The commit adds dependency on Kconfig FLASH_PAGE_LAYOUT to subsystems
that really require it:
FCB, NVS, LittleFS
and removes direct selection from '*.conf' files where no longer
needed.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Let's increase the timeout for a few tests whose
timeout is less than 3x a typical execution time in CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove the boilerplate which is not necessary beacuse
it is already provided by the common scripts
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
In all scripts, where we were using the BOARD variable
let's use BOARD_TS which is the full BOARD target string
with "/" replaced with "_"
This is neccessary to support hwmv2 board names
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
One of these tests has been seen failing in older slower
computers due to timeouts, let's increase the timeout so
we don't break in those cases.
Note this timeout is just a safety to eventually kill
hung simulations even if nobody presses Ctrl+C.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Commit adds const qualifier to models metadata.
Specification claims: Composition Metadata Page 0
shall not change during a term of a node on the network.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
The stack manages to suspend the advertiser before it finishes
transmitting the Outbound PDU Report message to confirm the transmission
of a Provisioning PDU. The test requires the server to become
unresponsive when the Provisioning PDU is sent to the unprovisioned
device to test timeout of the provisioning protocol.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Now, when the deadlock is removed from `bt_mesh_adv_disable` function,
the advertiser can be disabled from the `bt_mesh_send_cb`
callbacks.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Add a test that checks that both advertisers, the legacy and the
extended behaves identically when the stack is suspended, in particular:
- `bt_mesh_send_cb.end` callback is called with error code `0` for the
advertisement that the advertiser already pushed to the ble host
(called `bt_mesh_send_cb.start`),
- `bt_mesh_send_cb.start` callback with error `-ENODEV` is called for
every advertisement that was pushed to the mesh advertiser using
`bt_mesh_adv_send` function before the stack was suspended,
- `bt_mesh_adv_create` returns NULL when attempting to create a new
advertisement while the stack is suspended.
The `bt_mesh_adv_disable` is called from the work because calling it
from the `bt_mesh_send_cb.start` callback will cause a deadlock.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This commit changes error code returned by `k_sem_take` when it times
out from `-EAGAIN` to `-ETIMEDOUT` because `bt_le_scan_start` also
returns `-EAGAIN` if bt device is not ready, which may lead to invalid
test behavior.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Adjust mesh test timing and timeout value for Advertising
Extensions use/fix in Zephyr Controller. The scanning in
Zephyr Controller is delayed when using extended scanning.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
After removing 20ms in advertiser, all subnetwork beacons are sent as high
dense packet of frames with minimal distance between them. That might
cause collisions if beacon interval on devices will coincide.
This commit adds an artificial delay between each subnet advertsing
beacons.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Bluetooth Mesh Protocol 1.1 is backward compatible with Bluetooth Mesh
Profile 1.0.1, therefore the stack can still be qualified for 1.0.1 if
needed. But explicit support for both versions requires additional
maintenance efforts and doubles the CI time. To make the stack
qualifiable for 1.0.1, the one needs to remove Private Beacons reception
and compile out SHA256 algorithm support.
What is changed:
- Removed `CONFIG_BT_MESH_V1d1` option.
- Removed `transport_legacy.c` which was using 1.0.1 implementation. The
new transport layer has new SaR logic that should still be possible to
qualify for 1.0.1.
- Removed the legacy transport Kconfig options. They are superseded by
the new transport Kconfig options.
- Tester app: `overlay-mesh-v1d1.conf` is merged into
`overlay-mesh.conf`.
- Removed BabbleSim tests for 1.0.1.
- Updated documentation.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Enable by default the access layer responses random delays.
Commit also adapts all mesh models, samples and
babblesim tests to use random delay functionality correctly.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Adds two test-cases to `test_suspend.c`, both checking that gatt
advertisement is stopped when suspending Mesh, and that is started again
when Mesh is resumed.
The first test-case involves suspending and resuming Mesh, and
the second test-case involves suspending Mesh and disabling Bluetooth,
then re-enabling Bluetooth and resuming Mesh.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Renames tx to DUT and rx to Tester to clarify roles in test.
Re-uses the same body for suspend/resume and suspend/disable/resume
for DUT with a parameter to toggle disabling BT.
Re-uses the same Tester config in both existing test-cases as the
previous configs were duplicates.
Updates the dut suspension status in the message handler.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Extracts logic related to waiting for packets from
`test_advertiser.c` and `test_beacon.c` to use in a sync mechanism.
Introduces a sync mechanism in bsim with the functions
`bt_mesh_test_send_over_adv` and `bt_mesh_test_wait_for_packet`
Extracts gatt-related logic from `test_advertiser.c` into a separate
file so it can be re-used.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Emitting network beacons in parallel to proxy functionality
causes collisions. The commit disables network beacons and
allows the test scenario to be more precise.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
The recommendation to have 20ms is fair for two
consecutive messages over a single bearer. When mesh
sends two messages it can be interpreted as two
bearers working in parallel. No need to keep
an artificial 20ms delay for that. Delay was
removed and all related bsim tests were fixed.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Some beacon tests have strict time conditions and depend
on randomization interval that doesn't guarantee test pass.
