Increase the default CAN controller driver initialization priority from
KERNEL_INIT_PRIORITY_DEVICE (50) to 80 to allow CAN controllers on SPI
busses have their bus initialized prior to initializing the CAN controller
driver.
The only in-bound dependency on CAN controller drivers - apart from
application level code - is the drivers/net/canbus.c driver, which already
defaults to an initialization level of 81.
Fixes: #55745
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move the Bosch M_CAN header file to include/zephyr/drivers/can/can_mcan.h
for use in out-of-tree drivers.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add documentation for the remaining functions, structs, and definitions in
the Bosch M_CAN header file. Fix a few mistyped Message RAM field names
along with misnamed macros and function found while adding documentation.
No functional changes.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update the asserts to match the updated Bosch M_CAN minimum/maximum CAN
timing parameters.
Fixes: #58429
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The minimum/maximum CAN timing parameters for the STM32 FDCAN driver uses
the wrong values for the minimum, nominal phase segment values.
Using the static initializers fixes these and aligns them to the Bosch
M_CAN manual. The STM32G4 reference manual contains contradicting limits
for these register values.
Fixes: #58429
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The minimum/maximum CAN timing parameters for the STM32H7 FDCAN driver uses
the wrong values for the minimum, nominal phase segment values.
Using the static initializers fixes these and aligns them to the Bosch
M_CAN manual. The STM32H7 reference manual contains contradicting limits
for these register values.
Fixes: #58429
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The minimum/maximum CAN timing parameters for the Atmel SAM0 CAN driver
uses the wrong values for the minimum, nominal phase segment values. The
same goes for the maximum, nominal SJW value.
Using the static initializers fixes these and aligns them to the Bosch
M_CAN manual. The Atmel SAM C20/C21 family data sheet contains
contradicting limits for these register values.
Fixes: #58429
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The minimum/maximum CAN timing parameters for the Atmel SAM CAN driver uses
the wrong values for the minimum, nominal phase segment values. The same
goes for the maximum, nominal SJW value.
Using the static initializers fixes these and aligns them to both the Bosch
M_CAN manual and the Atmel SAM E70 family data sheet.
Fixes: #58429
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Some NXP SoC reference manuals contain a bug regarding the minimum values
for nominal phase segments. Valid Bosch M_CAN nominal phase segment
register values are 1 and up. Same goes for the maximum value for data
phase segment 2. Here, valid Bosch M_CAN register values are 0 to 31.
Using the static initializers fixes these.
Fixes: #58429
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
There is no need for iterating all the Bosch M_CAN filter elements in
Message RAM in order to find a free filter as the driver already keeps
track of assigned filters.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The Bosch M_CAN Message Marker, an 8-bit field copied from Tx Buffer
elements to Tx Event FIFO elements to aid software in identifying Tx frame
status, need not be split into an index and a count, as the count is
unused.
Remove this split and replace "struct can_mcan_mm" with a simple "uint8_t".
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The Message RAM layout used by the STM32 FDCAN IPs contains a fixed number
of elements, even though the software can opt to use less standard/extended
filter elements. Change the BUILD_ASSERT() statements to reflect this.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Let the Bosch M_CAN front-end drivers supply their own Message RAM
read/write/clear functions.
This is preparation for supporting per-instance Bosch M_CAN Message RAM
layouts and for accessing Bosch M_CAN IP cores over peripheral busses.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Document that the Bosch M_CAN read/write register functions are allowed to
return -ENOTSUP for unsupported registers.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Calling for can_stop() method was not emptying FIFOs
and tx_msgq.
Resetting TX FIFO to empty it.
Emptying tx_msgq with "ENETDOWN" return code.
Fixes#50546
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Driver was based on can_sam. SAMC21 has only 1 interrupt for one
can "output", so can interrupt has to executes two lines of
interrupts.
CAN is configured to use OSC48M clock via GLCK7. GLCK7 is set
by divider configured from dts.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
Add Kconfig guards for CONFIG_CAN_MAX_STD_ID_FILTER and
CONFIG_CAN_MAX_EXT_ID_FILTER as they only apply to the STM32 bxCAN driver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the STM32H7 specific Kconfig overrides for setting the maximum
number of standard and extended CAN RX filters as they are unused.
The number of available standard and extended filter elements for Bosch
M_CAN can be configured via the devicetree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move definitions of the STM32 FDCAN specific registers to the front-end
driver implementation and implement remapping of these registers to/from
the standard Bosch M_CAN registers.
Some of the STM32 FDCAN register bit fields are limited in size compared to
the Bosch M_CAN specification. This is due to hardware limitations on the
number of elements in the various sections of the Message RAM. Add build
assertions to ensure the number of elements specified do not exceed the
hardware limitations instead of using custom definitions for these fields.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move definition of the NXP LPC MCAN specific Message RAM Base Address
register (MRBA) to the front-end driver implementation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Some Bosch M_CAN IP core implementations use a fixed Message RAM
configuration, other use a fixed memory area and relative addressing,
others again have custom registers for configuring the Message RAM.
Move the responsibility for configuring the various Bosch M_CAN Message RAM
addresses to the front-end drivers. This removes some of the front-end
specific code from the backend. Provide a helper function for configuring
the most common variations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Expose the can_mcan_read_reg()/can_mcan_write_reg() along with all the
Bosch M_CAN register definitions for use in Bosch M_CAN driver front-ends.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Let the Bosch M_CAN front-end drivers supply their own register read/write
functions.
This is preparation for handling non-standard Bosch M_CAN register layouts
directly in the front-end and for accessing Bosch M_CAN IP cores over
peripheral busses.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use sys_read32()/sys_write32() instead of volatile struct for register
access. Be consistent in using unsigned constants in register
comparisons. Use locking around register read-modify-write operations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Regenerate/rewrite the Bosch M_CAN register field definitions using the
GENMASK() and BIT() macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use the FIELD_PREP() and FIELD_GET() macros instead of manual bitshifts and
masking. Be consistent in the use of register field definition macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the local "const struct can_mcan_config *" variables from "cfg" to
"config" to be consistent with Zephyr conventions.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Get rid of the can_mcan_configure_timing() helper function as it provides
no benefit to just having the implementation split in can_mcan_set_timing()
and can_mcan_set_timing_data().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move the driver initialization function to the bottom of the file to be
consistent with Zephyr conventions.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Pass a pointer to the struct device for internal driver functions instead
of passing around a pointer to the register struct.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This patch introduces support for NXP S32 CANEXCEL (CANXL) peripheral.
CAN protocol supporting:
- CAN classic
- CAN FD
Remote transmission request is not supported as this feature is not
available on NXP S32 CANXL HAL.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
The MCUX platform always uses pinctrl, there's no need to keep extra
macrology around pinctrl. Also updated driver's Kconfig options to
`select PINCTRL` (note that some already did).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Rename the nxp,kinetis-flexcan devicetree compatible to nxp,flexcan as it
is not specific to the NXP Kinetis series.
This is preparation for adding a nxp,flexcan-fd binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
