dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2 identical packages were defined for stm32f412 SoC, invariant "g".
Merge them in new sinclge stm32f412Xg.dtsi.
Update matching boards accordinlgy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
As explained in issue #8915 the STM32F4xx SoC family I2C
does not work well in Standard mode (100KHz). So let's
configure i2c3 in Fast mode (400KHz).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit is taking care of following stuff:
1. pinmux: STM32F4 micro is using I2S5_CK and I2S_SD to interface with
on-board microphone.
2. default configuration:
- enable I2S5 and configure PLLI2S properly to generate
I2SxCLK = 128MHz.
- enable DMA
Note:
As stated in issue #9028 we needed to take care of a known SPI/I2S bug
implementing the following two actions:
A. APB2 clock has been slowed down to 42MHz.
B. The SPI/I2S clock gpio speed has been set to very_high_speed.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch is equivalent to 7b0ce85242,
but applied to more boards. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for button nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ArgonKey board has 12 leds controlled by TI LP3943 led
controller. Add the support in the BSP.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
ArgonKey board is a 96boards sensor hub platform for all 96Boards
compliant family products. The ArgonKey packs a Cortex-M4 chip
together with a set of motion, environmental and ambiental sensors
and can be used as a development platform for many different
applications.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
