- Allows to build and run NVS tests on real platforms.
- Enables NVS tests designed for a flash-simulator only when
built for qemu_x86, mps2_an385 or native_sim targets.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Fixes the littleFS test_fs_mkfs_custom test fail
in littlefs_init_cfg(): "erase size must be multiple of write size".
It happens for platforms with erase size < 2*write size (e.g. lpc55s).
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Fixes the false negative littlefs.test_lfs_basic test that can occur
if the small_partition size > 64KB, and for
platforms with CONFIG_FS_LITTLEFS_PROG_SIZE > 64 (e.g. lpc55s, mcxn).
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Initial DAC driver for TI DAC161S997. This is a 1 channel 16 bit
DAC designed for 4-20 mA loops.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Introduce a generic reset MMIO driver to be used for devices with a
single memory mapped reset bit required to take them out of reset.
Signed-off-by: Mohith Potluri <saimohith@google.com>
The vendor prefix has been changed from 'ltr' to 'liteon'.
This change is made to better reflect the actual name of
the vendor, which is LiteOn. The previous prefix 'ltr'
was referring to the LiteOn Optical Sensor family, which
could lead to misunderstandings.
Signed-off-by: Konrad Sikora <kontakt@konradsikora.pl>
We can't do synchronous HCI command sending in any settings commit()
callback, since we don't know what context the callback is being called
from. One particular deadlock can happen if settings_load() is called from
the preemptible main thread:
main()
|--> settings_load() (aquire settings_lock mutex)
|-->commit callback A that defers to system wq
|-->commit callback B that calls bt_hci_cmd_send_sync()
system wq from the previous deferral from within settings_load():
|--> work item
|--> settings_save_one()
|--> attempt to aquire settings_lock mutex
In the above scenario, the bt_hci_cmd_send_sync() call from the main thread
depends on the system workqueue being processed (since that's what does HCI
command processing by default), while at the same time holding the settings
subsystem's mutex. At the same time, a system wq item tries to store
something into settings, however it deadlocks waiting for the settings
mutex.
The actual scenario that we have in the Bluetooth subsystem is where
"commit callback A" is commit_settings() in host/settings.c, and "commit
callback B" is keys_commit() in host/keys.c.
The solution to the deadlock is to take advantage of deferred bt_id_add()
handling which already exists, i.e. set a flag and deferre the actual
adding to the system workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
If the HCI status of a complete event is not BT_HCI_ERR_SUCCESS,
the remaining parameters could be invalid.
In this case, the params is passed as NULL pointer to the callbacks.
- LE CS Read Remote Supported Capabilities Complete event
- LE CS Read Remote FAE Table Complete event
- LE CS Config Complete event
- LE CS Security Enable Complete event
- LE CS Procedure Enable Complete event
This change avoids forwarding the invalid fileds to the applications.
Signed-off-by: Ryan Chu <ryan.chu@nordicsemi.no>
As there is no currently known board that has the cadence spi,
add a test to just build it under the qemu cortex m3.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
When building with clang, it warns:
tests/subsys/usb/bos/src/test_bos.c:24:22: error: variable
'dummy_descriptor' is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
static const uint8_t dummy_descriptor[] = {
^
Only the size of dummy_descriptor is used, not the contents. Replace the
struct with a constant for the size.
Signed-off-by: Tom Hughes <tomhughes@chromium.org>
- Reduces the ram disc sector count from 400 to 220.
- Saves about 90KB of RAM. All tests still passed.
- Allows platforms with less RAM to run
the ramdisc_small.overlay test.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
There are a couple things going wrong in this test code right now.
First of all, there is no syncrhonization of when the async polling
thread should start polling, causing sometimes the poll to fail on tests
before the async test ran. Add a semaphore to fix this.
The lock test was setting up a nonsense NOP transfer of 0 length.
This might cause unexpected behavior and is not the point of
this test case.
But, still we should add a seperate test case specifically for
testing this instead.
Also add a teardown function to release the locks to allow other test
cases to run in case of some failures.
Also a minor change to remove some ARG_UNUSED invocations for some
arguments that are actually used.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Fixes typo in the event name.
Changes the struct to also use _ev instead of _rp as it
is an event and not a response.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Commit fixes bug when corresponding group ID was never
incremented for independent corresponding relationships.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Add checks that we will be able to catch invalid compression bit in
response CNAME handling.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add checks that we will be able to catch recursive name pointers and
abandon the response for CNAME handling.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Test was occasionally failing when two types of current time
reading occurred at different system tick. In that case they
were of by one system tick and test was failing.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add a memory barrier to make sure write to NVIC is completed
before continuing with the test fails in scenarios where
CONFIG_ROMSTART_RELOCATION_ROM is enabled for boards like MPS3
Corstone310 and k_sem_take is called before the isr's are called.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Enable tests by default for CS300 and CS310 since they support
simulation and FVP's are available in upstream docker.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Change default pwm to pwm0 on ek_ra6m3 in test app pwm_loopback
to avoid pin conflict with ethernet phy.
