These changes turn out to have been incompatible with the way pinctrl
drivers are going to work, so we need to go back to what we had before
until we can agree on a better approach.
Squash of the following reverts:
Revert "boards: nrf: fix deprecated I2C properties"
This reverts commit 2a4ac9ac02.
Revert "samples: switch nrf overlays to sda-gpios, scl-gpios"
This reverts commit 01bb08e7d8.
Revert "boards: nrf: switch to sda-gpios, scl-gpios"
This reverts commit 17a66304c4.
Revert "i2c: nordic: switch to phandle arrays for pinmux"
This reverts commit 821c03a14a.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Move the BOARD.dts files for Nordic-based boards to use the new I2C
devicetree properties for specifying the SDA and SCL pins.
This was done with a script.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add chosen nodes for secure and non-secure RAM partitions
and update the common DTS to have a reserved-memory
node with all reserved RAM partitions
Signed-off-by: Alex Tsamakos <alex@actinius.com>
The SoC node has compatibles for the specific SoC in place, having the
same compatible at the top level is technically a conflict and the
top-level one should really just be about the board. Remove the SoC
related compatibles at the top-level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
In initialization code, pairs of gpio_pin_configure/gpio_pin_write are
replaced with calls to gpio_pin_configure that configure a given pin as
output with the proper initial state.
dts file for the board is also updated with the new GPIO flags.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
