NPCX7 includes a 10-bit resolution Analog-to-Digital Converter (ADC). Up
to 10 voltage inputs can be measured and a internal voltage reference
(VREF), 2.816V (typical) is used for measurement. It can be triggered
automatically in Autoscan mode. Each input channel is assigned a
separate result register, which is updated at the end of the conversion.
The CL also includes:
— Add npcx adc device tree declarations.
— Zephyr adc api implementation.
— Add adc definitions of npcx7 in
tests/drivers/adc/adc_api/src/test_adc.c for supporting test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
nsim_hs_smp has 2 cores, and CONFIG_MP_NUM_CPUS defalut value is 2.
But some tests will have extra config: CONFIG_MP_NUM_CPUS=1, so we
need to launch cores according CONFIG_MP_NUM_CPUS, not using a fix
number 2.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Instrs_per_pass option specify the number of instructions excuted
before simulator switches operations. the default value is 512. If we
specify a small value for it the debugger's overhead will increase
significantly for simulation because of the time taken to rapidly
switch operations. And the overhead will cause some time critical
task failure.
Restore instrs_per_pass value from 10 to default 512, we will have a
good sanitycheck result for nsim_hs_smp.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
The SAM4E/S SoC have a ROM bootloader named SAM-BA. Add bossac
to the board west runner list. This requires Zephyr SDK 0.12.0.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Some Clocks have ifdefs only for clock_control_on but are missing
them for clock_control_off.
Additionally return ahb_clock clock frequency for stm32g0
STM32_CLOCK_BUS_IOP in stm32_clock_control_get_subsys_rate.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Commit: 11de84a6b4ec4be23bed92bf2d8d36f3876189b6 moved shell core
tests from tests/shell to tests/subsys/shell. Remove obsolete path
from MAINTAINERS.yml accordingly.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
When CONFIG_BT_CTLR_CONN_META is enabled and the ticker "must_expire"
feature is used, collisions may cause incorrect decrement of the
supervision_expire counter, resulting in a too early link supervision
timeout.
Signed-off-by: Morten Priess <mtpr@oticon.com>
The commit removes a leftover configuration of the log management that
has never worked and has been removed with the commit
0bb466c34e4fe863733a929baa8f51981263ce3d to apache/mynewt-mcumgr.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
After the change SHA1: 3498d43784 the
local-mac-address property is no longer parsed correctly when it is
defined in the '&enet` DTS node on k6x SoCs (e.g. frdm_k64f and
ip_k66f).
The problem is with value to which the
NODE_HAS_VALID_MAC_ADDR(DT_DRV_INST(n)) macro is resolved.
If the 'local-mac-address' is present it returns
'(!((0 == 0) && (0 == 0) && (18 == 0) && (19 == 0) && (0 == 0) && \
(16 == 0)))' [*], otherwise it is 0.
As COND_CODE_{01} only accepts 0 or 1 as its first argument, it all
worked until the 'local-mac-address' was not defined. When present
the first argument to COND_CODE_{01} macro was [*] and it caused
build break.
Fixes issue: #30354https://github.com/zephyrproject-rtos/zephyr/issues/30354
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If interrupt handler contains while loop which depends on
uart_irq_tx_ready() and uart_fifo_fill is called inside this
loop then if TXSTOPPED event occurs while code executes the
loop then uart_irq_tx_ready() will return true but uart_fifo_fill
will fail to write any bytes. That is because fifo_fill_lock is
cleared in handling of TXSTOPPED. To solve that added clearing
the lock inside uart_irq_tx_ready() if STOPPED event is detected
there.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Set work item's flag in pending state, it cannot be append to a
workqueue. Improve branch coverage of function k_work_submit_to_queue().
Signed-off-by: Ying ming <mingx.ying@intel.com>
Fix incorrect initiator window offset used when in continous
initiator scanning. Calculated window offset to free time
space after existing central connections is not decremented
correctly when there is change in window at every initiator
scan interval.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix corruption of ftr auto-variable due to reuse to insert
new node rx into the received auxiliary PDU chain, which can
cause corrupt reference used later in the implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Changed algorithm of checking for pending thread in mem_slab.
