Implemented a sample that shows configuration and basic usage of monitor
mode debugging feature.
Signed-off-by: Piotr Jasiński <piotr.jasinski@nordicsemi.no>
Debug monitor needs to be configured to a low priority in order to be
useful for debugging (to prioritize other interrupts when waiting on a
breakpoint).
Added a config that configures the interrupt this way.
Signed-off-by: Piotr Jasiński <piotr.jasinski@nordicsemi.no>
It seems that currently it's impossible to create a custom
implementation for debug monitor exception without updating the vector
table (z_arm_debug_monitor maps to fault).
My proposition is to make this symbol weak, so that it can be overriden.
Signed-off-by: Piotr Jasiński <piotr.jasinski@nordicsemi.no>
Change Summary: The TX/RX FIFO was not flush on initialization thus
causing bad transactions. Thus, we need to flush the FIFO, and
according to Synopsys DW I2C spec, we can flush TX/RX FIFO by clearing
the enable bit. This is verified with our own I2C test on the SoC with
Synopsys DW I2C IP.
Signed-off-by: Dennis Wang <dennisjw@fb.com>
CONFIG_SOC_MEC1501_TEST_CLK_OUT is removed from mec15xx SOC,
hence remove this configuration in mec15xxevb power management
sample and add board overlay with right configurations.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove the test clock out Kconfig from SoC level. Instead use
device tree PINCTRL entry with updated clock control driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for Microchip MEC15xx to the XEC clock control driver.
MEC15xx 32KHz clock support uses the same 32KHz source for both the
PLL and peripherals. MEC152x does not include the PCR clock monitor
present in MEC172x. MEC15xx and MEC172x support internal silicon
oscillator, parallel and single ended crystal inputs, and the
32KHZ_PIN input. MEC152x supports fall back to internal silicon
OSC when VTR and 32KHZ_PIN are turned off. Therefore in MEC152x the
internal silicon oscillator can only be disabled if using an external
32KHz which is always on. For MEC152x the driver will only use the
PLL source clock device tree value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Some baudrates are not supported in certain SoCs.
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Switch to using the dedicated `gpio_is_ready_dt`
function instead of the raw `device_is_ready`.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Switch to using the dedicated `gpio_is_ready_dt`
function instead of the raw `device_is_ready`.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Add initial support for gd32l23x series. gd32l23x used Cortex-M23, based
on ARMv8-M baseline, implement the System Timer.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Unit test project for bt_id_read_public_addr().
This part of subsys/bluetooth/host/id.c unit testing.
Signed-off-by: Ahmed Moheb <ahmed.moheb@nordicsemi.no>
should be able to configure the time spent waiting
for available resources when calling timer_create()
to not cause a hiccup in applications that require
faster response times than the original hard-coded 100 ms.
Signed-off-by: Nicholas Lowell <nlowell@lexmark.com>
Enable the channel14 of the ADC4 of the stm32U5x
to measure the vbat voltage with internal on channel 14
of the ADC4 on the nucleo board or disco kit.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Adds the DTS for the ADC4 on the nucleo_u575zi_q
with pin assignment
vref is the default value 3.3V
Note that b_u585i_iot02a board already has adc4 node.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The ADC4 requires particular sequencer configuration.
Clean section that are not used for the configuration.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Depending on the ADC instance, internal channels
temperature sensor or vbat differ.
That must be adapted so that each internal channels
of ADC4 are operational.
ADC4 is using CommonChannel config for the Sampling time.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enabling by default (if SPI3 used) because it affects all revisions
since "Engineering B", including the most recent one as of today
(revision 3).
Size changes when enabled:
- -Og: flash +160 bytes (+0.02%), RAM +8 bytes (+0.01%)
- -Os: flash +144 bytes (+0.02%), no change to RAM usage
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Update action-manifest to the latest commit, pick up:
a6d0c6e action: match revisions with a refs/ prefix
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a missing ":" for "Drivers: Regulators", currently causing PR
assigner failure:
```
yaml.scanner.ScannerError: while scanning a simple key
in "MAINTAINERS.yml", line 976, column 1
could not find expected ':'
in "MAINTAINERS.yml", line 977, column 3
```
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The field has never been populated and was used by shell
and MCUboot. MCUboot Zephyr code has been changed some
time ago and no longer uses the field, flash_map shell
also no longer uses it, so it can be removed now.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit changes flash_map list output to display flash_map
assigned pointer instead of device ID which was not propagated
anyway.
The commit also fixes formatting of the output.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Save FP user register and FP register file during context switch.
This change enables shared FP registers mode using CONFIG_FPU_SHARING.
Since there is no lazy stacking, the FPU registers will be saved regardless
of whether floating point calculations are performed in the threads when
CONFIG_FPU_SHARING is enabled. This require 72 additional bytes in the
stack memory.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Add entry for regulator drivers. Add myself as a maintainer as I've been
reworking the whole subsystem lately, and Daniel DeGrasse as a
collaborator as he's been active in reviews and implementations.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Refactor the regulator shell so that it exposes all regulator APIs
- vset/iset commands allow to specify a single value (equal min/max) or
a range
- Voltage/current input is now more user friendly, e.g. user can specify
units and decimals: 3.3v, 200mv, -4mv, etc.
- Reported values are also printed in a more user friendly way, e.g.
1800000 uV will be printed as 1.800 V.
- Added new command to list supported voltages
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Ranges with step 0, that is, multiple indices representing the same
value, need to report the count exclusively based on indices. This makes
it possible to later retrieve all values, e.g. in a group.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
