Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Conditionalizes ethernet pinmuxes on CONFIG_NET_L2_ETHERNET for all nxp
boards (kinetis, lpc, and imx families) to avoid possible conflicts
between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes i2c pinmuxes on CONFIG_I2C for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes serial pinmuxes on CONFIG_SERIAL for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1020_evk
board for LPI2C1 and LPI2C4. LPI2C1 is shared between the Arduino
connector J18 and the WM8960 codec. LPI2C4 is shared between the Arduino
connector J19 and the FXOS8700CQ sensor (non-populated by default).
Updates the board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables the mcux ethernet driver and pin muxes on the mimxrt1020_evk
board, the same way it is done on the mimxrt1050_evk board. Updates the
board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables instance 2 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1020_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add board support files for mimxrt1020_evk, the development board for
i.MXRT1021 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
