Conform to Bluetooth Specification, if the LE_Scan_Enable
parameter is set to 0x01 and scanning is already enabled,
any change to the Filter_Duplicates setting shall take
effect. Disabling scanning when it is disabled has no
effect.
Fixes#31019.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix BIG Sync Terminate Command to generate Sync Established
event if Sync initiation is in progress.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation of HCI_Set_Connecitonless_CTE_TX_Enable
command to HCI. Add scratch implementation of command handling
functions to controller.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Correct names of kconfig entries to mach to style of other entries.
Style correction in hci.c. Use the same approach of checking if
Kconfig entry is enabled.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Implements handling of the BIG sync commands in the ULL.
LLL support and handling of ACAD (biginfo) remaining.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Clean up included header files, remove including
zephyr/types.h and other deprecated or redundant
header files.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation of HCI_LE_Set_Connectionless_CTE_-
Transmit_Parameters command in HCI.
Add implementation of command handling in controller.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
'ext_hdr' member only covers extended header part of 'ext_hdr_adv_data'
and with addition of 'data' member to 'pdu_adv_ext_hdr' those can be
used to quickly access both extended header flags and data directly
from 'pdu_adv' without need for extra local variables and casts.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
pdu_adv_hdr name is quite confusing since it suggests some generic
header for advertising PDUs while this in fact is extended header
which is a part of common extended advertising payload and only applies
to extended advertising PDUs.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
The 'adi' part of that member name does not make sense since ADI is
already part of extended header, so we only have 'extended header' and
'advertising data'.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
If handle mapping is enabled, we need to use proper advertising set
handle in HCI event.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Removed the node_rx argument for the BIG create/terminate
functions. The event should not be sent right after the
command, but needs to wait for transmissions of
empty BIS packets or BIG terminate indications.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Implements the BIG terminate command that terminates a
BIG and returns the appropriate events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Implements handling of the BIG create command in the upper link layer.
Does not yet handle sending any BIS events.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Put infrastructure for the following HCI commands/events in place:
* LE Read ISO Link Quality command
* LE Read ISO TX Sync command
* LE Set Host Feature Command
Signed-off-by: Asger Munk Nielsen <asmk@oticon.com>
Fix field names of bt_hci_cp_le_setup_iso_path in le_setup_iso_path to
make CIS central/periphal compile and adjust parameter names for
ll_setup_iso_path accordingly.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Implement HCI commands to read information about supported codecs and
controller delay.
* Read Local Supported Codecs command (v1 and v2)
* Read Local Supported Codec Capabilities command
* Read Local Supported Controller Delay command
The following functions are implemented as "weak" symbols and should
be overridden to fill in vendor-specific information into the above
commands.
* hci_vendor_read_std_codecs
* hci_vendor_read_vs_codecs
* hci_vendor_read_codec_capabilities
* hci_vendor_read_ctlr_delay
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Add implementation of HCI_LE_Set_Connection_CTE_Transmit_Parameters
for Bluetooth 5.1 Direction Finding.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add partial implementation for handling Bluetooth 5.1 Direction
Finding HCI command HCI_LE_Read_Antenna_Information to controller
Upper Link layer.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Fix node rx buffer leak if extended advertising and/or
periodic sync reports are masked out by the host.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added code comments to explain the reasons to drop
incomplete advertising and sync report.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix Extended Advertising Report generation that skipped
population of AD data when there was no extended header.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Put infrastructure for the following HCI commands/events in place:
* LE Setup ISO Data Path command
* LE Remove ISO Data Path command
* Configure Data Path command
* LE Set CIG Parameters Test command
* LE ISO Read Test Counters command
* LE ISO Receive Test command
* LE ISO Test End command
* LE ISO Transmit Test command
Signed-off-by: Asger Munk Nielsen <asmk@oticon.com>
Fix Extended Advertising Data population when there is no
Extended Header to be filled.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Instead of guarding the NODE_RX_TYPE_USER cases with
CONFIG_BT_CTLR_USER_EXT we guard them with
CONFIG_BT_CTLR_USER_EVT_RANGE > 0 as that is the actual value that
enables/disables the NODE_RX_TYPE_USER values.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Instead of having explicit values for each entry in the enum that
has to be updated for each new entry (thus requiring manual work
which can also be error-prone), the enum will now be
self-incrementing, to make it easier and safer to add new
entries.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Put infrastructure for the following HCI commands/events in place:
* LE Set CIG Parameters command
* LE Remove CIG command
* LE Create CIS command
* LE Accept CIS Request command
* LE Reject CIS Request command
* LE CIS Established event
* LE CIS Request event
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Fix the ll_scan_enable interface signature, place duration
before period parameter to reflect the order as in the HCI
LE Set Extended Scan Enable command.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactoring of conditional compilation related to extended
scanning with duration and period.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove generation of Periodic Sync Lost HCI event generation
that is not needed as per BT Spec. v5.2 Vol.4 Part E.
Section 7.8.69.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to perform Periodic Sync Terminate,
generation of Sync Lost on terminate and on remote device
termination of Periodic Advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fill the correct local clock accurracy in the Sync Info
structure in the Periodic Advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
