Add unit tests of the CCID functions.
To support these new tests, the GATT mocks need to
support dynamic GATT DB so we can add and remove
a service that contains CCIDs.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Move the CCID header to the include directory
to make it public.
This also compiles the ccid.c file whenver CONFIG_BT_CONN
is enabled, rather than having an additional Kconfig for it,
since the API is now public and may be used by other than
our internal services.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Rather than throwing an assert, it will now do a better
check for already-allocated CCIDs and return an error instead.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
alloc_value is more correct as it does allocate a new
value, rather than just returning/getting a value.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This adds support for J-Link tunnels, which run on top of an IP network
and therefore uses the -IP option. J-Link tunnels are identified by a
tunnel: prefix instead of a bare IP address. This change checks for the
presence of such a prefix, and choses the -IP transport option if the
tunnel prefix is found.
This has been tested with J-Link Remote Server v7.98g and the SEGGER
tunnel option.
Signed-off-by: Adam Dunkels <adam@dunkels.com>
- Updates teensy board configs for use with new `eth_nxp_enet.c` driver
- Remove ethernet configs from teensy40 (4.0 has no ethernet phy)
- Adds a device entry to include `tests/drivers/build_all/ethernet/`
Signed-off-by: Bernhard Krämer <bdkrae@gmail.com>
The source code uses functions from stdio.h,
such as `sprintf()`, but they are not explicitly included
so that we will add it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The `default y`, which is coupled with
`depends on DT_HAS_REYAX_RYLRXXX_ENABLED` to link the settings with
DeviceTree, which was missing, so I added it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Before unmapping a memory page, the cache is flushed. If the given memory
page is not mapped, this operation ends with a cpu exception on the
ptl platform. Add check if tlb translation is active before flushing.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
The sys_mm_drv_unmap_region_initial function is responsible for unmapping
all unused virtual memory during tlb driver initialization. Most addresses
will not have a mapped page. Ignore the error code indicating unmapped
memory that will occur when trying to unmap.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Enable LPI2C1 on the frdm_mcxw71 board which is connected to a
FXLS8964AF sensor (no driver for the sensor yet).
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The external flash (mx25r64) was accidentally disabled during
testing. The node should be enabled by default like its spi.
This commit removes the status = "disabled";
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
like extra_confs, add extr_args filterable by
soc:<arch>:<extra_args> or
platfrom:<platform name>: <extra_args>
simulation:<simulator name>: <extra_args>
which will only apply to given platform or arch
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Create a macro that encapsulates all filtering and use it in standard
and hexdump macros.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Change logging level definitions to just numbers instead of
numbers with unsigned indicator (e.g. 1 instead of 1U). Levels
from Kconfig comes as just numbers and often levels are used
for IS_ENABLED-type of macros where values are concatenated
into tokens and it actually makes the difference if value is
1 or 1U. It allows minor cleanup in the internal macros.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
No real need to be enabling and disabling IRQs, this logic has been
reported to be causing spurious interrupts and strange behavior, we can
just enable the interrupt and switch to interrupt based logic one time
and keep the interrupt enabled at that point.
Also, fix a W1C bug where |= was used instead of = to clear a flag.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
SOC_FLASH_MCUX has additional dependencies for LPC55xxx CPUs, due to the
fact that the flash should be disabled when executing in nonsecure mode.
Since the merge of HWMv2, this dependency has been set incorrectly at
the SOC level, resulting in the IAP flash driver being enabled when
targeting CPU1, which is incorrect. Fix the Kconfig dependency to
resolve this issue.
Fixes#79576
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The 11v_btm_query shell command was calling parse_number() using
a pointer to uint8_t. This will cause memory overwrite and possible
crash. Convert to use long temporary value to avoid this.
Fix also the output prints in case of an error.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Rework the wifi-shell code so that external subcommands can be
bolted into it easily. This means that the commands should be
created using SHELL_SUBCMD_ADD().
Place the various subcommands in alphabetical order to find them
more easily.
Split long lines in order to pass CI checks.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This change makes sure that when a call to `bt_id_set_scan_own_addr` is
sucessful, i.e., the return value is 0, the `own_addr_type` will
be set by the `bt_id_set_scan_own_addr`.
Not setting the `own_addr_type` in a successful call to
`bt_id_set_scan_own_addr` causes, for example,
the `start_le_scan_ext` method in `scan.c` to use an
uninitialized `own_addr_type`.
Eventually this results in an unexpected failure further down in
`start_le_scan_ext`, when sending HCI command to controller with
an uninitialized `own_addr_type`.
