Assuming gpio devices are required by pinmux which is used
by any device make it a device that is initialized in preliminary
steps of platform init.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move GPIO devices clock handling in stm32_pin_configure function
which is also used in stm32_setup_pins.
Additionally, add device usability check to be sure gpio driver
was initialized before being used by pinmux pseudo driver.
Last, going from the assumption that GPIO devices should be
initialized before being used by pinmux, then there is no need
to enable clock in case CONFIG_PM_DEVICE_RUNTIME=n.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
So far only upstream boards were listed. Use just introduced
zephyr_module.parse_modules() function to get information about
out-of-tree board roots. Append them to user provided args.board_roots,
so out-of-tree boards from west modules are listed as well.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add parse_modules() function, which will offload most of the work in
main() and additionally allow external Python code to use that function.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Refactor Periodic Advertising time update function to use
caller supplied Periodic Advertising PDU to calculate the
time reservations.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Apply suggestions from code review, and change to using
BT_HCI_ERR_SUCCESS instead of returning 0.
Co-authored-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix Extended and Periodic Coded PHY time reservation. The
define earlier used does not have calculations for Coded
PHY.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implementation to update Periodic Advertising time
reservations when advertising data and/or CTE length is
updated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add check for already enabled and started Periodic
Advertising when HCI LE Set Periodic Advertising Parameters
command is called.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor out Periodic Advertising time calculations so that
it can be reused when PDU length is updated as part of
advertising data updates.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implementation to update Extended Advertising time
reservations when advertising and scan response data are
updated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Export the function calculating the primary channel
advertising event time reservation, so that Extended
Advertising implementation can reuse it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor out Extended Advertising time calculations so that
it can be reused when PDU length is updated as part of
advertising data and scan response data updates.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implementation to update legacy advertising time
reservations when advertising and scan response data are
updated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor out advertising time calculations so that it can be
reused when PDU length is updated as part of advertising
data and scan response data updates.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use a conservative turnaround time of 150us covering slower
nRF51 and faster nRF52 CPU that influence the turnaround
timing.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add nucleo_wl55jc to platform_allow for lora send/receive and class_a
samples. The board has a variation of the sx1262 driver, this should
allow to build test that code path.
Fix the existing config as well to specify the platforms on a single
line, as currently only the last entry is considered.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Define the subghz radio node in the module dtsi file, with the internal
RF switch connection and TCXO setting, and point at it from the
corresponding dev board file.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add a device node for the subghz radio in stm32wl.dtsi. The radio is
present in all chips of the series, so having the node there with the
common properties simplifies the board dts files.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add support for the STM32WL integrated radio, based on the sx1262. The
STM32WL implementation does not use any GPIO, and the signals are routed
to other units of the SoC and accessed with the ST HAL.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Convert the standalone part of the sx126x driver to the new gpio_dt_spec
APIs. This allows moving the specific GPIOs in that part of the driver
and out of struct sx126x_data.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
This adds support for controlling the SUBGHZSPI NSS line in STM32WL
devices. This is a special dedicated SPI port only connected to the
radio device internally, chip select happens through a bit in the PWR
module. Adding a special dt-property to identify the port, it all gets
built out on non-WL devices.
Deduplicate the existing dts bindings in the process, and add the new
one for the special spi with the new property.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add a dts node for st,stm32wl-subghz-radio. The device is integrated in
STM32WL series SoCs, and based on the sx1262, but it does not use any
gpio as all the necessary signals are internally connected to various
SoC units.
To account for that, make the redundant gpio optional in the template
files, but mark them as required in the sx1261 and sx1262 definitions,
to match with what's used in the driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Current impĺementation fails due to missing stop bit
when reading data. This fixes it and refactor the implementation
by adding k_busy_wait when waiting I2C bus completion.
Also, this implementation is based on esp-idf v3.0.
It will be refactored based on latest esp-idf v4.3 using proper
low level calls.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Fixes#34015
The STMPE1600 is an I2C based GPIO expander. This initial patch
only supports reading from/writing to the pins on the STMPE1600,
and there is currently no support for interrupts.
Signed-off-by: Titouan Christophe <moiandme@gmail.com>
Introduce a set of header files to be able to define and declare
sections and regions in the linker script. Introduce also DT helpers to
retrieve data back.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
To be able to get a tokenize DT string without the quotes. Deprecate
also DT_ENUM_TOKEN and DT_ENUM_UPPER_TOKEN.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This reverts commit 9e58a1e475.
This change is in conflict with commit 94f7ed356f ("drivers: serial:
add a dummy driver for vnd,serial"). As a result two equal serial
devices are defines, resulting in link error.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Fix a couple of issues related to Power Management:
1. A build error because 'dev' was used even if not declared
in the caller routine scope
2. The lis2mdl power management init specific routine was
not declared in in the device instance definition
Signed-off-by: Armando Visconti <armando.visconti@st.com>
So far modem API used UART device names / labels. Change API to operate
on device pointers instead, so that we stop using device_get_binding()
in modem core and in some DT compatible modem drivers.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
