The timeout for testing advertisement extensions in babblesim
was set to 30 seconds. Depending on the hardware used for
testing this may be too low. Increased to 120 seconds
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
It is desired to have the peripheral writes completed to clear the
interrupt condition and de-assert the interrupt request to GIC before
EOI write. Failing which spurious interrupt will occur.
A barrier is needed to ensure peripheral register write transfers are
complete before EOI is done.
GICv2 memory mapped DEVICE nGnR(n)E writes are ordered from core point
of view. However these writes may pass over different interconnects,
bridges, buffers leaving some rare chances for the actual write to
complete out of order.
GICv3 ICC EOI system register writes have no ordering against nGnR(n)E
memory writes as they are over different interfaces.
Hence a dsb can ensure from core no writes are issued before the
previous writes are *complete*.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Many issues:
- heapmem[] is of type uint64_t meaning that it contains HEAP_SZ * 16
bytes but the heap is initialized with only 1/16 of that, making
this test's memory footprint way too large.
- The test to ensure the heap is empty uses an allocation size of
(heap_end - heap_start - 8) which is wrong as heap_end and heap_start
are uint64_t pointer types and therefore their difference will be 8x
smaller than intended. Furthermore, the 8 here is unnessary as the
chunk header size is already included in the location of heap_start.
- The heap start address misalignment bare no purpose as the misaligned
start of the free heap is already controlled by the variable prefix
allocation size.
- Alignment and sizes should rather be expressed in terms of size_t
rather than uintptr_t.
Fix those issues, and add a few more test angles:
- Make the prefix allocation itterate across the entire alignment range
to exercize all possible misalignments.
- Vary the aligned allocation size to better exercize the pre-alignment
allocation and suffix handling.
- Double the aligned allocation to add more variability in the heap
structure.
- Test the testing of emptiness by making sure that no more allocations
are possible when we think we allocated it all.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
If we pass --west-flash with no additional argument that was getting
treated the same as if it wasn't passed at all.
Change the check to be based on 'None' to handle the bare --west-flash
case properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This option should be selected by default, as right now LORA=y selects
REQUIRES_FULL_LIBC.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Right now we depend on NEWLIB_LIBC to build Zephyr with LORA=y. This
seems to be the only Kconfig option like that. Convert it to select
REQUIRES_FULL_LIBC instead, which will select NEWLIB_LIBC by default and
allow to use external libc as well.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fixes the frdm_k64f and twr_ke18f boards to enable the kinetis
temperature sensor only if the sensor and adc drivers are both enabled.
This fixes a logging error seen at runtime in
samples/bluetooth/peripheral_hr.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Currently printk isn't synchronized except at the byte output level,
leading to interleaving of messages on SMP systems that try to log
simultaneously. This is actually fairly amusing, and actually helpful
occasionally to validate inter-CPU contention down to the "few cycles"
level.
Still, when you're printing data you need to read, you need to be able
to read it. Put a spinlock around each buffered line. This has to
happen in a few places, as there are three different code paths taken
for !USERSPACE, syscall, and user mode.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Sleeping for a full second at startup is needless. The currently
enabled subsystems on platforms that run this test don't even have any
other threads running at startup, so we're guaranteed the other core
is in idle before we even reach main(). Just a few ms is plenty.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The width for %p on 32-bit targets should be 8 regardless of
CONFIG_PRINTK64. Adjust the test accordingly.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
When checkpatch was updated, this behavour seems to have changed.
This change re-adds the check for C99 comments to prevent them.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
nvs_gc does not verify the crc8 of close_ate before using
close_ate.offset. This means that close_ate.offset could contain an
offset that points beyond valid ate's in the sector. For example, there
might be a valid ate at offset 0x100 but close_ate.offset is 0x200.
If that is the case that value will not be moved and so it will be lost.
Solve this by refactoring the recovery loop from nvs_prev_ate into
nvs_recover_last_ate and use that function in nvs_gc if a corrupt
close_ate is found.
The crc8 of gc_ate is not checked before trying to find another ate
with the same id. If there are no valid ate with that id in the whole
fs the inner while(1)-loop will never stop since the break condition
includes a check for a correct crc8.
Solve this by skipping gc_ate's with an invalid crc8.
