BLE public address assignment shall be done only when
CONFIG_BT_HCI_RAW is not enabled.
Signed-off-by: Alessandro Manganaro <alessandro.manganaro@st.com>
The controller behind the EFR32 driver is a local link layer
implementation, so it makes sense to select HAS_BT_CTLR.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Change running baudrate from `115200` from `3000000`.
Implement the function `bt_h4_vnd_setup` to update the HCI bandrate.
Add Kconfig `BT_H4_NXP_CTLR_WAIT_TIME_AFTER_BAUDRATE_UPDATE` to set
the waiting time after the controller bandrate HCI vendor specific
command sent. It is used to ensure the controller is ready to update
HCI bandrate.
Select `BT_HCI_SETUP` if `BT_H4_NXP_CTLR` is enabled.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
As BT now uses PSA crypto API instead of TinyCrypt, entropy generator
is now needed for a proper bluetooth operation.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
As long as MBEDTLS_ENTROPY_C is enabled, Mbed TLS needs to
poll some entropy source to gather data that will then be
processed by CTR/HMAC-DRBG modules. This means that in most
of the cases, once MBEDTLS_ENTROPY_C is enabled then also
MBEDTLS_ENTROPY_POLL_ZEPHYR needs to be enabled. This was
done manually until now, as the long list of samples/tests
demonstrate.
This commit solves this dependency by defaulting
MBEDTLS_ENTROPY_POLL_ZEPHYR to on as soon as
MBEDTLS_ENTROPY_C is set. As a consequence, all manual
enablement of MBEDTLS_ENTROPY_POLL_ZEPHYR in samples/tests
are removed.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
-Update formatting and contents of index.rst for cy8ckit_062s4
-Update formatting and contents of index.rst for cy8ckit_064s0s2_4343w
-Update formatting and contents of index.rst for cy8cproto_062_4343w
-Update formatting and contents of index.rst for cy8cproto_063_ble
-Update formatting and contents of index.rst for xmc45_relax_kit
-Update formatting and contents of index.rst for xmc47_relax_kit
-Change all instances of "PSoC" to "PSOC" for infineon platforms
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
Zephyr 3.7.0 has been released and it is time to remove the migration
code added in 9cf07bbdb5 (bluetooth:
Rename rpmsg HCI driver and sample to ipc).
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Add dedicated Kconfig symbols for the two SPI backend variants. This
allows enabling the symbols by default from devicetree, and cleans up
the cmake logic.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Rename the Silabs HCI driver to hci_silabs_efr32.c to better indicate what
hardware it supports. Also rename the associated devicetree binding and
Kconfig options to be consistent with the new driver name.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Current code does no longer support
the non monolithic feature.
Hence, removing unnecessary code.
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
Add updates to support MCXW71
Add support if RX data are received in ISR context
Add support to set BT address using Vendor command
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
This commit applies several changes in the way "heap_runtime"
feature is used. It can't be split due to bisectability issues.
Whenever the feature is enabled, a new heap is created and
custom malloc/calloc/free functions are added into the build
system. Those functions are currently used for internal Wi-Fi and BLE
drivers only.
Such changes are described below:
1) Rename heap.c to esp_heap_runtime.c for better readability.
2) Rename RUNTIME_HEAP to HEAP_RUNTIME to make it similar to what is
available in Zephyr.
3) Add runtime heap to BT as such as Wi-Fi.
Fixes#79490Fixes#79470
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Added setup of PUBLIC ADDR
NOTE: By default, the CYW208xx controller sets some
hard-coded static address.
To avoid address duplication, let's always override
the default address by using the HCI command
BT_HCI_VND_OP_SET_LOCAL_DEV_ADDR. So
1. when cyw208xx_setup gets BT_ADDR_ANY from the host,
it will overwrite the default address, and the host
will switch to using a random address (set in the hci_init
function).
2. If user set the static address (by using bt_id_create)
before bt_enable, cyw208xx_setup will set user defined
static address.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Now that there is an actual Kconfig symbol generated for blobs presence,
take advantage of that and declare appropriate dependencies to it. Also add
helpful CMake output if the blobs are missing by taking advantage of the
zephyr_blobs_verify() CMake function.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Most of BT_FOO symbols that are designed to select the hci driver
implementation which will drive the comunication with controller are
selected based on device tree compatible and should not be made available
as an configurable option to the user.
