The compatible: "st,stm32h7-hsi-clock" has HSI clock divider
required which is set to 1, by default, delevering 64MHz
in the stm32h7.dtsi and stm32h7rs.dtsi
(As done for stm32h5 and other series)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This makes minichlink the default runner for the ch32v003evt.
This way, `west flash` "just works", as advertised in the README, rather
than having to manually set the runner to `minichlink` for it to work.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Use the broadcast sink callbacks to set the semaphores
rather than the stream callbacks, as the broadcast sink callbacks
are better for that as they are called when all streams are ready.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Use the broadcast source callbacks to set the semaphores
rather than the stream callbacks, as the broadcast source callbacks
are better for that as they are called when all streams are ready.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
These callbacks are trigger for changes that affect the entire
broadcast sink, such as the BIG synced and terminated events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
These callbacks are trigger for changes that affect the entire
broadcast source, such as the BIG started and terminated events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
These callbacks are trigger for changes that affect the entire
broadcast source, such as the BIG started and terminated events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add callbacks that is called for the entire BIG.
The BIG state is from an HCI perspective a single state change
that we previously only propagated as a state change for each
channel.
However it may be simpler for applications and higher layers
to use BIG changes to trigger their behavior.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This fixes an issue that occurred if deferred_work is queued by another
procedure before we run bt_conn_set_state(BT_CONN_DISCONNECTED).
bt_conn_set_state yields to the system work queue in bt_conn_tx_notify,
and then deferred_work runs and handles the disconnected callbacks.
bt_conn_set_state then enqueues another deferred_work which calls the
disconnected callbacks again and causes an assert. k_work_cancel_delayable
will clear queued deferred work when we call
bt_conn_set_state(BT_CONN_DISCONNECTED), guaranteeing that the disconnect
callbacks will only be called once.
Signed-off-by: Timothy Keys <timothy.keys@nordicsemi.no>
Add set the parameter `type` to value
`BT_SDP_DISCOVER_SERVICE_SEARCH_ATTR`.
Update the SDP discovery callback function by adding a third parameter
`const struct bt_sdp_discover_params *params`. Make it align with
`bt_sdp_discover_func_t`.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Since the function `bt_sdp_discover` has been updated, the caller of
function needs to be updated to avoid the building and functionality
fault.
Add set the parameter `type` to value
`BT_SDP_DISCOVER_SERVICE_SEARCH_ATTR`.
Update the SDP discovery callback function. Make it align with
`bt_sdp_discover_func_t`.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Extend the function `bt_sdp_discover` to support service search
transaction and service attribute transaction.
Improve the `session->rec_buf`. If the net buffer cannot be allocated
from the channel, disconnect the SDP session.
Set the `MaximumAttributeByteCount` of the request
`SDP_SERVICE_SEARCH_ATTR_REQ` with the tail room of `session->rec_buf`.
Set the `MaximumAttributeByteCount` of the request `SDP_SERVICE_ATTR_REQ`
with the tail room of `session->rec_buf`.
Set the `MaximumServiceRecordCount` of the request
`SDP_SERVICE_SEARCH_REQ` according to the tail room of
`session->rec_buf`.
Handle the response code `SDP_SERVICE_SEARCH_RSP`, and
`SDP_SERVICE_ATTR_RSP`.
Handle the error `SDP_ERROR_RSP`. Start the next SDP discovery if the
error received.
If there no more request, disconnect the session.
If the request cannot be sent, start the next SDP discovery.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
On RT1180/RT700, there is no gpr register on soc,
so change driver to get configuration register base
address from dts, instead of hard code.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
Deprecate mode which is using TIMER+(D)PPI for reliable byte counting.
Recently a new approach is added (CONFIG_UART_NRFX_UARTE_ENHANCED_RX)
which supports reliable byte counting without additional HW resource.
This mode is planned to be the only supported RX path mode.
Enhanced RX has slightly different behavior. There are no partial RX
packets (events with non-zero offset). There is UART_RX_BUF_RELEASED
after each UART_RX_RDY event.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Due to clock designed on RT1180 has some different with other platforms,
so add macro and handle the clock difference in mcux_ccm_get_subsys_rate.
TPM1 use Bus_Aon as clock root.
TPM3 use Bus_Wakeup as clock root.
Other instances have independent clock root.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
The PINCTRL option is selected now by the drivers which use it, so
it's possible to remove it from the board defconfig.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
- Add NULL checks for broadcast_source_stop
- Add NULL checks for broadcast_source_release
- Return -ESRCH if trying to stop ext_adv before creation
Signed-off-by: Alexander Svensen <alexander.svensen@nordicsemi.no>
The Smartbond SPI driver enables DMA acceleration by default. However
no DMA configuration is provided in the SPI node, resulting in run
time errors when the SPI interface is used. Instead, the application
should explicitly enable DMA acceleration and select the DMA channels
and priorities.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Updating the LPADC driver to support IP without a side B channel.
The MCXA156 is an example with this instantiation of the IP.
Signed-off-by: Neil Chen <cheng.chen_1@nxp.com>
The pthread_pressure test was not a typical test per se. It was
a benchmark in search of the proper home.
Let's move it to the correct place in the Zephyr tree, add a
doc, and provide some reporting.
Currently, k_threads out-perform pthreads by almost a factor of
2. The theoretical maximum performance of pthreads would be at
parity of k_threads, since pthreads are a wrapper around kernel
threads. It would be great to reduce the gap.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Fixes type mix-match for rtd temperature calculation. Also changes
coefficient array name for clarity.
Signed-off-by: Maxmillion McLaughlin <max@sorcerer.earth>
Commit 132fa83ed4 ("arch: riscv: make arch_current_thread_set()
safer") created some unintended code generation changes. Reorder the
assignments to preserve original results.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
For WiFi interface, uniformly use net_if_get_wifi_sta() and
net_if_get_wifi_sap() APIs to replace net_if_get_first_wifi().
Signed-off-by: Gang Li <gang.li_1@nxp.com>
Add documentation for the get_filtered_output method in both the Python
implementation and the Integration with pytest chapter. The method is used
to filter command outputs by removing prompts and log messages, making it
easier to process shell command results.
Signed-off-by: Thomas Günther <thomas.guenther@limatica.com>
removed traling whitespace
Add a new implementation of a test pattern generator, with the same
architecture as real drivers: split receiver core and
I2C-controlled sub-device, with changes of video format in
"zephyr,emul-imager" leads to different data produced by
"zephyr,emul-rx".
Signed-off-by: Josuah Demangeon <me@josuah.net>
Introduce a video_get_format_index() utility to help finding a caps
entry out of a given format. Introduce several utilities to seek and
apply frame intervals.
Signed-off-by: Josuah Demangeon <me@josuah.net>
STM32 configuration for the MCO clock source and prescaler is done
by the DTS and no more by Kconfig (removed).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