This change fixes strict conditions.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Adds test that verifies correct Proxy advertisement behavior for
a device where the Proxy adv requirements changes over time,
both for single and multiple subnets.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Refactors proxy advertising implementation to allow fair sharing of
advertising resources between all subnets.
In the new implementation, each subnet is agnostic to any other subnet
that might have active proxy advertisement work. When proxy
advertisement is triggered, the implementation will first check how
many subnets that has active work. If there are more than one active
subnet, a maximum timeslot will be calculated to ensure that all active
subnets get access to the medium. The implementation will then poll
the next eligible subnet for a proxy advertising request. If the
duration of this request exceeds the maximum timeslot, the duration
for the next advertisement will be set to the maximum value.
If a proxy advertisement for a subnet is interrupted by other
advertising activity, the implementation will now ensure that the
interrupted proxy adv continues from the point where it was
interrupted so that the subnet gets to utilize the entire allocated
timeslot.
This PR also alters the priv_proxy_net_id_multi Bsim test to align
with the refactored proxy advertising scheme.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
The section 3.7.3.1 of the mesh specification recommends to delay
a message publication in certain cases:
- at power-up or upon state change for a time between 20 to 500 ms
- for periodic publications for a time between 20 to 50 ms
This change implements this recommendation by adding the
`CONFIG_BT_MESH_DELAYABLE_PUBLICATION` Kconfig option which enables
the randomization code and by adding the `bt_mesh_model_pub.delayable`
bit field which allows each model decide whether the publications
should be delayed for this model or not.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Renames "prov device" references and options to
"provisionee" to align implementation with Mesh
Protocol specification v1.1, section 5.4.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Adapts the `pb_remote_timeout` test to the updated `bt_mesh_suspend`
API.
Suspension is scheduled with a small delay to allow publications to be
sent before suspending Mesh.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Adds two test-cases; one for suspending and resuming Mesh,
and one for suspending Mesh and disabling Bluetooth before
re-enabling Bluetooth and resuming Mesh.
Both tests checks that periodic publication is stopped during
suspension.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
SIG has changed Bluetooth mesh to Bluetooth Mesh
Updating zephyr docs accordingly
Leaving out old release notes
Signed-off-by: Mia Koen <mia.koen@nordicsemi.no>
The Private Beacon Client API requires a response argument to allow to
call the API in the asynchronous manner
(https://github.com/zephyrproject-rtos/zephyr/pull/56426).
Because the removal of the EXPERIMENTAL tag for this API was not
released yet, it should be OK to change this API.
The EXPERIMENTAL tag has been removed here:
https://github.com/zephyrproject-rtos/zephyr/pull/64866
Coverity-CID: 330039
Coverity-CID: 330029
Coverity-CID: 329977
Fixes#65336Fixes#65338Fixes#65354
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
the reason is that the Mesh Profile clearly stipulates that Mesh nodes
cannot change their own element definitions.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Since model struct most of member should not change at run time,
so mark as const will be suitable and safely.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
This is to increase probability of reception of responses (Config Status
messages) from the node when the provisioner sends a Set message and the
node response with a Status message at the same time so that the message
collide.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
PR allows to get rid of tinycrypt objects from
the final binary of the ble mesh apps based on
PSA TFM crypto.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Adds coexistence Bsim test for Opcode Aggregator models using loopback.
The test verifies that the Opcode Aggregator server and client can send
messages to each other on the loopback interface.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Adds coexistence Bsim test for Opcode Aggregator models.
The test verifies that the Opcode Aggregator server and client can be
present and functional when operating on the same device.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Adds Bsim test that verifies private beacon cache functionality.
The test checks that replays of the same private beacon
message is discarded.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Adds Bsim test that verifies SNB cache functionality.
The test checks that replays of the same SNB
message is discarded.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
This is to increase probability of reception of responses (Config Status
messages) from the node when the provisioner sends a Set message and the
node response with a Status message at the same time so that the message
collide.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Since notice that simultaneous advertising is not only used
by relay message, provision over pb-adv can also be used.
so it was changed to a more general name.
refs:https://github.com/zephyrproject-rtos/zephyr/pull/48903
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
In 'test_access.c', model 3 on element 1 extending model 3 on element 0
is now registered correctly. When calling 'bt_mesh_model_extend' on
models on different elements, this needs to called from the
model with the highest element index to be registered correctly.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Adds bsim test to verify that composition data page 1 (CDP1) is
encoded and decoded correctly.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