Signed-off-by: Erik Sandgren <erik.sandgren@nordicsemi.no>
Allow using direct IRQs (which are obligatory when buiding
with `CONFIG_GEN_SW_ISR_TABLE=n`).
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
Some deprecated inclusions in max32672.h are causing compilation
warnings, which are interpreted as errors by build tests. Grab relevant
fixes from hal_adi.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Modify the GAP connect to use 30ms. The default parameters
typically ended up with 50ms which is OK in most cases,
but for ISO related test cases, using an ACL interval that
is a multiple of the ISO SDU interval (7.5/10ms) generally
provides better stability. 30ms is the lowest multiple
of both 7.5 and 10ms, and was thus chosen.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
These two functions have stood the test of the time and they have
absolutely nothing specific to sign.py
This has the benefit of transitioning away from west's global and
deprecated logging interface
(https://github.com/zephyrproject-rtos/west/issues/149) and this
deprecation is what prompted this commit: see #79240.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Applies the 'unlikely' attribute to various kernel objects that
use z_unpend_first_thread() to optimize for the non-blocking path.
This boosts the thread_metric synchronization benchmark numbers
on the frdm_k64f board by about 10%.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
If there is a carrier (cable plugged in) on device initialisation
there is a race between the interrupt service and the L2 init.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
Like in all other legacy boards, hw-flow-control should not be
enabled for console UART. With hw-flow-control sample stuck
during printing some initial information and sample appears to
be not working correctly unless com port is opened.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
STM32F1 doesn't have synchronous/asynchronous source clock choice.
The recently added clock check was failing compilation for these series.
This commit removes the check for F1.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The comparator drivers area contains the following incorrect area:
files:
- include/zephyr/dt-bindings/clock/
and contains the following duplicate area:
files:
- include/zephyr/drivers/comparator/
this commit removes them.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Board frdm_mcxc242 does not have UART IP configured.
Add UART configuration and pin control. Set state to disabled,
as it serves as alternative to default LPUART0 or as second
uart only. Add uart to supported features in yaml.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Removes extraneous word in note on net_context struct describing why the
source address is not stored directly in struct.
Signed-off-by: Daniel Mangum <georgedanielmangum@gmail.com>
This commit introduces a new option, OPENTHREAD_CLI_VENDOR_EXTENSION,
in the Zephyr OpenThread module to map the upstream option
OT_CLI_VENDOR_EXTENSION.
OPENTHREAD_CLI_VENDOR_EXTENSION option specifies the path to a CMake
file that defines and links the CLI vendor extension. By setting this
option, it enables the addition of vendor-specific commands to
the OpenThread CLI interface.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Enabling all EAP types for enterprise mode increases
memory usage in both ROM and RAM. Provide config options for each
type to let solutions choose the methods based on their
requirements.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Reduce the valid scaling range for the gain multipliers and dividers to
provide more headroom on int64_t overflows in the calculations. Take
advantage of this headroom to perform all multiplications before
divisions.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Change the unit of the sense resistor in the devicetree binding from
micro-ohms to milli-ohms. This is done for three reasons.
Firstly, the maximum value resistor that can currently be represented
is 4.2 kOhms, due to the limitation of devicetree properties to 32 bits.
Secondly, storing the resistance at such a high resolution makes
overflows much more likely when the desired output unit is micro-amps,
not milli-amps.
Finally, micro-ohms, are an unnecessarily precise unit for the purpose
of these calculations, and a resolution that is not realistic to
achieve. The high resistor resolution results in large divisors that
reduce the resolution of outputs. Unlike resistors characterised down to
the micro-ohm, devices wanting to measure micro-amps are actually
realistic.
Signed-off-by: Jordan Yates <jordan@embeint.com>
If the Broadcast ID is initially set to 0x000000,
which is valid, comparison logic on add of an
actual Broadcast ID of 0x000000 fails.
Likewise for SID.
Moving INVALID_BROADCAST_ID define to bap.h
Signed-off-by: Lars Knudsen <LAKD@demant.com>
The event is sent from both WPA supplicant and hostapd, but hostapd
should only be sent when using hostapd to create the AP.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Instead of having one large compile.sh for all audio samples,
it has been split into multiple. This makes it easier to
build and run specific tests (e.g. BAP or CAP), without
having to build all of them.
This also makes it easier to expand later, without
creating one huge compile.sh file.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
There is nothing like AMD-Xilinx Inc. That's why use full AMD name
instead.
Fixes: 09e2a4e9eb ("drivers: ipm: add zynqmp r5f support")
Co-developed-by: Mubin Sayyed <mubin.sayyed@amd.com>
Signed-off-by: Mubin Sayyed <mubin.sayyed@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