Signed-off-by: Ta Minh Nhat <nhat-minh.ta.yn@bp.renesas.com>
This patch allows checking for any custom ARM interrupt controller to get a
non-enabled IRQ line instead of assuming that GIC is enabled
Signed-off-by: Amneesh Singh <a-singh7@ti.com>
As above, the test verify the ability to wake up CPU
from the lowest power state. The test has been
prepared for stm32l562e_dk board.
Signed-off-by: Arkadiusz Cholewinski <arkadiuszx.cholewinski@intel.com>
This test evaluates the residency time of different power states
on the stm32l562e_dk board and calculates the
RMS (Root Mean Square) current for every detected state.
Signed-off-by: Arkadiusz Cholewinski <arkadiuszx.cholewinski@intel.com>
During the test, pytest detects each step and calculates
the RMS (Root Mean Square) current for every detected state.
The test then compares the calculated RMS values
against the expected values.
Signed-off-by: Arkadiusz Cholewinski <arkadiuszx.cholewinski@intel.com>
Providing the right config options and a new test scenario,
coredump_backends test will run under the in-memory backend.
Signed-off-by: Tomasz Bursztyka <tobu@bang-olufsen.dk>
Fix incorrect CIS offset in use if instant is picked from
the peer sent CIS RSP PDU. Instead, keep the instant that
was sent in the CIS REQ PDU as the instant to send in the
CIS IND PDU.
This fixes CIS failed to be established when dissimilar
ACL and ISO intervals are in use.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This test is being skipped for the last 3 years, had lots of issues when
it was introduced. No need to keep it in the tree.
If fixed and made to work again, we can always add it back.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Few tests are being skipped for no goot reason (anymore). Add some
coverage using few platforms that work with intention to expand if all
works well and if needed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some platforms were excluded due to issues that were fixed or resolved
themselves. Enable those platforms again and remove the comments related
to the issues.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If CONFIG_NET_DHCPV4_OPTION_PRINT_IGNORED is set, then adjust the
tests as we no longer get so many events.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Currently we ignore the broadcast address but make sure we
print it in order to avoid unknown option prints.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Test was assuming that CONFIG_SYS_CLOCK_TICKS_PER_SEC=100 but such
frequency is not well supported on SoC which are based on 32768 Hz RTC
clock. Align test to be able to work with different sys_clock
frequency by converting previously 20 ticks to milliseconds.
Set CONFIG_SYS_CLOCK_TICKS_PER_SEC=32768 when system clock is using
Nordic RTC timer driver.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Type case CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC to uint32_t
while defining sys_clock_hw_cycles_per_sec_runtime_get()
to extend the range of frequency to 0xffffffff.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Add a dedicated "build_all" test for the NEORV32 and its peripheral
drivers. These drivers depend on the NEORV32 SYSINFO (syscon) and thus
cannot easily be built for non-NEORV32 board targets.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Use drivers.sensor for all tests related to sensors.
Also change MAINTAINER file to reflect that. It was using
drivers.sensors
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit provides an extension to the i2c_nrfx_twim driver.
It introduces possibility to acquire/release exclusive access to the
i2c bus. While the exclusive access to the i2c bus is acquired
you can access the underlying nrfx_twim driver directly.
Signed-off-by: Andrzej Kuros <andrzej.kuros@nordicsemi.no>
- Fixes the main stack overflow for the fat_fs_api
RAM disk configuration on real platforms.
- Sets CONFIG_MAIN_STACK_SIZE=3072. By default it is 1KB,
but the stack usage is about 2KB.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
QSPI NOR driver non-Quad mode was not tested before.
Add configuration that uses driver in the non-Quad mode.
Signed-off-by: Bartosz Miller <bartosz.miller@nordicsemi.no>
The MAX22199 is an IEC 61131-2 compliant industrial digital input device.
The MAX22199 translates eight 24V current-sinking industrial inputs to a
serialized SPI-compatible output that interfaces with 3V to 5.5V logic. It
can operate as eight Type 1/Type 3 digital inputs or four Type 2 digital
inputs. The device provides diagnostic functions, including thermal
shutdown, 24V under voltage alarm, 24V missing voltage alarm, and SPI and
CRC communication error detection.
Signed-off-by: Robert Budai <robert.budai@analog.com>