Fixes#26407
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
In sensors drivers, in gpio callback function :
The device structure in parameter is related to the gpio device.
Signed-off-by: laurence pasteau <laurence.pasteau@stimio.fr>
Commit id a538dcd8f8 got rid of the usage of these pointers so they are
useless now and can be removed in this drivers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert the present initialization code into initialization macros.
Since both the uart and the usart peripheral is implemented, two sets
of initialization macros are necessary.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
classname in the junit report was not being used correctly since the
beginning. We had the targetname in the classname and put all results in
1 single testsuite.
The new output add 1 single testsuite for each platform and simplifies
the classname so that tests of the same classname can be grouped in
output, producing readable reports.
The current output can be seen here:
https://testing.zephyrproject.org/daily_tests/zephyr-v2.2.0-2533-gdbbf834605/report/index.html
This should much better once we have this change in.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some checks in sys_heap_init() depend on the externally provided size
parameter. If the check fails, this would be a bug outside of the heap
code and therefore should be flagged despite the value of
CONFIG_SYS_HEAP_VALIDATE.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Parsed value is expected to be in range (0, UINT32_MAX). Use strtoul
instead of strtoll, so we better match its range. In a tested
configuration this saves 380 bytes of flash with newlib and arm32
target.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This enables the ACPI_EC1 interface which is typically accessed
through ports 0x6A0 and 0x6A4 in Bios.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Fix the advertise object not release when a high-duty cycle directed
advertiser timeout happens. If the extended advertising feature has been
enabled in the host, but not supported by the controller then the
advertising object must be released in the connection complete event
since there will not be a advertising set terminated event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Instead of whitelist, use a filter that checks if a required
"atmel,at45" compatible node is present.
Add a build-only test case to be used by CI and provide a harness
configuration so that execution of the sample can be also verified.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Plus corresponding configuration file for the spi_loopback test that
will be activated for that board by this added capability.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This sample still used the old name of the nrf9160dk_nrf9160 board,
both in documentation and sample.yaml. Because of the latter, this
sample was not picked up by sanitycheck, what resulted in compilation
errors in the spi_flash_at45 driver not caught by CI.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
For some reason, use of the DT_NUM_INST macro in this driver was not
replaced with DT_NUM_INST_STATUS_OKAY. In consequence, this driver
could not be compiled successfully. Furthermore, because this now
undefined macro had been used inside UTIL_LISTIFY, gcc was not even
able to report an error, instead the compilation just "froze".
This patch replaces UTIL_LISTIFY(DT_NUM_INST()) with more appropriate
in this context DT_INST_FOREACH_STATUS_OKAY. It also adds an apparently
missing inclusion of sys/byteorder.h.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In some cases we were not handling return code correctly and evaluating
timeouts as a pass. Report failure correctly.
Fixes#26065
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reference an updated head that removes references to reporting
infrastructure when reporting is disabled.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Rewrite console log section to encourage bug-reporters to obtain the
console output in text-format over screenshots, as well as hinting
about other debug information that can be attached.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Test is configured with CONFIG_POSIX_API=y, so there is no reason to
check for it being enabled in C. Additionally when CONFIG_POSIX_API=n a
much "bigger" posix/sys/socket.h was included instead of net/socket.h,
which should be rather opposite.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Move the --erase option to core.py from nrfjprog.py and jlink.py,
where it is currently supported.
Using the RunnerCaps option enforcement mechanism introduced earlier,
enforce that it will only be given to runners that support it.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Require all implementations to provide a do_create(), a new
ZephyrBinaryRunner abstract class method, and make create() itself
concrete.
This allows us to enforce common conventions related to individual
runner capabilities as each runner provides to the core via
RunnerCaps.
For now, just enforce that:
- common options related to capabilities are always added, so runners
can't reuse them for different ends
- common options provided for runners which don't support them emit
sensible error messages that should be easy to diagnose and support
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We can just call super() instead of super(MyClassName, self). The
original extra verbosity is likely due to old habits of mine from
Python 2 which are no longer necessary, but got copy/pasted around.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
fatfs_open and fatfs_opendir fail to free reserved memory on error
which may lead to memory exhaustion, when too many file/dir open errors
are caused, and will cause all subsequent open attempts to fail with
ENOMEM error.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
