This commit is retrieving the config FLASH_BASE_ADDRESS
from the XSPI node of the stm32 device dtsi <reg> property of the
"st,stm32-xspi" node. For example the CONFIG_FLASH_BASE_ADDRESS
is 0x90000000 and application is linked for that address.
Size is given by the size property of the "st,stm32-xspi-nor" node.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When a LD sends an ic-msg to SCFW - it happens that sometimes that SCFW
does not handle the request.
For the moment the problem is solved by sending a second vevif event
shortly after the initial request.
Signed-off-by: Maciej Meijer <maciej.meijer@nordicsemi.no>
Add support for cc23x0 RTC driver in counter.
RTC is always ON after device boot. Timer is restared only
on POR, and is active during STANDBY and ACTIVE power states.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Add mcxw filter to catch changes to drivers/ieee802154/ieee802154_mcxw.c
Add George-Stefan as a collaborator for NXP Wireless
Signed-off-by: David Leach <david.leach@nxp.com>
Select the PLL clock source for PLL2 or PLL3 as well as main PLL
This choice is useful if main PLL is off (sysclock from fixed clock)
but PLL2 or PLL3 are on for other peripherals
All PLL must have the same source else this is an error.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add new device tree property specifying the number of
dummy-cycles required when reading the JEDEC ID.
The Arduino Opta has an at25sf128a with JEDEC ID 1F 89 01.
The PR below adds support for this, but the id read is 01 1F 89.
Changing DummyCycles to 16 causes the correct value to be read.
https://github.com/zephyrproject-rtos/zephyr/pull/89539
Signed-off-by: Mark O'Donovan <shiftee@posteo.net>
Nuvoton M55M1 series supports M-profile Vector Extension (MVE) (also
known as Arm Helium technology). This enables compute applications
such as DSP and machine learning.
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
Receive buffer must be aligned to word when
CONFIG_MODEM_BACKEND_UART_ASYNC_HWFC=y is set.
Signed-off-by: Markus Lassila <markus.lassila@nordicsemi.no>
Add the nxp,rtxxx-dsp-ctrl driver.
Responsibility of this driver is to load code executed by Xtensa-family
cores on NXP i.MX RTxxx microcontrollers and to control their run.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
In order to support working with multiple VIFs (e.g., STA + AP) add
interface as an option for all commands.
The interface can belong to same chipset or different (hypothetical).
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
According to wba55 refman RM0493, gpdma1 request for
spi1_rx_dma and spi1_tx_dma is 1 and 2.
solve failed test on drivers.spi.stm32_spi_dma.loopback
scenario.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
- enable spi3 and usart3 nodes for driver test purpose.
- delete usart1 node due to conflicting pins with i2c1
node
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
For the BAP broadcast sink sample handling of requested BIS sync set
to BT_BAP_BIS_SYNC_NO_PREF for one or more subgroups is now added.
In case of no preference of requested BIS then sync is adjusted to the
number of streams available when no target allocation present.
Signed-off-by: Jens Rehhoff Thomsen <jthm@demant.com>
Create Kconfig configuration for nrfx_clock driver and use that to export
configuration to nrfx via nrfx_kconfig. So far nrfx_kconfig was using
Kconfig flags from clock_control which created a fixed connection between
nrfx_clock and clock_control and nrfx_clock could not be used without
clock_control in Zephyr.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Useful to see what prefix is being selected for a given
IPv6 address if debugging is enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Always prefer preferred IPv6 address over deprecated one
regardless of prefix length. This works now same way as in
Linux.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Some SoCs generates unexpected RXTO event during restart.
Restart happens when ENDRX_STARTRX short is enabled and STOPRX
is triggered (via short or by CPU). STOPRX starts closing
procedure and ENDRX event is generated at some point which
triggers STARTRX and closing procedure is interrupted. RXTO
should not be triggered in that case. Due to internal timings
some SoC on fast UARTE instance will trigger RXTO followed
by RXSTARTED. This RXTO event shall be cleared as receiver is
actually restarted and not stopped.
Affected SoC is not in tree so Kconfig is added which enables
the workaround.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add initial support for TI MSPM0 UART with basic poll-in and poll-out
functionality.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Jackson Farley <j-farley@ti.com>
