IPPROTO_RAW is not a valid protocol type for AF_PACKET sockets, which
should only use IEEE 802.3 protocol numbers. Therefore remove support
for this type of sockets.
As an alternative, users can use AF_PACKET/SOCK_DGRAM or
AF_INET(6)/SOCK_RAW, depending on the actual use case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Introduce changes in the networking stack which allow to create raw IP
sockets, so that applications can send and receive raw IP datagrams.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Register connection type along with family and protocol, so that it's
possible to differentiate between connection listening for raw IP
datagrams and TCP/UDP/other packets.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
There is no need to wait on xfer_new and xfer_finished and therefore
atomic services can be used instead of events.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add minimal support for board Renesas RZ/G2L-SMARC
Signed-off-by: Tien Nguyen <tien.nguyen.zg@renesas.com>
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
Created new files and relocate hostapd support code in glue layer to new
files. The new files will be compiled only if hostapd support is enabled.
Signed-off-by: Hui Bai <hui.bai@nxp.com>
When endpoint is disabled while hibernated, the UDC endpoint state has
to be reset. Set the busy to false to keep UDC endpoint state in sync
with peripheral register state.
Fixes: 2be960ad2b ("drivers: udc_dwc2: Disable endpoint while
hibernated")
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Private node identity advertisements must stop immediately when
ordered by PTS. To do so; adding enabled parameter to
btp_priv_node_id_get_cmd.
Signed-off-by: alperen sener <alperen.sener@nordicsemi.no>
Private Node Identity advertisement on a subnet should stop as soon as
the network is removed.
Signed-off-by: alperen sener <alperen.sener@nordicsemi.no>
The datasheet erroneously suggested to add a + 1 to the abort len.
This was suggested because if a controller gave a EoD, then it was
afraid that the abort would take precedence over the EoD. This was
not true. The EoD will always take precedence over a controller
abort. Remove the + 1 as this can cause issues.
For example, when talking to a part that will auto-increment a read
address, having the +1 can unknownly move this address pointer further
than anticipated.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
It is most certainly 'okay' for a secondary controller to do a
ENTDAA. Remove the 'block' that was preventing this.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Add a workaround for NRF52 anomaly 78: "High current consumption when
using timer STOP task only". Use the SHUTDOWN task instead.
For consistency, CLEAR the timer timer after STOPPING on devices that
lack the SHUTDOWN task. This also aligns the behavior with
nrfx_timer_disable().
For devices with the SHUTDOWN task, this restores the behavior previous
to e92323f.
Fixes#87224
Signed-off-by: Marco Widmer <marco.widmer@bytesatwork.ch>
Fixes an issue where pinctrl psel properties encoded with
NRF_PSEL_DISCONNECTED() caused a build failure.
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
Add missing support for J-Link in board.cmake configuration
for Nucleo G4 boards so they can be
flashed and debugged using J-Link.
Signed-off-by: Kuba Gryglak <gryglak.kuba@protonmail.com>
doc: same54_xpro Fixed broken links in index
- Updated pdf link to datasheet
- Added html link to datasheet
- Added link to product page
- Updated zip file link
- Added zip file link to newer revision
Signed-off-by: Robert Perkel <robert.perkel@microchip.com>
The disparity in C objects built causes
the test to fail.
This removes those lines from the log
to inline log comparison.
Let's disable it in the relevant test.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
Replace uses of OVERLAY_CONFIG with EXTRA_CONF_FILE
to follow the rest of Zephyr where OVERLAY_CONFIG was
deprecated in favor of EXTRA_CONF_FILE.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
`nsos_connect_blocking()` is not returning the error as expected. It is
expected to return a negative `NSI_ERRNO_MID_...` value, but it is
returning a positive errno value. `nsos_connect_blocking()` should map
the errno value to a negative `NSI_ERRNO_MID_...`, which `nsos_connect()`
maps back to a -1 return with errno=`ECONNREFUSED`.
the current sequence of events:
- `ECONNREFUSED` occurs during connection
- `nsos_connect_blocking()` returns positive `ECONNREFUSED`
- `nsos_connect()` returns positive `ECONNREFUSED`
- `zsock_connect()` returns positive `ECONNREFUSED`
the expected sequence of events:
- `ECONNREFUSED` occurs during connection
- `nsos_connect_blocking()` returns negative `NSI_ERRNO_MID_ECONNREFUSED`
- `nsos_connect()` returns -1, errno=`ECONNREFUSED`
- `zsock_connect()` returns -1, errno=`ECONNREFUSED`
Signed-off-by: Noah Olson <noah@wavelynx.com>
Having the log level set at debug causes a message to be printed
every time a mailbox message is sent or received. If we log this
using the RPMSG shell, then each message sent generates another
message, causing an an infinite message loop.
Do not set the level to debug by default, allow the level to
be set by the config LOG_DEFAULT_LEVEL.
Signed-off-by: Andrew Davis <afd@ti.com>
If an option is set in the project default configuration it does not
need to be set again in a board specific configuration overlay. Remove
instances of this.
Signed-off-by: Andrew Davis <afd@ti.com>
