When we have coexistence of hostapd and wpa_supplicant,
wpa_msg has different implementation.
So to let them work together, we need to have common implementation
for wpa_msg and dispatch msgs for hostapd and wpa_supplicant.
So add register zephyr_hostap_ctrl_iface_msg_cb,
and judge if ctx is hostapd by the first integer where ctx points to.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
Hostapd has TODO in hostapd_dpp_handle_config_obj,
to save DPP connector using wpa_msg.
AP DPP needs to use dpp_connector, dpp_netaccesskey and dpp_csign
in DPP Peer Discovery handshake in hostapd_dpp_rx_peer_disc_req.
So add AP DPP wpa_msg event handler to store these info.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
Add hostapd mgmt ops, some use same api as wpa_supplicant,
and DPP use different ops.
supplicant_dpp_dispatch use wpa_cli and hapd_dpp_dispatch use hostapd_cli.
And use common DPP param parse.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
Add DDR variant of the i.MX95 EVK board (M7 core). Using this
variant, one can run Zephyr from DDR instead of ITCM/DTCM
as it's the case for the M7 "base" board.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This prevents an overlap with `storage_partition`
Additionally, it fixes the following warning:
> unit address and first address in 'reg' (0x20000) don't match for
> /soc/flash-controller@4001e000/flash@0/partitions/partition@19000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x60000) don't match for
> /qspi_flash@40890000/flash@60000000/partitions/storage_partition@70000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
For code clarity, this commit adjusts the use of `return` statements
in functions with a void return type as follows:
- Transform `return foo();` into separate statements:
`foo();`
`return;`
- Remove unnecessary `return` statements when
they don't affect control flow.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
By keeping track of run-time ATT MTU of all connected peers, it's
possible to increase the notification payload size; thus increasing
data-throughput sent over Bluetooth.
Note that this assumes the Bluetooth connection is properly configured
(with the corresponding connection parameters) to optimize performance.
This is application-specific and shall be examined on each scenario for
optimal performance.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Parts related to the thread runtime stats are somewhat
standalone, refactor it out instead of having two #ifdef
and two places.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Split the `kernel_service.c` into multiple subcommand files,
each file would register with the main `kernel` cmd based on
the dependencies in Kconfig/CMakeLists.txt.
This greatly reduces the number of precompiler directives.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Deadloop happens when CONFIG_NET_ROUTING and VLAN are enabled.
In function net_ipv6_prepare_for_send(), pkt->iface will be
updated with net_pkt_set_iface(pkt, iface) in 2 scenarios:
1. ip_hdr->dst is onlink
2. check_route or nbr_lookup
VLAN is virtual-iface which attaches to a physical-iface. Each
time a packet being sent to a VLAN port will invoke twice of
the net_send_data(). The 1st time, pkt->iface is set to virtual
iface and the 2nd time to physical iface.
However in above 2 scenarios, at the 2nd time of calling the
net_send_data(), the pkt-iface will be changed back to virtual
iface. The system runs into a deadloop. This can be proved by
enabling CONFIG_NET_ROUTING with the VLAN sample.
The main purpose for net_ipv6_prepare_for_send() is to set the
right ll_dst address. If the ll_dst address is already set, then
no need to go through it again. If the packet has done with the
forwarding and set the ll_dst, then no need to check_route again.
And, the pkt->iface will not be changed back to virtual iface.
Fixes: #77402
Signed-off-by: Shrek Wang <shrek.wang@nxp.com>
Increased variable to the mandatory amount of commands, since the
comment of SHELL_SUBCMD_ADD states
"Number of mandatory arguments including command name"
but net suspend takes the interface number to suspend
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
This commit removes the preposition "in" from the phrase
"in particularly"in the I2C and I3C Controller API sections
to improve readability.
Signed-off-by: Arrel Neumiller <rlneumiller@gmail.com>
This fixes the following kind of warnings:
> unit address and first address in 'reg' (0xf) don't match for
> /soc/adc@40012400/channel@15
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x3fc70) don't match for
> /soc/peripheral@40000000/flash-controller@34000/flash@9fc70
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warnings:
> unit address and first address in 'reg' (0x40094000) don't match for
> /soc/peripheral@40000000/usbhs@144000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x3fc70) don't match for
> /soc/peripheral@40000000/flash-controller@34000/flash@9fc70
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warnings:
> unit address and first address in 'reg' (0x40094000) don't match for
> /soc/peripheral@40000000/usbhs@144000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> devicetree error: unit address and first address in 'reg' (0x1) don't
> match for /soc/enet@30be0000/mdio/phy@0
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warnings:
> devicetree error: unit address and first address in 'reg' (0x70000)
> don't match for
> /soc/flash-controller@40020000/flash@0/partitions/partition@700000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x88000) don't match for
> <snip>/flash-controller@43000/flash@0/partitions/partition@80000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x70000) don't match for
> /soc/flash-controller@40020000/flash@0/partitions/partition@700000
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x1) don't match for
> /soc/enet@30be0000/mdio/phy@0
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This fixes the following warning:
> unit address and first address in 'reg' (0x2) don't match for
> /enet@42890000/mdio/phy@0
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Add the function, i3c_device_is_controller_capable, to determine if
a target is controller capable.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The Active Controller data struct for static addr is to always be
0x7E. This is so the active controller can be identified according
to section 5.1.9.3.7 of the I3C v1.1.1 Specification.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The dev argument was missing for the doxygen for the function
i3c_bus_deftgts. Add a comment for it.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Use `test_adc` in io-channels to be consistent in whole
tests/drivers/build_all/sensor/adc.dtsi file.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Do not use SYS_INIT for initializing irq_offload when enabled, instead
using a new interface that is called during the boot process for all
architectures.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
