Add test for the experimental feature GPIO_ENABLE_DISABLE_INTERRUPT,
which covers APIs gpio_pin_interrupt_enable() and
gpio_pin_interrupt_disable().
Signed-off-by: Sung-Chi Li <lschyi@google.com>
Implement the driver method pin_interrupt_enable and pin_interrupt_disable.
This commit fixes getting the get_pending_int by updating the interrupts
field in the gpio_emul_data filed when interrupt is triggered. Also,
introduces a new filed enabled_interrupts to better simulate the
behavior of the interrupt pending and whether the interrupt is
enabled/disabled.
Signed-off-by: Sung-Chi Li <lschyi@google.com>
Add pin_interrupt_enable and pin_interrupt_disable in gpio_driver_api,
and add corresponding APIs in gpio.h for application to enable/disable
an interrupt without reconfiguring again.
This CL also Create a new Kconfig option for this feature.
Signed-off-by: Sung-Chi Li <lschyi@google.com>
This function had only one use in SenML CBOR formatter and it
contained some specific tweaks, so move the function to be a
static member of that module.
Fixes#53674
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Fix RAM overflow building for direction finding feature on
nRF53 Series, by reducing thread stack sizes. And move
building DF plus CIS feature to hci_uart sample from
hci_rpmsg sample.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fail compilation when incorrect configuration is detected, i.e. when
SHELL_BACKEND_SERIAL_CHECK_DTR is set but UART_LINE_CTRL is not set.
Use periodic timer to wait for DTR instead of waiting in uart callback
to prevent blocking caller workqueue and/or sleeping in ISR.
DTR check was only ever supported with interrupt driven backend so add
appropriate depends on to Kconfig.
Fixes: e9f238889b ("shell: uart: Add waiting on DTR signal before
sending data")
Fixes: #47120Fixes: #54705
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
When LwM2M engine is paused, stop functionality just
marks the intent and when we resume, it will send the
de-registration if that was requested.
Otherwise it will stay in SUSPENDED state until resumed
and then goes into ENGINE_DEREGISTERED -> IDLE.
This also removes the blocking loop from lwm2m_rd_client_stop().
It does not need to block because lwm2m_rd_client_start()
is already checking if client is in IDLE.
Fixes#56254
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Use the LTDC in combination with the DSI HOST makes the pinctrl obsolete.
DSI HOST has dedicated pins.
Signed-off-by: Rico Ganahl <rico.ganahl@bytesatwork.ch>
Adjust size and alignment of stacks and application memory partitions
according to granularity of PMP.
Signed-off-by: Rick Tsao <rick592@andestech.com>
Ignore the link clock_source for non-ACE platforms instead of throwing
an error when it is set in the topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
We need to ensure that the XEC GIRQs are initialized after the
XEC ECIA device. Right now we depend on the linker ordering
things correctly since everything is at INTC_INIT_PRIORITY
priority
Set the XEC GIRQs to 41 so the init priority is one more than
INTC_INIT_PRIORITY that is used by xec-ecia.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
The driver has been recently moved under the input subsystem but the
corresponding driver was left over. Move it from kscan to input.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fixes an issue whereby a Kconfig dependency was dropped and
selects UART_LINE_CTRL in addition by default when shell is
enabled to alleviate an issue with possible garbage data at boot.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Fixes an issue whereby a Kconfig dependency was dropped and
selects UART_LINE_CTRL in addition by default when shell is
enabled to alleviate an issue with possible garbage data at boot.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Fixes an issue whereby a Kconfig dependency was dropped and
selects UART_LINE_CTRL in addition by default when shell is
enabled to alleviate an issue with possible garbage data at boot.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Fixes an issue whereby a Kconfig dependency was dropped and
selects UART_LINE_CTRL in addition by default when shell is
enabled to alleviate an issue with possible garbage data at boot.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Fix RAM overflow by using default values for
BT_BUF_ACL_RX_SIZE and BT_BUF_ACL_RX_COUNT. Default Rx size
of 27 is sufficient for nRF51 SoC, as it does not support
data length extensions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Configure the tests/drivers/spi/spi_loopback to run on the
stm32h573i_dk disco kit with DMA transfer
use gpdma1 or gpdma2.
GPDMA1 or GPDMA2 have the same request for spi2 transfer.
Connect D11 and D12 of the ARDuino CN13 connector to PASS the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the configuration for running the spi_loopback (interrupt mode)
on the stm32h573i_dk disco kit.
The SPI2 is enabled by the board DTS
Connect pin D11 and D12 on the Arduino connector (CN13)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Added support for async APIs for ns16550. This will be
enabled by kconfig CONFIG_UART_ASYNC_API.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
There have an extral TBE interrupt event though we have cleared the
SPI_CTL1_TBEIE bit. To cover this situation, add a on_going check
before enter exchange function.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Add an escape hatch so users can insert a customizable delay
between asking the board to reboot into bootloader mode and
trying to program the new image. This lets people account for
OS-specific enumeration time done after the board resets.
Fixes: #56540
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
device_extern.h was still generated with an #error directive, not really
useful was it was never designed to be included directly, but via
device.h.
Fixes#56425
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Various bluetooth tests fails to link because bt_le_ext_adv_set_data
can't be resolved. Solve this by adding a check CONFIG_BT_EXT_ADV
around use of bt_le_ext_adv_set_data.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Add esp32s3 overlay to qdec sample to ilustrate
the use of PCNT in quadrature enconder mode.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
