This transforms the existing driver for the Microchip MCP9808
to be used as a generic driver to be used with all
JEDEC JC 42.4 compliant temperature sensor chips.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Added new flag CONFIG_WIFI_NM_HOSTAPD_AP for hostapd support. Once this
flag is enabled, softAP will be setup by hostapd. Both wpa_supplicant
and hostapd uses same task and eloop.
Included necessary hostapd files when compiling wifi samples if
CONFIG_WIFI_NM_HOSTAPD_AP is enabled. Added hostapd support for all
softAP command of L2 wifi shell commands.
Signed-off-by: Hui Bai <hui.bai@nxp.com>
IPPROTO_IPV6 option was set on TCP socket (besides doing it already in
tcp.c) instead of UDP. Fix that.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Describe the samples using code-sample directive in preparation for
upcoming changes to the Zephyr documentation that will be leveraging
the provided description and metadata.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Describe the samples using code-sample directive in preparation for
upcoming changes to the Zephyr documentation that will be leveraging
the provided description and metadata.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Describe the samples using code-sample directive in preparation for
upcoming changes to the Zephyr documentation that will be leveraging
the provided description and metadata.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Drop support for Google Kukui EC board which was used for
early Zephyr experiments but doesn't really exist anymore.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Remove `SPI_NOR_IDLE_IN_DPD` to simplify the possible transition states
in the `spi_nor` driver. This option was originally added 5 years ago
when device runtime PM was in a much less mature state.
I do not believe having a separate power management implementation for
this one in-tree driver is in the interests of the project.
The behaviour of `SPI_NOR_IDLE_IN_DPD` leads to extremly suboptimal
behaviour in use cases where multiple small reads are performed
sequentially, see #69588.
Removal of this option does not break the behaviour of any existing
applications, only increases current consumption in idle by ~10uA until
device runtime PM is enabled.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The driver in tree is for u-blox M8 devices, not M10. The M10 series
devices (from Protocol Version 23.01) use a different, non backwards
compatible interface for configuring the modem behaviour.
Of the two boards tested in the original PR, the "VMU RT1170" is
explicitly listed as having a u-blox NEO-M8N modem, while I have
been unable to find any information online about the "FMURT6" board.
Leaving the naming as-is will cause problems when M10 drivers are
contributed.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The sample illustates how to achieve bidirectional asynchronous audio.
Implicit feedback is the only way to achieve asynchronous USB headset
on devices that have only one isochronous IN and one isochronous OUT
endpoint.
The sample implements stereo playback and mono recording. While it would
be possible to have stereo recording, the commonly available headsets
are mono only. The number of channels can differ between audio sink and
source because the only requirement is that the two run on same clock.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Low throughput links (e.g. IEEE 802.15.4) require additional stack and
buffering resources. Therefore some stack and buffer pool sizes were
increased to cater for over-the-air scenarios.
Fixes: #77287
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
ENABLED suffix does not really makes much sense for a kconfig
so it should be removed. Also other MBEDTLS symbols were recently
updated accordingly.
Moreover having it named exactly the same way as in Mbed TLS
symplifies the understanding of what this kconfig is doing.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Added the battery level status char to bas service
as per bas_1.1 spec. Added BSIM test for BAS service
to test the NTF/INDs of BAS characteristics.
Signed-off-by: Nithin Ramesh Myliattil <niym@demant.com>
Add conn parameter to status/flags callbacks of bt_vcp_vol_rend_cb
to differentiate between remote and local changes.
Signed-off-by: Chang An <chang.an_1@nxp.com>
Add missing braces to comply with MISRA C:2012 Rule 15.6 and
also following Zephyr's style guideline.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Add basic WPA2 EAP-TLS support.
Also, add test infrasturcture esp. the certification handling,
non-certificate credentials are take as runtime input and certificated
are build time input for testing.
A real application can set certificates at runtime too.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Exclude the nucleo_h755i_q m4 core from the flash_shell samples,
as the m4 core in stm32h7 parts does not have flash support in Zephyr.
Signed-off-by: Mike Banducci <michael.banducci@sandc.com>
Nrf54h20dk and nrf54l15 have UART Flow Control enabled
by default on all cores.
It's a source of problem when mbox sample is run in Twister.
Twister opens serial port only on host core,
thus nobody confirms reception of logs from remote core.
As a result, remote core stucks on printing boot banner.
Twister fails sample due to the timeout while waiting for messages
from remote to host.
Disable Flow Control on remote core when mbox sample is executed
on nrf54h20 or nrf54l15.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Added mimxrt1040_evk to inregration platforms, so that fxls8974 is tested,
and added config for mimxrt1040_evk to sensor_shell
Signed-off-by: Krystof Sadlik <krystof.sadlik@nxp.com>
DHCPv4 server will probe the offered IP address (send ICMP echo request)
and wait for 1s (default) before offering the address. STA sends out DHCP
discover, but gets no response. Windows automatically assigns the network
card an IP address of 169.254.xx.xx.
So set timeout for ICMP probe sent by the server to 100ms.
Signed-off-by: Gang Li <gang.li_1@nxp.com>
Clean up documentation pages for the new perf tool
as they contained several typos, grammar errors, and
duplicated content between main doc page and sample
page
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Notify only if the device configuration has changed. Pass only the
configuration value as the message status, the actual device speed can
be obtained with usbd_bus_speed().
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Convert users of net_buf_put() and net_buf_get() functions to use
non-wrapped putters and getters k_fifo_put() and k_fifo_get().
Special handling of net_bufs in k_fifos is no longer needed after commit
3d306c181f, since these actions are now
atomic regardless of any net_buf fragments.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Sample was modified to enable pull-down when using EXT1 pins for
wake-up on deep sleep sample in order to simplify testing in case
user doesn't notice external pull-down will be needed otherwise.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
In order to mitigate side channel attacks, even if the PWE is found the WPA
supplicant goes through full iterations, but in some low-resource systems
this can be intensive, so, add an option to exit early.
Note that this is highly insecure and shouldn't be used in production
Signed-off-by: Gang Li <gang.li_1@nxp.com>
To demonstrate the usage of the UATT MTU API to determine if a payload
with its associated length can be sent over a GATT notification.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
The OK response should be processed before entering CMUX mode.
Use UART ISR mode by default.
Fix warnings and errors produced by the sample.
Signed-off-by: Ryan Erickson <ryan.erickson@ezurio.com>
Move samples config files from 'boards' to 'socs' in order to
remove multiple files with the same configuration and render
available samples for new boards. Only changed sample files
which are not board or hardware specific.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Added a websocket connection sending network statistics to a client, to
demonstrate how this can be used to push data to the client as an
alternative to GET requests triggered by a Javascript timer.
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
Accept JSON payload including LED number and state, to demonstrate JSON
parsing and allow control of multiple LEDs if the board supports this.
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
