Copy the DMA channel information to both UART and SPI
instances of the Flexcomm as only one of them can be
active.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Enable serial interface on i.MX8ULP.
This also includes a SHA update for hal_nxp which
pulls in the following commits relevant to Zephyr:
* 3366f234ed47 build: hal_nxp: add TPM counter support
* 6544455fcf46 Compile in PXP driver if LVGL is set to use
PXP.
* 31463a848bcd devices: MIMX8UD7: add definition for
LPUART_RX_TX_IRQS
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Currently, all devices are initialized at boot time (following their
level and priority order). This patch introduces deferred
initialization: by setting the property `zephyr,deferred-init` on a
device on the devicetree, Zephyr will not initialized the device.
To initialize such devices, one has to call `device_init()`.
Deferred initialization is done by grouping all deferred devices on a
different ELF section. In this way, there's no need to consume more
memory to keep track of deferred devices. When `device_init()` is
called, Zephyr will scan the deferred devices section and call the
initialization function for the matching device. As this scanning is
done only during deferred device initialization, its cost should be
bearable.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
CSS was deprecated from the mcu-sdk. Removing driver from lpc55s36
to clear build error.
This is a temporary patch to remove the build error.
Fixes#69961
Signed-off-by: David Leach <david.leach@nxp.com>
Configure the 'soft-off' power state for manual selection only in the
DTS for Intel ADSP ACE 1.5 MTPM and ACE 2.0 LNL platforms.
Changes include:
- Setting 'min-residency-us' to 0 to indicate that the 'soft-off' state
is not intended for automatic selection by the power management
policy.
- Adding a 'status' property set to "disabled" to prevent the power
management policy from using this state during its decision process.
The 'soft-off' state remains available for manual selection by calling
`pm_state_force`. This change ensures that the state can still be used
when explicitly requested by the system or application, providing
flexibility for power management operations.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Implement a sensor for the output diagnostics of the power train
switch TLE9104.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This commit enables pinctrl on i.MX8ULP. This includes:
1) Adding `pinctrl_soc.h` header file.
2) Adding DTS node for IOMUXC1, which is one of the
IPs responsible for managing the 8ULP pads.
3) Adding .dtsi with pin definitions. For now, only
the LPUART7 pads are added to this file because this
is going to be the only consummer for now.
4) Modifying the `pinctrl_imx.c` driver to work for 8ULP.
5) Enabling the `CONFIG_HAS_MCUX_IOMUXC`, which is a
dependency of `CONFIG_PINCTRL_IMX`.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add definitions of PWM peripheral instances so it can be utilized
on nRF54H20 and nRF54L15 devices.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add binding for sitronix ST7796s, a MIPI DBI display controller
supporting up to 320x480 displays at 18 BPP
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The SparkFun Pro Micro header pins are numbered D1, D0, GND, ... from top
left whereas the SparkFun Pro Micro RP2040 and the Adafruit KB2040 boards
are using gpio 0, 1, GND, ... , so the pro_micro: connector gpio-map of
these boards should reflect that.
Graphical Datasheet for SparkFun Pro Micro RP2040:
https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf
Graphical Datasheet for SparkFun Pro Micro:
https://cdn.sparkfun.com/assets/f/d/8/0/d/ProMicro16MHzv2.pdf
Pinout of the Adafruit KB2040:
https://learn.adafruit.com/assets/106984
Please note that the KB2040 uses CircuitPython pin labels D0, D1 which does
not seemt correspond to the Arduino labels D0 and D1 used by the Pro Micro.
Signed-off-by: Daniel Irekvist <ulmanyar@gmail.com>
Add devicetree binding for NXP LCDIC. This controller is capable of
driving displays in 8080 or SPI 3/4 wire mode, and optionally swapping
endianness of display data as it sends it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add EDMA channels for LPUART RX and TX to LPFLEXCOMM 2 and 4, as these
nodes are enabled with the UART driver
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The initial version of an input driver for Cirque Pinnacle ASIC supports:
* Setting sensitivity
* Choosing between relative and absolute modes
* Relative mode
* Primary tap
* Swapping X and Y
* Absolute mode
* Setting number of idle packets
* Clipping coordinates outside of active range
* Scaling coordinates
* Inverting X and Y coordinates
Signed-off-by: Ilia Kharin <akscram@gmail.com>
For now DSI settings are hard-coded for the specific
LCD module used on the STM32H747I Discovery board
Signed-off-by: Erik Andersson <erian747@gmail.com>
To support the NT35510 display, some additional
options needs to be configurable in the STM32
DSI peripheral
Signed-off-by: Erik Andersson <erian747@gmail.com>
Add support for performing pinctrl operations. For now,
the only supported operation is applying the pinctrl default
state. Pinctrl is left optional to allow for scenarios in which
this is not required (e.g: AMP system in which another
OS configures the pinctrl).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add a property to select the push-pull GPIO output type to drive the
I2C recovery. The default is open-drain.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Enable clock control for i.MX8ULP. This consists of:
1) Adding a PCC node in the DTS
2) Adding a header file containing the definitions
of the clocks used by the peripherals to be enabled.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Enable sleep mode on LPC55S69 (corresponding to zephyr's runtime idle
mode). Add DT description and power api implementations.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
