Add missing interrupts property for second FlexSPI device on RT5xx.
This interrupt is shared between both FlexSPI devices, but the memc
driver does not use interrupts so no conflict should arise.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for APS6408L PSRAM, built on top of the MCUX memc
driver for flexSPI. This driver supports operating the PSRAM in high
speed mode (200MHz or more). Note that in order to support this
PSRAM's alignment requirements, either ahb-read-addr-opt or
ahb-prefetch must be set for the FlexSPI instance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename flexspi-hyperram driver to flexspi-s27ks0641, and update
function names. This driver is only capable of supporting the
s27ks0641 HyperRAM chip, as the lookup table given in this driver
is specific to the s27ks0641.
Rename the flexspi-hyperram binding to reflect this, to
prevent confusion from users.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix all line-length errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(line-length)'
Using a limit is set to 100 columns, not touching the commandlines in
GitHub workflows (at least for now).
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all comments-indentation errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(comments-indentation)'
This checks that the comment is aligned with the content.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all hyphens errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(comments)'
Default config would be to require two spaces after the start of the
comment, proposing to keep it on 1, inline with the Linux binding
config, that is:
```
- comments:
- min-spaces-from-content: 1
```
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all hyphens errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(hyphens)'
Default config is only one space after the hyphen.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all brackets errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(brackets)'
Default config is to have no spaces inside brackets, changed few
documentation strings as well that refered to lists even though the
linter does not care about those.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The addresses of the flash and flash controller of the RP2040
SoC were mixed up. There was no clear distinction between the
flash and the flash controller, which was unclear but also
caused a DTC warning.
This commit makes the distinction clearer: The SSI peripheral at
0x18000000 is the flash controller, and the flash itself starts
at 0x10000000. The flash driver and rpi_pico.dts were fixed
accordingly.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
The pinctrl node of the RP2040 had the same unit address as the GPIO
bank, causing a DTC warning. To fix this, the pinctrl's address was
removed, as it does not require any.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Remove the test clock out Kconfig from SoC level. Instead use
device tree PINCTRL entry with updated clock control driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for Microchip MEC15xx to the XEC clock control driver.
MEC15xx 32KHz clock support uses the same 32KHz source for both the
PLL and peripherals. MEC152x does not include the PCR clock monitor
present in MEC172x. MEC15xx and MEC172x support internal silicon
oscillator, parallel and single ended crystal inputs, and the
32KHZ_PIN input. MEC152x supports fall back to internal silicon
OSC when VTR and 32KHZ_PIN are turned off. Therefore in MEC152x the
internal silicon oscillator can only be disabled if using an external
32KHz which is always on. For MEC152x the driver will only use the
PLL source clock device tree value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add initial support for gd32l23x series. gd32l23x used Cortex-M23, based
on ARMv8-M baseline, implement the System Timer.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Enable RTU.SWT (Real-Time Unit.Software Watchdog Timer) instances on
s32z270dc2_r52 boards. Module clock frequency is fixed to 48 Mhz.
Signed-off-by: Quang Bui Trong <quang.buitrong@nxp.com>
Add missing I2C clock sources for STM32F303 & F373.
Add a comment for all STM32F3 I2Cx and for STM32F0 I2C1 that the clock
source should always be defined.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add config cell property to gd,gd32-dma.
For supporting hardware variation, Splitting base definition
to gd,gd32-dma-base.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Define SYSCLK as the default I2C source clock for I2C1 on STM32F0x
and all I2Cx on STM32F3x.
On most series, the default I2C clock source (when it exists) is PCLK.
This clock does not exist as I2C clock source on FO & F3 and the default
one is HSI. Since HSI is not necessarily enabled we explicitly set it
to SYSCLK instead.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Include the new clock file dedicated for STM32F7 instead of the F4 one
previously used.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
peripheral-id property should be eventually removed.
For now set it as optional and allow skipping the usage
in UART driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
peripheral-id property should be eventually removed entirely.
For now set it as optional and allow skipping the usage
in GPIO driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
HAL update affects also EFR32MG21 SoC. Because of that we need to
update the reg addresses in DTS.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
This commit adds support for Silicon Labs EFR32BG22 SoC.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds initial support for Silabs Real-Time counter
Co-authored-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
This commit adds a series of driver-related changes to
Gecko pinctrl.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds initial support for gecko pinctrl driver
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The ADC module has four conversion groups, each one is set up as a zephyr
device. The start-up calibration is initiated globally for all groups
and it is run in each device init function. The ADC module supports post
calibration per group. Post calibration is run automatically after each
group acquires the samples.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Add virtual memory entry in dt to use as virtual space
regions for aplication.
Add virtual memory definition in adsp_memory.h
Signed-off-by: Jakub Dabek <jakub.dabek@intel.com>
Add FFF-based fake regulator driver. This driver can be used as a stub
or mock in testing.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
These inherited properties from Linux bindings are not supported yet.
The reason for the removal is because regulator-couple-with requires
definition of #cells spec, unless bindings explicitely ban the property
or use allowlist.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
