PA11 can be remapped to PA9 by using the recently introduced
remap-pa11-as-pa9 property.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32G0/F0 SoCs allow to remap PA11/12 to PA9/10. Some boards
were manually configuring this remap. This patch centralizes this
functionality to the pinmux driver, allowing boards to enable the
remap directly in board dts file.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add specific properties to enable remap for PA11/PA12, which is a
possibility on STM32G0/F0 SoCs.
These properties only have effect when defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide power modes implementation for u5 socs.
For now STOP3 mode is not implemented as this mode is not
compatible with LPTIM activation and hence cannot be used
as a workable suspend to idle state using LPTIM as kernel
tick source.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When existing stop mode 1&2, VCO is set to range 4
and should be set back to range 1 to allow full speed
operations.
Rather than setting VCO at startup, set it inside clock
setting procedure so that it could done
in clock reset procedure when existing stop modes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable i2c1 and i2c2 nodes on b_u585i_iot02a.
i2c1 is used as Arduino I2C
i2c2 is used as bus for HTS221 MEMS device.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This changes is an adaptation for the different boards
based on the SOC_STM32F412ZG that has been redifined
to SOC_STM32F412ZX
Signed-off-by: Francois Ramu <francois.ramu@st.com>
A new stm32f412vx devices is introduced.
The soc devices stm32f412cx, stm32f412vx, stm32f412zx are
removed to have a more generic stm32f412xx Kconfig.
The stm32cube modules stm32f412cx/vx/zx exists.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove CC1200 and CC2520 devicetree nodes from the test as they are not
sensors and are not being built by this test regardless.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Adds build_all for ieee802154 drivers. A substantial number of drivers
are for SoC peripherals, so test cases are required many boards.
Fixes#11519.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Devices need to be resumed in the reverse order they are suspended.
e.g: devA +---> devB ---> devD
|
+---> devC
They are initialized in the following order, devA -> devB -> devC ->
devD, and suspended starting from the end of the list, devD -> devC ->
devB -> devA. When they are suspended they are temporary put in a list
that is used later to resume them.
This list has to be iterated from the end to the beginning, otherwise a
device may be resumed before its parent.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Remove two unused files that were left floating around when the
build_all sample was split up.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This updates Mbed TLS to 3.0 as well as trusted-firmware-m and mcuboot
to versions that also support this version.
Signed-off-by: David Brown <david.brown@linaro.org>
Mbed TLS 3.0 changes the configuration defines used to determine the
buffer size used for TLS. We were still setting the old one, which was
causing Mbed TLS to revert back to the large default buffer size. Set
both the in and out buffer sizes to match the config setting. A future
improvement may be to separate this into two configurations within the
Zephyr config.
Signed-off-by: David Brown <david.brown@linaro.org>
The psa-arch-tests project changed how third-party toolchains are
integrated. This broke the Zephyr sdk.
This patch aligns with the new mechanism.
https://github.com/ARM-software/psa-arch-tests/pull/276
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Mbed TLS 3.0 removes the definition for MBED_ERR_SSL_PEER_VERIFY_FAILED,
since non of its code ever returns that value. Since there isn't really
a perfect response, instead return a somewhat generic response
indicating this was unexpected.
Signed-off-by: David Brown <david.brown@linaro.org>
Moving to Mbed TLS 3.0 changes some of the Mbed TLS to better match the
PSA spec. Fix up the things where we are affected by these API changes.
Signed-off-by: David Brown <david.brown@linaro.org>
z_impl_sys_csrand_get is implement if the system is build with either
CONFIG_CTR_DRBG_CSPRNG_GENERATOR or CONFIG_HARDWARE_DEVICE_CS_GENERATOR.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Several fields of structures in mbedTLS 3.0 are now private. To access
them directly is necessary to define MBEDTLS_ALLOW_PRIVATE_ACCESS.
That is a temporary fix, the proper solution is not access directly
but using proper API.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Apply the modifications required by the newer library version.
These modifications came from the original file in the mbedTLS
repository.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Apply the modifications required by the newer library version.
These modifications came from the original file in the mbedTLS
repository.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Render Zephyr version in both, standalone Doxygen build and Sphinx
controlled build. In standalone mode, the package version given by
find_package(Zephyr...) is used, while in Sphinx build the conf.py
version is used.
The project brief has been shortened to make project title more compact
while still containing relevant information.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use the doxygen-awesome theme to improve the look and feel of the
Doxygen API documentation.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The mheap parameter documentation was missing for sys_multi_heap_fn_t.
This generates warnings on Doxygen 1.9.1.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Upgrade to Doxygen version 1.9.1. Package is downloaded directly from
the Doxygen official site, since it is not yet part of the latest Ubuntu
LTS. Note that libclang1-9 and libclang-cpp9 are runtime dependencies
required by Doxygen.
NOTE: Documentation can still be built with older Doxygen versions (e.g.
1.8.17 shipped with latest Ubuntu LTS), however, the template used in
upcoming patches claims to work better with Doxygen 1.9.1 or 1.9.2.
Using 1.9.1 as theme v1.6.0 has some issues on mobile view when using
Doxygen 1.9.2, see
https://github.com/jothepro/doxygen-awesome-css/issues/47.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The assert log of z_priv_stacks_ram_start failed to build due to passing
&z_priv_stacks_ram_start instead of just z_priv_stacks_ram_start.
Fixes#39190
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The mimxrt10xx evaluation boards that support the NXP USDHC IP
communicate unreliably with SD cards at 1.8V using the USDHC driver.
This commit temporarily disables 1.8V communication for all rt10xx
boards that currently support the USDHC driver.
Fixes#32289
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a reference to the README and the folder itself from the modules
page. This is a more permanent alternative to using
ZEPHYR_EXTRA_MODULES for west users, so it logically belongs here.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Import any manifest files in a new 'submanifests' directory into
west.yml.
This lets users define custom zephyr modules or easily override
built-in modules by dropping their own manifest files into
submanifests/some-user-file.yaml.
Provide an example and a README with links to the relevant
documentation in 'submanifests' to get users started.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This name should be the same as cpus node in dtsi. After the power
policy is added, the cpu-power-states in the CPU properties can
be used.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Documents significant changes to sensor drivers in the v2.7.0 release,
including new drivers added and existing drivers modified.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Fixes#38994, ARP messages were being sent to IPvXmcast MAC addresses
rather than the expected source MAC address or the broadcast address.
Signed-off-by: Robert Melchers <rmelch@hotmail.com>
If CONFIG_WIFI_ESP_AT_SCAN_MAC_ADDRESS: mac addr included in
scanning results.
if CONFIG_WIFI_ESP_AT_SCAN_PASSIVE: passive scanning is used instead of
default active scanning.
If CONFIG_WIFI_ESP_AT_SCAN_RESULT_RSSI_ORDERED: scanning response
ordered by RSSI.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
