Introduce a new scheme to define clock bingings on u5.
In a next steps, this new scheme will allow to provide u5 specific
alternate and complementary device clocks.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This new binding allows to work on providing stm32h7 specific
alternate and complementary device clocks.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
those bindings are no more needed since pinmux was
deprecated in favor of pinctrl.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
to support implementation and peripheral usage of the pinctrl
driver API.
Removes deprecated "use-iomux" property from the SPI node.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
After pinctrl's subsystem support, I2C pin properties are
no longer required for pin muxing, however, this information
is still valuable in an eventual FSM failure if the target
SoC has no harwared mechanisms to support bus recovery.
In this case, bus recovery uses pin information to restore
the I2C bus state.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Adds hda link in and out drivers. The link in and link
out channels of HDA have small differences
with the host channels. Updates the existing
cavs_hda drivers and code to account for these
differences.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
all the consumers of the obsolete pinmux driver is
updated to use pinctrl API, this commit removes
the pinmux driver and assosciated sections.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Add pinctrl driver for CC13XX/CC26XX family of SoCs
to facilitate transition from pinmux to pinctrl.
`IOCPortConfigureSet()` from TI hal driverlib used to
implement the generic pinctrl driver.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
LPTIMER has a different `countermode` meaning.
We shall exclude introduced property from lptim bindings.
Alternative property (e.g. `external-mode`) can be added
later on to support external counter mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This PR fixes up the Scatter-Gather EDMA mode for the MCUX EDMA Driver,
as well as enabling the dma reload feature for the same EDMA Driver.
Signed-off-by: Nickolas Lapp <nickolaslapp@gmail.com>
This commit adds a flash_controller node for the stm32u5 soc family
blocks of 8K and erase time given by the Datasheet (with margin).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduces H7 FMC bindings with support for
memory remap or swap configuration.
The following values are supported:
* disabled - default mapping (reset state).
* sdram-sram - swaps the NOR/PSRAM and SDRAM banks.
* sdramb2 - remaps SDRAM bank 2.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
the icm42670 from Invensense/TDK is a 6-axis accelerometer with
gyroscope and temperature sensing capabilities.
this initial driver does not support the devices 2K FIFO or many of the
other advanced features. Instead, only basic features are implemented.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Extend Altera Jtag Uart driver support without Altera HAL driver
by default. uart_altera_jtag_hal.c renamed to uart_altera_jtag.c and
new config, CONFIG_UART_ALTERA_JTAG_HAL is introduced to allow driver
to use Altera HAL driver when needed.
Signed-off-by: Khor Swee Aun <swee.aun.khor@intel.com>
Add the period cell to GD32 PWM compatible and update all boards
accordingly. A period of 20 ms (50 Hz) has been set for all PWM LEDs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
STM32 supports now custom PWM flags, include them by default as done for
the standard flags.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
add soc level pinctrl node to LPC55s6x DTSI file, to be populated with
pin groups at the board level.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rather than specify input clock for each peripheral individually, instead
specify the relevant clocks in DTS.
This will enable easier support for non-default coreclk on fe310 in a
follow-up CL.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
