Terminate connection when Connection Update with instant in the past
Fix type re. win_offset calc in conn update ind pdu decoder
Remove feature bit on unsupported in peer
Signed-off-by: Erik Brockhoff <erbr@oticon.com>
Upon collision either the error code for different procedure
collision or same procedure collision must be transmitted,
which is fixed in this PR. Previously always the error code
for same procedure collision was sent
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
Add Extended Advertising Type validation when associated
Periodic Advertising is enable, and Extended Advertising
set is re-configured to other advertising types.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
There is an error. CTE request control procedure can be run in single
shot or periodic mode. In case of run in single show, it is not
disabled after completion.
The code responsible for the disable was deleted by commit:
ac7d0506f88508e7440288c1ec4319a9f7d0ad44.
The cte_req.is_enabled should be set to zero if the CTE request
completes and cte_req.req_interval is zero.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
There was missing code responsible for handling of unexpected response
for CTE request. The commit adds code that will terminate connection
in case a peer device reposnes with unexpected control PDU that is not
a remote procedure reques.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The CTE request procedure should be enabled only if a peer supports
CTE response feature. That information can be obtained by feature
exchange procedure. If there were no feature exchange then CTE
request feature may be disabled if a peer responses with LL_UNKNOWN_RSP
for a CTE request.
The implementation of ll_df_set_conn_cte_req_enable was checking if
CTE response feature is supported only when there was feature exchange.
There was missing possibility to stop CTE request if a peer responded
with LL_UNKNOWN_RSP for an earlier CTE request.
The commit changes the implementation of ll_df_set_conn_cte_req_enable.
The CTE response feature check is moved to ull_cp_cte_req function,
because it belongs more to control procedure than to function that
handles Host request to start the procedure.
Second change is related with use of conn->llcp.fex.features_used.
It stores information about features supported by peer. It does
not depend on execution of the feature exchange control procedure.
By the way, there were removed else statement in ll_df_set_conn_cte_-
req_enable because it was not needed.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
There was missing handling of LL_UNKNOWN_RSP in CTE request control
procedure.In case there is a pending CTE request and peer responses
with LL_UNKNOWN_RSP then Host should be notified with HCI_LE_CTE_-
Request_Failed event. The pending CTE request procedure should be
completed.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Fix handling of AD Data set with operation type of
unchanged data with respect to invalid parameter and
state of Periodic Advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix nRF51x series advertising channel PDU S1 byte
configuration regression, that causes corrupted advertising
PDUs being reported to Host, by adding the missing bits_s1
local variable initialization.
Regression introduced in commit 1dcbe73cc8 ("Bluetooth:
controller: radio: add setting of S1 byte in radio packet").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Current implementation of ll_sync_create_cancel does not allow to stop
synchronization after ull_sync_setup is called. When that is done,
sync->timeout_reload is not zero and the ll_sync_create_cancel will
return BT_HCI_ERR_CMD_DISALLOWED. That means the Controller is able to
cancel periodic advertising synchronization only in period between
call to ll_sync_create and reception of AUX_ADV_IND that has SyncInfo
field.
The Controller should be able to cancell synchronization until first
AUX_SYNC_IND PDU is received and host notified about synchronization
established.
Complete information about synchronization status is provdied by two
ll_sync_set members: node_rx_sync_established and timeout_reload.
These two members of the structure were used in ll_sync_create_cancel
function to do a proper cancel and cleanup.
The node_rx_sync_established member was not cleared when sync was
established or expired. That was required to get a proper information
about synchronization state.
Besides that, to avoid race condition between ll_sync_create_cancel
and ull_sync_established_report, the latter function was extended
to check if cancel operation or sync lost has happened.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Remove experimental label from Advertising Extensions and
Periodic Advertising features in the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This PR sets the refactored LLCP as the default instead of legacy
so that more people will use this, giving us more feedback
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
Direction finding functionality does antenna switching during CTE
reception in AoA mode and CTE transmission in AoD mode. Antennas are
switched according to user provided antenna switch pattern. If a CTE
length is enough to exhaust all antenna ids in a switch pattern then
radio should loopback to reference antenna and continue from switching
from that. Current implementation loops back to antenna that is just
after reference antenna in the switch pattern.
The commit fixes that by insertion of the reference antenna
at the end of switch pattern. Radio will operate as it was before,
it will restart switching from the same index in a switch pattern.