To do this, remove the prompt on these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
- Slightly improve the name of this kconfig adding the suffix
_POLL in order to highlight that this adds a callback
function used to poll data.
- Description was also updated to point out that this symbols
might not only use the (secure) entropy driver, but also
generic number generators, some of which are not really
secure.
- The symbol was move from Kconfig to Kconfig.tls-generic because
this is where MBEDTLS_ENTROPY_C is located and since
MBEDTLS_ENTROPY_HARDWARE_ALT depends on the former (it only
makes sense if the entropy module is also enabled), we add
also the "depends on".
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
ENABLED suffix does not really makes much sense for a kconfig
so it should be removed. Also other MBEDTLS symbols were recently
updated accordingly.
Moreover having it named exactly the same way as in Mbed TLS
symplifies the understanding of what this kconfig is doing.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
The driver can run in either native_posix or native_sim.
Let's make sure to set the dependencies acordingly.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove the logic from the board level about overriding the
flash load size and instead just select to use the DT code
partition if app is not expected to be able to occupy the
whole flash space because of the firmware image being
loaded separately.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Enabling BT_HCI_SETUP for STM32WB55 to have a
correct and proper initialization procedure to fix
#75318 issue
Signed-off-by: Alessandro Manganaro <alessandro.manganaro@st.com>
Add Kconfig.nxp to support NXP Bluetooth Chipset.
Current only NXP IW612 Chipset (BT_NXP_NW612) has
been supported.
Add modules/hal_nxp/bt_controller/CMakeLists.txt to
determine whether any firmware is selected, and
check whether the firmware exists.
If the firmware exists, copy the firmware to the
temporary folder ${ZEPHYR_BINARY_DIR}/include/
generated/bt_nxp_ctlr_fw.h. OR, raise a fatal error.
In file hci_nxp_setup.c, includes the temporary file
bt_nxp_ctlr_fw.h.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Implement UART firmware download driver for NXP
BT module.
Only support Murata 2EL M.2 module on RT1170EVKB.
And only one instance can be supported now.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Convert the slz_hci.c HCI driver to use the new HCI driver API. This also
fixes the HCI bus type to correctly indicate VIRTUAL instead of UART.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Convert the hci_nxp.c HCI driver to use the new HCI driver API. Also move
the driver binding under dts/bindings/bluetooth, like all other HCI driver
bindings.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Convert the hci_stm32wba.c driver to the new HCI API. Unlike in most cases,
the devicetree node is already enabled on the SoC level (rather than board
level). This is in order to mirror how the Kconfig option was originally
enabled, i.e. on the SoC level.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
The drivers should be independent after the move to the new HCI driver
API. Having them as a choice also has unexpected consequences with some
drivers being unexpectedly enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Convert the H4 driver to the new HCI driver API. This includes updating
also any boards that use the driver, i.e. adding the appropriate
devicetree node and chosen property to them.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Some vendor specific setup was done inside
the open() HCI function, those should be
inside setup() function instead.
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
The driver isn't currently buildable due to "west blobs" support never
having been added for hal_telink. Furthermore, even if the blob
dependency is manually made available it turns out the code has
bitrotten to the point where it doesn't build anymore. This situation
has continued for several years without anyone taking action, so I think
it's safe to assume this is unmaintained and should be removed.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
This commit add the SPI-based HCI support for the Ambiq Apollo3 Blue
SOC (e.g. Apollo3 Blue Plus, Apollo3 Blue) support.
Also correct the dependency of necessary peripheral.
Signed-off-by: Aaron Ye <aye@ambiq.com>
Add HCI driver generic to NXP platforms.
Update west.yml to have ble support for rw61x
Signed-off-by: Axel Le Bourhis <axel.lebourhis@nxp.com>
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
This adds HCI driver which enables communication with CMAC core on
Renesas SmartBond DA1469x series. The CMAC core is running an Apache
NimBLE controller binary and uses shared memory for communcation via
mailboxes.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
This commits create the dts binding for Ambiq BT HCI instance.
And create the SPI based common HCI driver for Ambiq Apollox
Blue SoC and the extended soc driver for HCI.
Signed-off-by: Aaron Ye <aye@ambiq.com>
Remove BT_SPI_BLUENRG Kconfig parameter as it is redundant according to
the new changes introduced by ST SPI protocol V1 and V2.
Remove "config BT_SPI_BLUENRG" from the boards that were using it.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
