Clarify the PWM pwm_pin_set_cycles() function API details.
The API aims for synchronous (glitch-free) updates of the PWM period and
pulse width, but not all PWM controllers support this.
Similarly, the API aims for independance between channels on
multi-channel PWM controllers, but not all PWM controllers support this.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
USB audio class samples are generic and can be built for any
board that supports USB device and isochronous endpoints.
Add app.overlay that uses reference to zephyr_udc0 and remove
board specific overlays.
Note: USB audio is still experimental and even though the sample can
be built for specific platform, it does not mean that it can be run
on it without issues.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
USB devicetree nodes in Zephyr have different names,
mostly derived from the designations in data sheets.
Add zephyr_udc0 (USB device controller) nodelabel to
specific USB node to allow generic USB sample to be build.
Follow up on commit b4242a8 ("boards: add USB node aliases")
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This reverts commit e53371bbc0bc37d911884937199733f23c43fb21.
The "usbd0 aliases" approach has not proven to work.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Update periodic advertising data update rate. The periodic advertiser
is configured with a periodic advertising interval of 2.4 seconds but
updating the data every second. This leads to many of the advertising
data values not being sent at all.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Adds a test to check value of the IV Update
counter at the time of provisioning based on
the status of IV Update flag. Also ensures that
the counter is reset if the mesh stack state
is reset.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
When device is first provisioned with IV Update
flag is set to 0, it should wait for minimum of
96 hours before going into IV Update In Progress
state. Such limit does not apply, if device is
provisioned with IV Update flag is set to 1.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
This commit tests persistence storage for access layer:
- Model publication
- Model subscription
- Model app keys binding
- Model data
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This commits fixes an issue where an existing entry in a settings file
causes settings file corruption when storing new value.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This commit adds missing API that allows to discard the Subscription
List of a vendor model.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Name length can't be longer than 8 bytes. This needs to be clarified
in the bt_mesh_model_data_store() documentation.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Change the fail handling of setting the CIG parameters
(or when allocating the CIS) to unref the ISO conns
instead of calling cleanup on them directly.
This fixes an issue that if the CIG parameters failed,
then the iso conns would not be unref'ed and we could
not try again.
Unref'ing an iso conn will call cleanup once it hits 0
refs.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
A channel should only be allowed to unbind when in
the BT_ISO_BOUND state. If it is in a disconnected state,
then it the function would have meaning. If it is a connected
state, unbinding it would generate an error when removing
the CIG, which would fail silently.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Enable PWR clock unconditionally for L4, L5 and U5
like it is done on other stm32 series
Fixes#37781
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This is now failing an edtlib check for unknown vendor prefixes.
I can't find a reason to use a vendor prefix in application-local
bindings like this, so just remove it wherever it appears by
normalizing to test-foo-compat instead of test,foo_compat or
test,foo-compat.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Increases the default CONFIG_TEST_EXTRA_STACKSIZE for the 32-bit RISC-V
architecture. This fixes the portability.posix.fs test on the
qemu_riscv32 platform.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add unit tests for HCI commands:
- HCI_LE_Set_Connection_CTE_Receive_Parameters,
- HCI_LE_Connection_CTE_Request_Enable.
Tests validate current implementation of commands handling in HCI/ULL.
Handling of the HCI_LE_Connection_CTE_Request_Enable is not complete,
thus tests don't validate positive behavior the functions.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
LE Set Connection CTE Receive Parameters HCI command size may not fit
into HCI TX command buffer size, which default value is 65 bytes.
For platforms other than Nordic there may be up to 75 antenna IDs
put into the command.
Added new default value for SOCs not compatible with Nordic to
extend default TX buf size to 83 bytes (75 bytes for antena IDs,
5 bytes for other command parameters, 3 bytes for command header).
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add functions that handle enable CTE request control procedure
request from host.
Implementation of ll_df_set_conn_cte_req_enable in ULL is partial.
It will be integrated with refactored implementation of control
procedures.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add struct ll_df_conn_rx_params sturcutre to struct lll_conn.
This is storage for parametrers required to configure radio
for CTE reception in connected mode by lower link layer.
Add required includes to make the controller code compilable
after change struct ll_conn.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
HCI_LE_Set_Connection_CTE_Receive_Parameters handling is required to
enable sampling of Constant Tone Extension in connected mode.
The commit adds handling for HCI_LE_Set_Connection_CTE_Receive_-
-Parameters command.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add struct ll_df_conn_rx_params sturcutre to struct ll_conn.
This is storage for parametrers required to configure radio
for CTE reception in connected mode.
Add required includes to make the controller code compilable
after change struct ll_conn.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add new strcture type for storage of CTE receive parameters.
The structure will be used in to store parameters for connected mode.
The parameters provided by HCI commands for receiving CTE
in connected mode and disconnected mode are a bit different.
There is common subset of parameters but extraction of those
into common structure would increase of size of other stuctures
that aggregate them.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Code related with connected mode was in middle between connectionless
RX and TX. Moved to the bottom of the file.
Added missing compilation guards for ll_df_set_conn_cte_tx_params.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add features: connection CTE request, connection CTE response
and receiving constant tone extensions; to HCI and features
supported by controller.
The features are not enabled yet.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Compute the SHA256 hash of the downloaded image and compare that with
the hash in the deploymentBase to guarantee that only the correctly
downloaded image will be flashed.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Use a semaphore to prevent the hawkbit_probe from running more than once
at the same time since it reset the hawkbit context on entry and will
affect other running instance.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Fix multiple typos and make the sample's log output consistent
with the subsys.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Co-Authored-By: Sylvio Alves <sylviojalves@gmail.com>
The delay will ensure last byte has been latched in before
This also change the method of reading status register from re-send
read status command on each read to read status register continuously.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
When there is no grove sensor driver enabled, cmake warns
that the library has no sources. Fix that by adding
a new kconfig to be used by CMake to selectively
include the grove directory.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
