Values to be set to the comparator need to be specified in RTC cycles,
not ticks, so the initial value used in the tickless mode needs to be
MAX_CYCLES, otherwise when CONFIG_SYS_CLOCK_TICKS_PER_SEC is set to
a value less then the RTC frequency, the initially configured timeout
will be unnecessarily shorter.
On the occassion, remove also the call to counter() when setting the
initial timeout value in non-tickless mode. RTC is cleared a few lines
above, so at this point it will most likely be 0, and even if it was
not, compare_set() would properly handle a target time value that had
already passed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In non-tickless mode, the timeout handler always announced maximum 1
tick to kernel, but in fact it cannot be guaranteed that the handler
execution is not delayed and that the number of elapsed ticks does not
exceed 1. Use the actual number instead.
Switch also to using a 32-bit value for `dticks` to get a bit simpler
generated code (ticks delta is not supposed to be that huge).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Align the condition checked in compare_set_no_locks() with what
set_absolute_alarm() actually provides (and slightly correct the
latter function so that it provides what it is supposed to).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add missing masking against `BIT(chan)` when handling a forced ISR
to avoid unnecessary processing of multiple channels instead of just
the one that actually requires it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove a piece of code that was supposed to bring an extra update
of the anchor value but which in fact was not able to provide it,
because of the target time checking performed in process_channel(),
and which is anyway unnecessary because the timeout span is limited
to MAX_CYCLES in sys_clock_set_timeout(), so the timeout handler is
guaranteed to be executed at least twice per each RTC overflow.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Eliminate waiting for a potential COMPARE event when setting a CC
value close to the previously set one and rely instead on checking
target time when processing channel events in the ISR.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove unnecessary decreasing of the number of ticks by 1 (it was then
increased by 1 when it was converted to the number of cycles) and add
a comment that clarifies the way that ticks < 1 are handled.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adding PWM support for the center RGB LED to allow for
fancy disco lights, suitable for an audio development kit.
Signed-off-by: Lars Knudsen <larsgk@gmail.com>
Add BT_AUDIO_CONTEXT_TYPE_UNSPECIFIED as the default supported
context. This is primarily due to the requirement that it
shall always be supported, and the value 0 (previous
default) was invalid.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The call to set_supported_contexts in set_src_supported_contexts
gave the wrong value by reference.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Unit test project for bt_le_oob_get_sc_data().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_le_oob_set_sc_data().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_le_oob_set_legacy_tk().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_le_ext_adv_oob_get_local().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_le_oob_get_local().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
# Conflicts:
# tests/bluetooth/host/id/CMakeLists.txt
Unit test project for bt_br_oob_get_local().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_id_set_adv_own_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_id_set_scan_own_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_id_set_create_conn_own_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_id_add().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
# Conflicts:
# tests/bluetooth/host/id/CMakeLists.txt
Unit test project for bt_id_adv_random_addr_check().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_id_scan_random_addr_check().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
# Conflicts:
# tests/bluetooth/host/id/CMakeLists.txt
Unit test project for bt_id_set_adv_random_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_id_set_adv_private_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
# Conflicts:
# tests/bluetooth/host/id/mocks/adv.c
# tests/bluetooth/host/id/mocks/adv.h
Unit test project for bt_id_set_private_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
# Conflicts:
# tests/bluetooth/host/id/CMakeLists.txt
Unit test project for bt_lookup_id_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
# Conflicts:
# tests/bluetooth/host/id/CMakeLists.txt
Unit test project for bt_setup_random_id_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_setup_public_id_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
Unit test project for bt_keys_update_usage().
This part of subsys/bluetooth/host/keys.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
This sets the RNG node that will be used by the Nordic
devices which support TF-M (nRF5340/nRF9160) to use the
defined scheme with psa_generate_random.
Signed-off-by: Georgios Vasilakis <georgios.vasilakis@nordicsemi.no>
Zephyr's default settings usually enable the only minimum of peripherals,
and rpi_pico already has `i2c0` enabled.
Remove the `i2c1` node configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Fixes an issue with the documentation whereby the wrong hash/sha
sections were described, also adds a link to upstream MCUboot
documentation for further information.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
A follow up to commit 1d7a077e11 - apparently the PPP interface should
not be brought entirely down internally, as this can break further
communication with the host. Because of that, reintroduce functionality
that used to be covered by net_if_carrier_down() (which basically
skips the L2 enable(false) call), but limited to PPP scope only.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Fixes#53786
The variable slot_plus_us is assumed to be a number in us unit.
To assign the maximum possible CTE length to this variable,
BT_HCI_LE_CTE_LEN_MAX has been used while this parameter is defined
in a 8us units (it's 0x14=20 that corresponds to 160us).
To convert this number to us, it's needed to be multiplied by 8.
Signed-off-by: Saleh Mehdikhani <saleh.mehdikhani@unikie.com>
This is important for applications which are chain-loaded by a broken
bootloader which doesn't reset the peripheral before handing over control.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The documentation for the fixed-partitions binding is missing critical
information and is vague in other important respects. This is an
important binding that deserves to be crystal clear. Fix it.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
The build system currently links the toolchain-provided C++ standard
library even when the C++ support (`CONFIG_CPP`) is not enabled.
This commit updates the build system to link the toolchain-provided C++
standard library when the C++ support is enabled and a C++ library
implementation other than the Zephyr minimal C++ library is selected.
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
The bt_has_register_param's preset_sync_support and independent_presets
make sense only if CONFIG_BT_HAS_PRESET_COUNT is non-zero meaning the
CONFIG_BT_HAS_PRESET_SUPPORT is enabled.
Otherwise, those parameters shall be skipped.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
