Some NXP boards are not detected by twister when creating hardware map,
because manufacture name is NXP instead of NXP Semiconductors expected
by twister.
Fix it by adding NXP to manufacturers list.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add option to flash board before attach serial.
Current implementation performs the following sequence:
1. Open serial port to listen to board log output
2. Flash device
In case of ESP32 where it uses the same serial port
for both operations, flashing needs to come first.
This PR adds a twister option named --flash-before
which enables the process above, allowing tests to be
performed properly.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
When scanning ports the manufacture field is not always
filled. It must be checked before using.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
NXP boards with CMSID-DAP are not detected by twister
--generate-hardware-map, because serial device name 'mbed' is compared
with upper case 'MBED' in a list of supported manufacturers.
Fix it by making the comparison case-insensitive.
Tested using mimxrt1020_evk.
Fixes#63765
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Use the natural sort of list when generating a hardware map. The
list is sorted with a serial port as a key. When more than 10 ports
are active and some of devices use more than one port, the ports
of one device may be listed in wrong sequence, which may cause
futher problems with selecting the right port for listening to
the device.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
After generating a hardware-map a platform field is marked
as 'unknown'. If it is not changed, do not process them
when running --device-testing.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
Convert following construction:
elif self.options.device_serial or self.options.device_serial_pty:
if self.options.device_serial:
...
else
...
to the construction:
elif self.options.device_serial:
...
else self.options.device_serial_pty:
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use flash_timeout and flash_with_test options not only for
serial console but also for device_serial_pty.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use explicit flash command execution timeout at DeviceHandler
instead of the hardcoded value of 60 sec.
When a HW platform executes test cases right after the flash command,
the test case remaining timeout is affected by how much time the flash
operation consumes. Some simulation platforms need to spend significant
amount of time on each 'flash' cycle, usually adding the same delay on
each test case.
This improvement adds two new command line options and device map fields:
--device-flash-timeout - for the flash operation timeout
('flash-timeout' device map field).
--device-flash-with-test - to indicate that the platform flash
command also runs a test case, so the overall timeout should be
calculated as a sum of the flash timeout and the current test case
timeout to receive all console output from the platform
('flash-with-test' device map field).
The device map field values override command line values for the
particular platform where configured.
Default behavior is backward compatible: flash operation fixed timeout
is 60 sec. not including the test case timeout.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
When re-generating hardware map for DKs with more than 1 serial port (more
enries in the hardware map), then we keep enfo only about the last entry.
For boards like nrf5340 it works, because the last serial port is used,
but for nrf52840 with two ports, the first one is important, so after
re-generating the hardware map it does not work.
The solution is to keep all entries after re-generating the hardware map.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
On windows, some board manufacturers have name that is "Microsoft"
instead of real its name. Need add it to manufacturer list.
Product information is missing. we can assign it "unknown" and
then add missing informations by hand.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
