Add pa variant definition to board.yml
Add bl654_dvk_nrf52840_pa files dts, yaml, defconfig
Update doc with information on variant and regulatory information
Signed-off-by: Jate Sujjavanich <jatedev@gmail.com>
Add SWD debugger support for this board. Although there is not a debug
header, the SWD pins are accessible and the adaptor is not that difficult
to wire up. This will allow for debugging beyond just flashing, that the
UF2 programming setup allows for.
Signed-off-by: David Brown <david.brown@linaro.org>
In preparation for adding AMP support for i.MX RT6xx family we need
to rename existing cm33 support files to more specific names.
e.g mimxrt685_evk.dts -> mimxrt685_evk_mimxrt685s_cm33.dts
This will allow us to later add support for Cadence DSP found on i.MX
RT6xx series.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
imxrt6xx are dual core devices featuring an ARM Cortex-M33
core and an Cadence Xtensa HIFI4 Audio DSP.
Currently only m33 core is supported. In order to support
the Cadence DSP we need first to do some code-reorganization
for m33.
We start by moving all cm33 related code to its own directory
and introduce the cpuclusters property in soc.yml file.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Fixs USDHC by setting PWR and CD gpio's correctly.
Adds missing button from the GPS module.
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
There was missing storage partition that is required for setting
subsytem. Add missing entries to board files.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
There are default configs that are provided by default for
e.g. nRF5340dk to enable HCI IPC communication type for
application domain and enable BT controller for radio domain.
These configs were missing for nRF54h20 DK.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Explain the different versions of the MB1166 shield and
remove note about that version A09 is not supported
Signed-off-by: Erik Andersson <erian747@gmail.com>
Add support for the A09 version of MB1166 which
have a NT35510 panel controller instead of an
OTM8009a as in prior versions
Fixes#60888
Signed-off-by: Erik Andersson <erian747@gmail.com>
This commit enables PMP on the default revision of the SiFive HiFive1
board. PMP was already enabled on the Rev B of this board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Add pinctrl for SAI1 node. This means:
1) Adding definitions for the pads used by SAI1.
2) Creating a pin group and referencing it in
the SAI1 node via the `pinctrl-0` property.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add pinctrl for SAI1 node. This means:
1) Adding definitions for the pads used by SAI1.
2) Creating a pin group and referencing it in the
SAI1 node via the `pinctrl-0` property.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
On the RT1170-EVKB, the framebuffer displays incorrectly
(shifted by about 1/4 of the screen width). This is because
pixelclk-active was set to 1 (which corresponds to
kELCDIF_DriveDataOnRisingClkEdge).
According to the RM68200 datasheet, the DSI transfert begins at
the uprising pixel clock and stop at the falling pixel clock. So,
pixelclk-active needs to be set to 0 (which corresponds to
kELCDIF_DriveDataOnFallingClkEdge).
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
On the RT1170-EVKB, the framebuffer displays incorrectly
(shifted by about 1/4 of the screen width). This is because
pixelclk-active was set to 1 (which corresponds to
kELCDIF_DriveDataOnRisingClkEdge).
According to the HX8394 datasheet, the DSI transfert begins at
the uprising pixel clock and stop at the falling pixel clock. So,
pixelclk-active needs to be set to 0 (which corresponds to
kELCDIF_DriveDataOnFallingClkEdge).
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Enable clock control for i.MX8ULP. This consists of:
1) Adding a PCC node in the DTS
2) Adding a header file containing the definitions
of the clocks used by the peripherals to be enabled.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Adds the device trees, Kconfig, and documentation files.
The following features have been confirmed working on hardware:
* LED
* Button
* ST7735 TFT-LCD
* External QuadSPI NOR Flash memory
* External SPI NOR Flash memory
* USB CDC ACM
* microSD card
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
Change, for audio DSP and M7 cores, SOC_<name> to match
the exact soc name.
Update the board files accordingly.
These configs are used in SOF and NXP_HAL, so change
sha for these modules.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Adds a devicetree alias to the ambient temperature sensor on
adi_eval_adin1110ebz to support the thermometer sensor sample
application.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Source code of board/m5stack/m5stickc_plus and
board/m5stack/m5stack_atoms3_lite were adapted for an inital
support of the M5Stack ATOM Lite board.
