The data is in a net_buf already so we can just pass this to the
deserialization code. The net_buf context and API helps simplify the
code quite a lot.
Change-Id: Iecb62d3151d229a09538ad652508f1eb9c6c3ffc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Applications may want to fine-tune the stack size of the fiber that's
used to make callbacks into the application.
Change-Id: I2cd3e79283fe85359389528e84d9bcc21e3e19f6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Don't require being able to read the full header in a single ISR call.
Instead track the number of received header bytes. Also check for IPC
length before allocating buffer to avoid unnecessary buffer
allocations.
Change-Id: I1678c3ac3aaf35a1b9bbe930cc2e942fce3f458a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This allows to decrease number debug messages using config option.
Change-Id: I987d25c6d4b18503d6beb7feab97e9207100323d
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
We can take advantage of the net_buf headroom. At the same time move
the necessary definition straight into uart.c and remove any unused
definitions.
Change-Id: I932bba2cfb11808aabce7bad09e41f94d073bb5b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using net_buf helps us remove a lot of the pointer & data length
book-keeping variables and in general makes the code more readable.
Change-Id: Iec870a3bacbb63b55329ef5214b0ee0a757f5b1e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove not used code and decrease number of log messages
Change-Id: I3a41fcc15d7f7b7e8802a13f6eb871794437a87c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
With peripheral application there is at least 6 commands sent in a row
which will lead to 6 responses which might cause the driver to run out
of buffers so this increases it to 8 to align with HCI driver.
Change-Id: I7ecbc2cfbaf754c35466c57124ff87d27766a07b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since application callbacks happen from the rx thread we cannot have
the stack as small as just 256 bytes. Make it 2kB for now, but later
this needs to be adjusted to some reasonable minimum with the help of
the stack analysis code, and then probably accompanied by a Kconfig
option for apps to increase if if needed.
Change-Id: Ie8e2ac41701101b874378ded1435a6fb06bae497
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixes some styles and removes p_buf from debug log.
Change-Id: I861c2c250d8478353f8272e9c59c06f9fc211036
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This is the MTU supported by the firmware and is necessary in order to
register bigger services such as vendor specific in the peripheral
sample.
Change-Id: I24b2f9e983d8e2da22d41a40f538f0daf7d526d0
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There are situations when nble_read() might stuck reading from UART when
there is no data. Limit number of tries to 10.
Change-Id: I23380b622439ce9fa72b05f4eb527f03c749fce8
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This lowers the chance of running out of buffers when sending or
receiving a lot of data.
Change-Id: Ifedc5652f993fa54f7aded87aef545ffb49e7581
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The RPC code is not net_buf aware so it will not update the net_buf
length when encoding data into it. We have to therefore do it
ourselves.
Change-Id: I7d7d3c09007a2a9bce822625607dbf7470a7ea0b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move receiving logic to fiber rx_fiber(). rx_queue is registered with
uart driver and all data is sent there for processing. Clean up old
ipc_channel interface since there will be only one interface to uart
driver.
Change-Id: I292863b1f38e5adb8ca4e6ac63aed09c83de56bf
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Adds basic support for communication with Nordic BLE (NBLE) chip
connected to UART.
Change-Id: I3651e291ec18805a63ecd3d240dce62273e3c498
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
