On Quark SE, SPI might require GPIO to be ready before hand, to emulate
CS, thus providing an option to tweak the intialization priority for SPI
DW driver.
Change-Id: Ifa373948ac8227bf6e4ed1113bcb4dc9139b6663
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Quarks SE owns a GPIO controller which is always on (so not clock-gated)
thus providing it base address, the pins it handles etc...
Change-Id: Ifceb7cb74e763a91130d615ba19756ddcbe97a23
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The original value of 128 was selected more or less randomly, and
isn't sufficiently large enough for QA needs.
Change-Id: I8a9fcc86d6b5fa7dc5ba05896c62f7dd608f9ed2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These are not (yet) used anywhere and generate unnecessary warnings.
Just remove them.
Change-Id: Ibae472c4a639466c221cdc354232780db04e963e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define configuration for Nordic chip connected to UART0.
Change-Id: Ia6007def747932e5f9fbd57f1ea8005892a2f793
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Currently, if we disable I2C_DW through 'menuconfig', I2C_DW_0* and
I2C_DW_1* options are not disabled even if they depend on I2C_DW
option. This makes the menuconfig confusing and we end up with the
wrong config set in .config file:
...
CONFIG_I2C_DW is not set
CONFIG_I2C_DW_0=y
...
CONFIG_I2C_DW_1=y
...
This patch fixes this issue by surrounding the I2C_DW_0* and I2C_DW_1*
options with 'if I2C_DW'.
Change-Id: I7e949b066425bca2533f8b84b9ea7b1915369ff0
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch introduces the 'QMSI RTC device driver' which is simply a shim
driver based on RTC driver provided by QMSI BSP.
Some config options are independent of the driver implementation used,
so use a consistent name for them. In this case RTC Interrupt number and
Priority use the same config options for both the QMSI and DesignWare
drivers.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_RTC=y
CONFIG_RTC_QMSI=y
Change-Id: I48292406e5472e5786f3b9abbeb71016a273bfec
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This enables building with the iamcu variant of the x86 compiler
and enabled using the IAMCU ABIs.
Change-Id: Idf71251898e250b8df73c065462c93c289879fe2
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change terminology and use SoC instead of platform. An SoC provides
features and default configurations available with an SoC. A board
implements the SoC and adds more features and IP block specific to the
board to extend the SoC functionality such as sensors and debugging
features.
Change-Id: I15e8d78a6d4ecd5cfb3bc25ced9ba77e5ea1122f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2016-02-05 20:25:11 -05:00
Renamed from arch/x86/platforms/quark_se/Kconfig (Browse further)