Signed-off-by: Nikola Trifunovic <nikola@trifunovic.at>
In future versions of Linkserver, specifying the core argument within
the device string will not be supported. Therefore, move the FRDM
MCXN947 board to specify the core directly instead of using the device
string.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
- fix schematic link pointing to different board
- fix link to the board_defconfig file
- remove the "Debug Firmware" link that was not referenced anywhere
- add a link to the board user manual
- minor additions to the debug with J-Link section
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Create regulator on GPIO for microphone supply
Set pdm data and clk pins in pinctrl
Add xiao_ble_sense overlay for dmic sample support
Signed-off-by: Zak Portnoy <zakportnoy@gmail.com>
Enable DMIC on RW612 BGA board. The DMIC is enabled for both onboard
MEMS microphones for this board, and the board is enabled with the DMIC
sample and test
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Set the PLL1_Q divider to 6 give a can core clock of 80MHz to
resolve fdcan_clk reception problem because M_CAN requires that
the host clock "APB1" should be higher or equal to the CAN core
clock "PLL1_Q".
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
Add necessary overlay and stm32h573i_dk in i2c_target_api test case
to enable the board.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
The SOC name for the `imx8ulp_evk` board has been changed
to `mimx8ud7`. As such, update `deprecated.cmake` to reflect
this change.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
The SOC name `imx8ulp` has been just a placeholder until
support for the SOC's ADSP (since this is the only core
that's supported in Zephyr) could be added to the NXP HAL.
Now that the support has been added, to make use of it, the
SOC name `imx8ulp` has to be changed to `mimx8ud7`. As such,
this commit does the following:
1) Introduces SOC part number configuration - needed
by some HAL headers.
2) Replaces all occurrences of `imx8ulp` (as the SOC
name) with `mimx8ud7`.
3) Enables `CONFIG_HAS_MCUX`.
4) Aligns all `CONFIG_SOC_` configurations with the
new SOC name.
5) Updates SOF hash. This is needed to fix build issues
caused by this name change. This is not done in a separate
commit to preserve bisectability.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This commit should fix configuration conflicts that
came up upon merging both MIPI DBI and display panel
drivers.
1. Board's display/LVGL Kconfigs should be enabled when
needed based on the selected display interface.
2. Overwrite the touch controller's I2C pins to avoid
conflicts with the display panel signals.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
To use this functionality one must now use the native_sim//64
(variant) version. The old hwmv1 compatible name for the board
was left provisionally while all tests in tree were ported.
That being now done, this old name can be removed.
After this change one cannot build anymore
targeting native_sim_64, but must instead build
targeting native_sim/[native]/64.
For twister tests the old name is already not valid.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
To use this functionality one must now use the native_posix//64
(variant) version. The old hwmv1 compatible name for the board
was left provisionally while all tests in tree were ported.
That being now done, this old name can be removed.
After this change one cannot build anymore
targeting native_posix_64, but must instead build
targeting native_posix/[native]/64.
For twister tests the old name is already not valid.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add devicetree node for the accompanying, ssd1306-based display board
connected to connector P4.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Correct a few issues with the documentation that were causing rendering
issues, as well as the following changes:
- added blurb to debug section clarifying that the default debugger
firmware supports LinkServer
- updated serial terminal output with board name given when building
with HWMv2
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
By default, LinkServer's memory map for the MCXN947 does not define
memory regions for the SRAM or peripheral bus in secure mode. This
results in gdb failing to read from these memory regions unless
explicitly told ignore the debugger memory map via
"set mem inaccessible-by-default off".
To resolve this, define memory regions for SRAM and peripherals in
secure mode via the commandline arguments passed to LinkServer in
board.cmake.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
To use this functionality one must now use the hwmv2 naming
(nrf5340bsim/nrf5340/cpu{app,net}).
The old hwmv1 compatible names for these targets,
were left provisionally while all tests in tree were ported.
That being now done, these old names can be removed.
After this change one cannot build anymore
targeting nrf5340bsim_nrf5340_cpu{app,net}
but must instead build targeting
nrf5340bsim/nrf5340/cpu{app,net}
For twister tests the old name were already not valid.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This patch fixes a broken link in the docs for the
nrf9151dk.
It points to the SiP's product page for now.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
