This is in preparation for adding another SoC where qemu_xtensa
is no longer valid choice. So use qemu_xtensa/dc233c as it is
the same as the old qemu_xtensa.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update the documented value range that `uart_irq_tx_ready` returns in
order to provide more information to the callers about the number of
bytes that could be writted with `uart_fifo_fill` without fragmentation.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Added support for dynamic registration and unregistration of the
Broadcast Audio Scan Service (BASS) within the scan delegator.
This enables both scan delegator and BASS to be registered or
unregistered dynamically at runtime.
Signed-off-by: Babak Arisian <bbaa@demant.com>
By default, TFM enables hardware rollback protection, which requires a
security counter to be embedded in the image trailer. The default
behaviour of constructing this counter from the image version breaks the
TFM `boot_nv_security_counter_update` implementation once the version
number is greater than `0.0.1024`. As such, explicitly specify the
desired security counter value. As per the MCUboot docs, this does not
need to be incremented on every firmware update.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The CSIP spec states that the procedures shall only be done
on bonded devices, so a check for that was added.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Infom users about Kconfig options deprecation, and provide code snippets
on what they have to do now.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
`CONFIG_MP_NUM_CPUS` has been deprecated for more than 2
releases, it's time to remove it.
Updated all usage of `CONFIG_MP_NUM_CPUS` to
`CONFIG_MP_MAX_NUM_CPUS`
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Added new Kconfigs for defining permission level of GATT
characteristics that are part of the Bluetooth SMP service in the
MCUmgr subsys.
Removed the CONFIG_MCUMGR_TRANSPORT_BT_AUTHEN as the new Kconfig
options are mutually exclusive and need to be groupa as the Kconfig
choice option.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
trivial typo fix where single backticks should be used instead of double
for the sphinx role kconfig:option
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Fixes bad usage of single backticks in lieu of double backticks for
rendering inline literals, or simple '*' for italics.
When appropriate, a better construct than double backticks has been
selected (ex. :file:, :kconfig:option:, :c:func:, ...), or proper :ref:
have been used if the original intention was to have a link.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
According to Mbed TLS changelog this feature was set default ON
since 3.1.0 release, so the build symbol is no more available.
This commit removes it from Zephyr.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Added option to set the ASE count through the bap API, making ASE
configuration runtime available. The upper limit of ASEs are still
bound by the Kconfig options set for ASEs.
Signed-off-by: Fredrik Danebjer <frdn@demant.com>
STM32CubeProgrammer is now selected as the default runner for all STM32
official boards when 'west flash' is invoked.
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
Mention that the GNSS periodic config APIs have been removed in the
release notes for 4.0
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The legacy bridging code prevented normal IP traffic to the
bridged Ethernet interfaces. This is not intuitive and differs
how bridging setup works in Linux. This commit changes that and
creates a separate virtual interface that is doing the actual
bridging. This enables the bridged Ethernet interfaces to work
normally and provide IP connectivity.
How this works in practice:
* User needs to enable CONFIG_NET_ETHERNET_BRIDGE
* User needs to have a device with more than one Ethernet
interface
* After booting, the net-shell or program API can be used
to add interfaces to the bridge like this.
net bridge addif 1 3 2
where the 1 is the bridge interface index and
2 and 3 are the Ethernet interface indices.
* The bridging is then finally enabled / started when the
bridge interface 1 is taken up
net iface up 1
* If bridged interfaces are removed from the bridge (minimum
of two interfaces are needed there), then the bridging is
disabled automatically. The bridge interface stays up in
this case and can be taken down manually.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add default memory partitioning for the nRF53 and nRF91 series devices.
As these partitions refer to TF-M and the TF-M layouts cannot be
modified, use the partitioning scheme from TF-M.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Following addition of a `name` to hal_stm32 module, the command to fetch
blobs that are required to build BLE applications on STM32WBA socs is now
changed from `west blob fetch stm32` to `west blob fetch hal_stm32`.
Update documentation and warn users in migration guide.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Added entries in the release note & migration guide about the
changes to the `kernel thread` shell command.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Automatically handle device runtime PM for all flash API calls.
Asynchronously release the device after a small delay to minimise power
state transitions under multiple sequential API calls (e.g. NVS).
Signed-off-by: Jordan Yates <jordan@embeint.com>
The driver in tree is for u-blox M8 devices, not M10. The M10 series
devices (from Protocol Version 23.01) use a different, non backwards
compatible interface for configuring the modem behaviour.
Of the two boards tested in the original PR, the "VMU RT1170" is
explicitly listed as having a u-blox NEO-M8N modem, while I have
been unable to find any information online about the "FMURT6" board.
Leaving the naming as-is will cause problems when M10 drivers are
contributed.
Signed-off-by: Jordan Yates <jordan@embeint.com>
NXP IMX USDHC fallback card detection method changed from querying the
peripheral to simply assuming the card was present. Add a note to the
migration guide highlighting this and explaining how to restore the
previous behavior for anyone using this detection method.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
All the network related shell activities should be under
network shell so moving it to "net bridge ..." command.
Add this information to migration guide.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add conn parameter to status/flags callbacks of bt_vcp_vol_rend_cb
to differentiate between remote and local changes.
Signed-off-by: Chang An <chang.an_1@nxp.com>
Pin definitions should correctly reflect the actual drive mode of the GPIO
controller, either push-pull or open drain.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This allows getting rid of the ngpios property, which is implicit in the
part number. It also prepares for configuring pins as open-drain on
supporting chips in the next commit.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Inform users about Kconfig options deprecation and show what is the
alternative with some examples.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add a point for the updated callback API as well as the analog axis
inversion property rename.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