Check for pending thread now is done only if there is
no memory left.
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
There was a regression introduced when reordering function parameters
check. It is valid to pass NULL semaphore with zero timeout, so fix
parameter check to respect that.
Fixes: 67976f8686 ("drivers: modem: verify send semaphore before
taking any action")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This adds a sample application for testing
the LiteX clock control driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This enables the LiteX clock control driver for litex_vexriscv platform.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This commit adds LiteX SoC Builder clock control driver for MMCM
module. It gives ability to change frequency, phase and duty cycle
on up to 7 clock outputs.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This adds bindings for the LiteX clock control driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
SRAM base address and size are currently hardcoded in the defconfig.
This is wrong because symbols like KERNEL_RAM_SIZE and KERNEL_VM_BASE
are not currently being set. Fix this by adding the correct DTS entry.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
CONFIG_IWDG_STM32_TIMEOUT allowed values of 100 us for initial watchdog
timeout, which was actually rounded to zero in the driver, which uses
milliseconds resolution for timeouts. This resulted in the reload value
being set to maximum possible (calculation: 0U - 1).
This commit updates the calculation of timeout minimum and maximum
values considering the actual LSI frequency of the used MCU.
As the resolution of CONFIG_IWDG_STM32_TIMEOUT in microseconds doesn't
make sense if the driver supports only milliseconds, it is renamed to
IWDG_STM32_INITIAL_TIMEOUT (this prevents accidental wrong settings in
existing firmware) and the unit is changed to ms.
Signed-off-by: Martin Jäger <martin@libre.solar>
Fix PHY Update control procedure to accept the preferred Tx
coding options (S2 or S8) requested even if there is no
actual PHY change happening on procedure completion.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Both AdvA and TargetA have constant offset in extended header so it
makes sense to have dedicated definitions for those numbers.
AdvA is always placed at the beginning on extended header while TargetA
follows AdvA directly. There are no PDUs without AdvA and with only
TargetA.
Offsets of other fields depends on extended header contents and thus
are non constant.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
'ext_hdr' member only covers extended header part of 'ext_hdr_adv_data'
and with addition of 'data' member to 'pdu_adv_ext_hdr' those can be
used to quickly access both extended header flags and data directly
from 'pdu_adv' without need for extra local variables and casts.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
pdu_adv_hdr name is quite confusing since it suggests some generic
header for advertising PDUs while this in fact is extended header
which is a part of common extended advertising payload and only applies
to extended advertising PDUs.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
The 'adi' part of that member name does not make sense since ADI is
already part of extended header, so we only have 'extended header' and
'advertising data'.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
z_tick_sleep was using int32_t what could cause a possible overflow
when converting from k_ticks_t.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This patch activates FPU feature for main thread if FPU related
configs (FPU, FPU_SHARING) are enabled.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
If handle mapping is enabled, we need to use proper advertising set
handle in HCI event.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
When legacy set is configured we need to make sure scan response is
properly initialized with empty data. For extended sets we should not
touch scan response on configure since data for those sets have to be
set explicitly, e.g. we cannot enable scannable advertising set if no
data was set.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
It was possible that settings_line_entry_copy() did unaligned
flash write.
This patch introduce respecting the flash write-block-size.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
AdvA in extended advertising PDUs was only set if random address was
used. This patch enables proper support for AdvA/TgtA in those PDUs
also with LL Privacy enabled.
On enable, we always update advertising PDU (i.e. ADV_IND, ADV_EXT_IND
or ADV_AUX_IND, depending on advertising set parameters) as well as
scan response PDU.
On RPA timeout, we simply copy old PDU as-is and update AdvA in new
PDU, since both PDUs are exactly the same (except AdvA) so no need to
recreate it step-by-step.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Guards the functions with CONFIG_BT_CTLR_HCI_ADV_HANDLE_MAPPING
and added a non-HCI inline function for them.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Removed the node_rx argument for the BIG create/terminate
functions. The event should not be sent right after the
command, but needs to wait for transmissions of
empty BIS packets or BIG terminate indications.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Moves the ISO tx pool and functions from ull_adv_iso.c to
ull_iso.c as the pool and functions will be shared between
BIS and CIS.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
