So that we can stop using the artificial riscv32/64 dual naming. This
patch temporarily allows using both, riscv or riscv32/64.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Because the riscv32/riscv64 is redundant, one can get the same
information combining CONFIG_ARCH + CONFIG_64BIT.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add an utility function to check if the supplied IPv6 address
is one of the possible private IPv6 address range.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add an utility function to check if the supplied IPv4 address
is one of the possible private IPv4 address range.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Apply ranges to DHCPv4 server timeout Kconfig options, so that it cannot
be set to a negative value by mistake.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Verify that declined addresses are not permanently blocked - i. e.
expire after configured timeout and in case of free address shortage,
can be reused.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In case conflict is detected (either due to receiving Decline message or
due to ICMP probe getting reply), the conflicting address becomes
blocked for further use.
Although the RFC is not specific about how long should the address be
blocked, it make sense to implement some fallback mechanisms to reuse
blocked addresses in the server, otherwise, after longer period of
operation, it may run out of usable address.
This commit adds a timeout for declined addresses, so that by default
the address is marked back as "free" after 24 hrs (default lease time).
It also implements a mechanism, which allows to re-use the oldest
declined entry in case the server runs out of fresh addresses to assign.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add a sign_extend and sign_extend_64 functions, same as the Linux
sign_extend32 and sign_extend64 one. This is useful for sign extending
values smaller than 32 bits.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Drop a bunch of display functions that only return "not supported", the
display API already handles these by checking for NULL API function
pointer.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Since PR, PR_SHELL, PR_ERROR, PR_INFO, and PR_WARNING already have
an embedded `sh` NULL check, we can remove the change from PR #68809.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
It is possible that the `sh` was not set before use.
This change adds a NULL check for `sh` in the following macros:
PR, PR_SHELL, PR_ERROR, PR_INFO, and PR_WARNING.
In case `sh` is NULL, the above macros will call `printk` instead.
Fixes#68793
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This commit renames a few variables and changes the
type and adds some additional checks.
It moves stream specific data to the shell stream
struct, but still keeps the global values that were used
to initialize the LC3 encoder
The purpose of this is to better allow for a future LC3 decoder
without any clashes in names or the like.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The start and stop of the DMA channel provides useful information in
default logs and they are not too frequent to cause bandwidth issues.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
The LOG_* macros already print the module name and the function, printting
again the __func__ have no additional benefit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
The LOG_* macros already print the module name and the function, printting
again the __func__ have no additional benefit.
The debug prints lack context which can be used to identify the channel
which the message was printed for.
For example:
<inf> dma_dw_common: dw_dma_stop: dw_dma_stop: dma 0 channel drain time out
when multiple channels from multiple controllers are used we don't know
the exact channel that has been stopped:
<inf> dma_dw_common: dw_dma_stop: dma@7c000: channel 0 drain time out
<inf> dma_dw_common: dw_dma_stop: dma@7d000: channel 0 drain time out
Convert all LOG prints to add usable context to them and use the following
pattern wherever it is possible:
dma_dw_common: <function name>: <DMA device name>: message
for example:
<inf> dma_dw_common: dw_dma_stop: dma@7c000: channel 0 config
The parameter list of dw_dma_avail_data_size() and dw_dma_free_data_size()
extended to pass the dev pointer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
This commit adds tx power config options for nRF54Hx and nrf54Lx
SoCs, as well as the new radio defines.
Signed-off-by: Kyra Lengfeld <kyra.lengfeld@nordicsemi.no>
RPMsg currently sends four dummy bytes over the IPM when sending a
notification/interrupt to another CPU. However, most IPM drivers
support sending messages with no data transfer, and for some IPM
drivers, like the STM32 HSEM IPM driver, data transfer is not
possible at all, thus breaking compatibility. To fix this, send an
empty message with size 0 instead of a dummy message if the STM32
HSEM IPM driver is active.
Signed-off-by: Celina Sophie Kalus <hello@celinakalus.de>
IPM drivers are commonly used to send notifications/cause interrupts
without any transfer of data. To add this use case in the ESP32 IPM
driver, the guard statement is appended so that the pointer to the
data buffer is allowed to be zero only if the size of the data to be
transferred is zero. If size is given as 0 and data is equal to NULL,
we are thus only using the IPM as a doorbell, not to transfer data.
