remove the use of phy_configure_link() in the ethernet drivers.
The user can now select the default speeds via DT prop, doing
another phy_configure_link() in the eth driver would overwrite
that.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
fixed link mode is a mode where we don't comunicate with the phy,
therefore we don't need it in other phys as the generic phy_mii one.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
move adi,adin1110.yaml adi,adin2111.yaml
from the phy subdir back into the ethernet dir.
They are ethernet controller bindings, not phy bindings.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
1. Supported ACMP case on mimxrt700_evk
2. Fixed the issue of using the same address for
different trigger sources. This bug would cause the
examples to run in a way that did not match the theory.
3. Removed some redundant descriptions in the README.rst.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
1. Fixed the bug that DAC value was set incorrectly.
2. The MIMXRT700 does not have windowed mode and
'enableSample' controls, code added for compatibility
on this platform.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
As packets need to be forwarded between Wi-Fi/Eth interface and
OpenThread interface, routing support has to be re-enabled and
configurable through prj.conf file.
Signed-off-by: Cristian Bulacu <cristian.bulacu@nxp.com>
Don't automatically enable device runtime PM on the SPI port just
because `PM_DEVICE_RUNTIME` is enabled. Require the user to explicitly
call `pm_device_runtime_enable` on the port, or add
`zephyr,pm-device-runtime-auto` to the devicetree node.
Through the usage of `pm_device_driver_init`, the default clock control
and pinctrl handling can all be contained in `spi_stm32_pm_action`.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Board overlay was moved from downstream to upstream.
By mistake, License was left unchanged.
Change License type to match with the upstream.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Board overlays were moved from downstream to upstream.
By mistake, License was left unchanged.
Change License type to match with the upstream.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Added a new 'Board variants' section to the board documentation
to describe supported flash and PSRAM configurations for Espressif
boards using snippet-based build-time selection.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Fix FS shell using fixed 'storage_partition' nodelabel instead of
accessing the DT defined partition from the zephyr,fstab,littlefs
node partition property.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
This commit adds config_get support for native_tty. This is helpful as
some driver code (e.g. u_blox m8) will error out if they can't read the
current configuration.
Signed-off-by: Vytautas Virvičius <vytautas@virvicius.dev>
Threads must not attempt to context switch if they are holding a spinlock.
Add this information to the documentation for k_spin_lock().
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Upon context switch, the virtual "interrupt lock" acquired by irq_lock()
must not be "held". However, the current documentation for irq_lock() says
that it is perfectly valid to hold it (!), and that a suspended thread will
hold the "interrupt lock" upon being scheduled again (!!).
Update the documentation to remove the outdated section and indicate that
context switching while holding the interrupt lock is not allowed.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The do_swap() routine used when CONFIG_USE_SWITCH=y asserts that caller
thread does not hold any spinlock when CONFIG_SPIN_VALIDATE is enabled.
However, there is no similar check in place when CONFIG_USE_SWITCH=n.
Copy this assertion in the USE_SWITCH=n implementation of z_swap_irqlock().
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This reverts commit 3e9dffbe25.
Though this works fine, when CONFIG_ASSERT=y the spinlock validation
fails as the underlying code though uses OSAL spinlock APIs is not ready
* sleeping with spinlock held
* multiple threads taking the same spinlock (might work on UP, but not
on SMP on the same CPU)
Revert this for now, till the underyling is robust.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
the nRF connect device tree extension shows below warning:
'Property not mentioned in "nordic,nrf-pinctrl:child"'.
Fix this by applying the property to both groups separately.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Image files for ADI shield boards were introduced in commit
25c7fa4e63, but they weren't referenced
anywhere in the documentation source and thus were deadstripped from the
build, resulting in broken image references in the board catalog card
view.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Also increase regulator init priority so that ethernet vdd is
turned before PHY initialization
Signed-off-by: Peter van der Perk <peter.vanderperk@nxp.com>
Re-use the workqueue instead of having dedicated thread for handling
interrupts. This reduces memory usage and complexity.
Furthermore adds an auto mode for 100BASE-T1 negotiation.
Signed-off-by: Peter van der Perk <peter.vanderperk@nxp.com>
The modem modules cmux module is currently directly coupled to the
presence of specific modems, rather than being selected by drivers
for whatever hardware wants to request the default MTU of 127 bytes.
This commit the makes the device drivers (for now, modem_cellular)
select the symbol, thus decoupling the modem modules from the
presence of any specific device.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Add declaration of the HSE and HSI frequency that will be used to compute
the SystemCoreClock.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Add declarations for High-Speed External (HSE) and High-Speed Internal
(HSI) clocks.
These clocks, based on oscillators, can be used to generate the system
clocks.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Add soc_early_init_hook() function to update the SystemCoreClock variable,
which represents the reference clock.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Use wrapper function for read operations to allow using the new HAL
function that handles ECC checks and erased page detection.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
