Overlapping Feature Exchange requested by host with
Encryption Setup requested by the application caused the
controller to corrupt its Tx queue leading to Tx Ctrl PDU
buffers from leaking from the system.
Fixes#21299.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix leak of the node_rx buffer when processing the LL version ind as a
priority event. This leak meant being able to establish new connections
was no longer possible, because there weren't enough events to process
the all the events during connection establishment. And instead the LL
ignored the connection request sent by the peer.
Removed the inline extern declaration of a function which had a proper
header included.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This documents the special cases where -EAGAIN is returned which leads
the buffer to be queued.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Now that bt_l2cap_send_cb can fail the buffer state needs to be save
and restored otherwise the data stored on it would be lost.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This introduces BT_L2CAP_STATUS_SHUTDOWN which is used to indicate when
a channel has been shutdown.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This offloads the processing of tx_queue to a work so the callbacks
calling resume don't start sending packets directly which can cause
stack overflow.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Drop packets received while disconnecting since they would most likely
be flushed once peer respond there is no gain in keeping them on a
queue.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This prevents disconnect request packets to not being sent due to lack
of buffers normally caused by flooding or congestion.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If NET_L2_BT is enabled we need enough acl_in_pool needs to be big
enough to contain a full IP packet since that is no longer processed by
RX thread buffer would be queued to syswq to reassemble the SDU.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When NET_L2_BT the memory pressure for fragments can be quite high
since that would be transfering IP packets which are considerable big
so this makes our frag_pool to be of the same size as NET_BUF_TX_COUNT.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enable chaning the function and line number making it easier to
debug where a buffer allocation is blocking.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When a segment could not be allocated it should be possible to resume
sending it later once previous segments complete, the only exception is
when there is no previous activity and we are unable to alocate even the
very first segment which should indicate to the caller that it would
block since that only happens on syswq the caller might need to defer to
another thread or resubmit the work.
Fixes#20640
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add command to print all existing connections. Useful for verifying that
connections are actually released when debugging.
More information can be retrieved with `bt info <addr>` using the
address printed by this command for each connection.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add command to print all existing bonds. Useful for verifying that bonds
are actually cleared when debugging.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix implementation for the missing reset of version
information procedure request state value.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The whitelist API uses the controller directly through HCI commands.
Bluetooth device must have been initialized before sending HCI commands.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move invalidation of connection handle when flushing TX buffers into
LLL context. Otherwise, LLL may or may not see invalidated handle
depending on mayfly scheduling.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
If the duration to publish is roughly the same as the period, we might
end up with elapsed == period, which returns 0 and cancel the periodic
publication. Instead 1 should be returned, just like when the elapsed
time is greater than the period.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Unifies the Mesh CCM implementation parts for encryption and decryption
into a crypt and an auth step, reducing stack usage and code size.
This change also brings several performance improvements, most notably
reducing copying of the nonce and unrolling the 16 byte XOR operations.
Performance for the Mesh worst case of a 382 byte payload with 16 bytes
of additional data (full transport encrypt with virtual address) goes
from an average of 889us to 780us on nRF52840 with default optimization
flags.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Handle invalid ACL flags in HCI transport.
Only Point to Point is supported over HCI in both directions.
Fix flushable start HCI ACL packets not allowed on LE-U connections
from Host to controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
In bt_l2cap_br_chan, rx.cid is the local cid and tx.cid is the
remote cid. According to Core-5.0 Vol3.Part A 4.6-4.7,
l2cap_br_remove_tx_cid should be searched using tx.cid
Signed-off-by: ZhongYao Luo <LuoZhongYao@gmail.com>
According to BT Spec v5.1 Vol 2 Part E Section 7.8.16, if the
device is already in the White List, the controller should not
add the device to the White List and should return success.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
According to BT Spec v5.1 Vol 2 Part E Section 7.8.16, if the
device is already in the White List, the controller should not
add the device to the White List and should return success.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If the whitelist already exists in the controller then the controller
should not add the device tot the whitelist and should return success.
In that case the counting of entries in the whitelist in the host will
be wrong.
Remove all whitelist counting in the host, and instead rely on the error
reported by the controller for this.
The controller should return error if the whitelist is full.
The controller should return error if use of whitelist was requested but
the whitelist was empty.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When Friend node tries to send Friend Clear message to other
Friend nodes, it should use the subnet information based on
the net_idx from friendship.
Fixes#21165
Signed-off-by: Maximus Liu <maximus.liu@gmail.com>
Expose the bt_uuid_to_str function as an API to the application.
This aligns this function with the bt_addr_to_str function call. This
allows the application to use this function without having to enable
the BT_DEBUG option.
Move the in-place bt_uuid_str to internal logging, this is mainly done
due to the limitation in the log_strdup that shouldn't be exposed to the
application.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Check that the bluetooth device has in fact been initialized before
continuing with public API calls. This could lead to crashes when using
state that has not yet been initialized.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When set, the BT_GATT_SUBSCRIBE_FLAG_NO_RESUB flag indicates that the
subscription should not be renewed when reconnecting with the server.
This is useful if the application layer knows that the GATT server
persists subscription information.
Signed-off-by: François Delawarde <fnde@oticon.com>
Added configuration for accepting pairing requests only if both devices
has bonding flag set in order to reject other devices at an early stage,
thus leaving more chance for devices expected to bond.
With the CONFIG_BT_BONDING_REQUIRED flag the device only accept pairing
requests if it has CONFIG_BT_BONMDABLE set and the device requesting
pairing has Bonding_Flags field set to Bonding (0x01) in its AuthReq.
Note: When using bt_set_bondable(false) pairing requests will be
rejected when CONFIG_BT_BONDING_REQUIRED is set.
Signed-off-by: Martin Rieva <mrrv@demant.com>
Fix issues that surfaced when trying out GCC 9.2, official release name
gcc-arm-none-eabi-9-2019-q4-major, both related to invalid pointers in
GATT when declaring UUIDs in if-scope.
1. Fix the discovery callback giving an invalid pointer in the discovery
callback in two instances.
2. Fix gatt_find_type sending invalid data during discovery procedure.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Send connection parameter update request only if it contains the valid
range of values for connection intervals, latency and timeout.
Signed-off-by: Kiran Paramaswaran <kipm@oticon.com>
Fix ATT MTU size of length variables resulting in wrong length values
reported to the user. Communicating with an Android device using an MTU
of 517 resulted in write commands reported as length 2 instead.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Since bt_conn_send_cb can fail to send buffer causing it to unref this
may cause buffer leaks as the caller is not aware of the error assuming
the buffer could be sent.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for Zero Latency IRQs, which avoids any Zephyr
OS or application influenced ISR latencies on the
controller's ISRs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Processing of data received on dynamic channels is still done via syswq
so the buffer shall not be unrefed when they are queued.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