Signed-off-by: Celina Sophie Kalus <hello@celinakalus.de>
Using the `bap preset` command it is now possible to set all the
codec configuration data and metadata value at runtime. This will
allow to set specific values for each stream in each direction.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Instead of the default presets being pointers, they are changed to
allocated structs so that they can be modified.
This will allow us to modify the config and metadata in a later patch.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Rename uart and uart_async bsim test to reflect
testing of hci_uart sample using UART driver
variants under bsim simulations.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The tests `hci_prop_evt` and `host_long_adv_recv` used `bt_recv_prio`,
and so relied on an extra config option `CONFIG_BT_RECV_BLOCKING`. This
patch replaces the use of `bt_recv_prio` with `bt_recv` and restores the
use of the default option for `BT_RECV_CONTEXT`.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
This commit removes extra rescheduling in the extended advertiser after
the last advertising has been finished. This commit also removes the
`ADV_FLAG_SCHEDULED` flag as not needed anymore.
This extra rescheduling and the flag were needed to delay the next
advertisement by 20ms. Now, when the delay is removed the advertiser can
pick the next advertisement from the pool and push to the host right
away.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This patch allows selecting the combination of `CONFIG_BT_RECV_WORKQ_BT`
and `BT_LL_SW_SPLIT`. The implementation of `bt_recv_prio` is copied
from `hci_raw.c`. This ensures the order of packets is the same as when
the controller's `hci_driver.c` is off-chip and sends HCI over UART.
Without this patch, the Zephyr LL driver will duplicate some events on
behalf of `hci_core`. This duplication is not wanted when
`CONFIG_BT_RECV_WORKQ_BT=y`.
The above mentioned duplication is not sound and is evidenced in logged
warnings, e.g. in `tests/bsim/bluetooth/host/l2cap/stress` with
`CONFIG_BT_RECV_WORKQ_BT=y` logging "no transition".
This patch is a step towards the deprecation of
`CONFIG_BT_RECV_BLOCKING`. `CONFIG_BT_RECV_BLOCKING` is complicated and
tightly coupled to `hci_core`. In the future, removing
`CONFIG_BT_RECV_BLOCKING` will give a cleaner separation between
`hci_core` and the drivers and allow `hci_core` to evolve without
changes spilling out into the drivers.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
The goal is to not access `buf` in the non-prio `hci_disconn_complete`
so that the buffer does not need to be retained.
This commit moves the copy of `conn->err` to the prio handler.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Fix CONFIG_BT_CTLR_TIFS_HW conditional compile by replacing
DPPI_PRESENT with CONFIG_BT_CTLR_TIFS_HW.
HAL_SW_SWITCH_TIMER_CLEAR_PPI can be same as
HAL_RADIO_END_TIME_CAPTURE_PPI, and this is ok as same
bit will be used to disable PPI/DPPI.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit introduces a driver for ADC keys, a common circuit design where
keys are connected to an ADC input via a resistor ladder.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Always execute tx_notify from a single context. For sanity and ease of
debugging / observability.
The previous behavior was calling from BT_RX thread + system workqueue.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Changes include:
- Improving handling of frames for unconfigured DLCIs.
- Adding logs and outputting error codes in failure cases.
- Adding warnings to not reuse buffers.
- Fixing comments.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
In the function bt_l2cap_chan_set_state, BR
channel is treated as LE Chan.
The BR L2CAP channel state is updated
incorrectly.
Add a function bt_l2cap_br_chan_set_state
for BR L2CAP channel. For BR/EDR channel,
call bt_l2cap_br_chan_set_state directly.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Adds use of CHARGER_PROP_DISCHARGE_CURRENT_NOTIFICATION and
CHARGER_PROP_SYSTEM_VOLTAGE_NOTIFICATION_UV to the charger
sample application.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Adds the path to the sample application in the charger API
area of the MAINTAINERS file.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Moves the charger API sample app from samples/charger/ to
samples/drivers/chargers/ as mentioned in issue #65032.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
