME guards, the pm_device_runtime
functions they are masking are no-op automatically when the
corresponding config option is not selected.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Current code only calls pm_device_runtime_get when registering target
devices if the device is marked as wakeup capable by the application.
This does quite work for a setup with PM=n and PM_DEVICE=y and
PM_DEVICE_RUNTIME=y, where the CPU does not really go in stop mode ever,
and results in the i2c target device not working at all.
Fix this by always claiming the device when PM_DEVICE_RUNTIME is
enabled.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix an issue where calling gpio_pin_interrupt_configure
with edge mode and later calling it with level mode, did
not release the allocated gpiote channel.
Repeating the above sequence caused us to run out of
gpiote channels.
Signed-off-by: Markus Lassila <markus.lassila@nordicsemi.no>
The TIMER has 3 PWM channels, allowing all 3 RGB leds to be
controlled by the same PWM controller instance.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Add PWM driver for the Timer peripheral on Series 2.
The TIMER uses the high-frequency EM01 Group A clock, and has
a 16- or 32-bit counter. It supports PWM period and pulse capture
on channel 0, and PWM output on all channels.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Add PWM driver for the Low Energy Timer peripheral on Series 2.
The LETIMER runs at up to 32 kHz and has a 24-bit counter. It
only supports PWM output, it does not support input capture.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Use LOG_ERR() instead of LOG_DBG() in flash_fill() when this function
fails to perform the write operation, so that the failure is better
visible and its cause is easier to identify.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When no flash device requires erase, this test does not retrieve
flash page size with flash_get_page_info_by_offs(), but instead
it takes an arbitrary page size based on the test area length.
Since the test_flash_copy routine needs to use two pages, the test
area needs to be split into at least two parts. Correct the related
code and add a check if test_flash_copy requirements are met.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Implement NXP-specific support for the remote processor
resource table, including custom definitions and initialization
logic to meet NXP's communication requirements.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Modify the build system to conditionally compile
vendor-specific resource table support based on configuration.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Introduce macros to define initialization
routines for OpenAMP resource table entries.
This will allow to extend the default OpenAMP
resource table with vendor-specific data structures.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Enhance flexibility by allowing vendors to define their own
resource tables. This is achieved by moving the vdev and vring
functions into the source file, requiring each vendor to
implement these functions within their specific resource
table definitions.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Switching to void allows greater flexibility in supporting
vendor-specific resource tables.
This change reverts commit 39863b66bd, and adds some fixes.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Use new docker with SDK 0.17.2.
SDK 0.17.2 has a new Qemu with improved support for RX architecture.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Seperate the ``ethos_u_common`` for every vendor and
``ethos_u_arm`` for sepcific Arm's boards. Enable vendors
to self-configure the init flow and IRQ handler.
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
- Update to use ETHOS_U config instead of ARM_ETHOS_U
- Update prefix ETHOS_U_ for all configs that use ARM_ETHOS_U_
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Add UART test overlays for Nucleo U385RG-Q board.
Remove non serial boot conf file since they are now unnecessary.
Signed-off-by: Khaoula Bidani <khaoula.bidani-ext@st.com>
The bq27xx driver incorrectly uses the 'val' variable in a switch()
statement that should operate on 'chem_id'. This leads to incorrect
behavior for fuel gauges such as the BQ27427, where the chemical ID
determines how properties are interpreted.
This commit replaces 'switch(val)' with 'switch(chem_id)' to ensure
proper handling of fuel gauge behavior across supported devices.
Signed-off-by: Oleksii Shcherbyna <oleksii.shcherbyna@droid-technologies.com>
Disable testing second QDEC instance until the issue with multiple
QDEC instances support is resolved
Signed-off-by: Bartosz Miller <bartosz.miller@nordicsemi.no>