At the same time reference antenna will be inserted into the loop
if switching pattern is exhausted. That also means, the maximum
number of antenna ids in a switch pattern has to be decreased by
one.
The commit also fixes lower bound in the BT_CTLR_DF_MAX_ANT_SW_PATTERN-
_LEN that should be equal two. It was set to three, because in the
past the antenna at index zero was used for reception of a PDU.
Now this antenna ID is provided by device tree configuration.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The SYNC_STAT_READY_OR_CONT_SCAN state into two: SYNC_STAT_READY
and SYNC_STAT_CONT_SCAN. The connected state was used for two
cases:
- synchronization with periodic advertising is already established,
- CTE type is wrong but periodic advertising list is used to filter
synchronized devices.
In the past states were connected because there was only one difference
between them. In case of sync already established, Controller generated
sync report notification to host.The sync was not terminated when
Controller was about to continue search for other periodic advertiser.
The state was split because now Controller terminates sync ticker and
continues search for other periodic advertised. The split improves
readability and makes code easier to understand.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
In case of use of filtering based on: periodic advertising list and
CTE type, the synchronization can hang. That is possible if a periodic
advertiser uses wrong CTE type. In such situation the sync is not
released in ull_sync_done call. What more the sync->timeout_reload
is not cleared and Host is not able to cancel the synchronization.
The periodic advertising is in a semi-sync-established state.
There are no reports send to Host. Host can't use the sync set to
synchronize with other device. It is only able to terminate the
sync (call to ll_sync_terminate).
To fix the issue following changes should be applied:
- isr_rx_adv_sync_estab should call isr_rx_done_cleanup
with sync_term parameter in case the sync_ok isn't SYNC_STAT_ALLOWED.
In any case the CTE type is wrong, no matter is the periodic
advertising list filtering is enabled or not.
- ull_sync_established_report should set sync->is_term to true
in case the CTE type is not allowed. That change is required for devices
that do not support Direction Finding Extension. For those devices CTE
type based filtering is done in ULL by ull_sync_established_report
function. The sync->is_term should be set unconditionally, hence is
moved up in the function.
With these two changes done, ull_sync_done function will execute
sync_ticker_release in case the CTE has wrong type. ULL, depending on
notifications prepared by ull_sync_established_report, will follow up
on sync termination if required.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The periodic CTE_REQ disable command, requested by Host, may be locked
until connection is dropped due to missing CTE_RSP from peer device.
That is caused by implementation of CTE_REQ disable and CTE_REQ
control procedure handling.
The procedure is marked as active when CTE request was send to peer
device. It is marked as inactive after completion of the procedure.
That caused locking of CTE disable on a semaphore.
The BT 5.3 Core Spec, Vol 4, Part E, section 7.8.85 says the HCI_LE_-
Connection_CTE_Request_Enable should be considered active on a conne-
ction from when Host successfully issues the command with Enable=0x1
until a command is issued with Enable=0x0 or single LLCP CTE request
has finished (CTE_Request_Interval=0x0). Also there is a clarification
from BT SIG that the command with Enable=0x0 does not affect any
initiated LLCP CTE request. That means Controller is allowed to finish
already started procedure and it is not allowed to start new LLCP CTE
request procedure after completion of the command with Enable=0x0.
Taking that into account, there is no need to synchronize ULL and LLL
in regard of disable the LLCP CTE request while the procedure is
pending. Controller is free to complete the procedure or terminate it.
The change removes all code related with cte_req.is_active, disable
callback and waiting of ULL for LLL to finish the LLCP CTE request.
The ULL will complete the HCI_LE_Connection_Request_Enable with
Enable=0x0 immediately. In case the procedure is disabled in before
the response arrives, then further processing of the response is
dropped and the procedure context released.
The context is not released by the code responsible for disable
handling, to have single place where it is done.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
There is an error in the condition that checks if new CTE_REQ should
be started after end of connection event. The condition verifies if
counter req_expire is set to zero. Then new CTE_REQ is started
irrespectively to CTE_REQ being disabled.
req_interval is used to store information if the CTE_REQ is:
- periodic, then value doesn't equal zero,
- single shot or disabled, then value equals zero.
The condition should verify if the req_interval is not zero and
req_expire is not zero. The second part of the if condition is
required to avoid starting next CTE_REQ until last one has been
completed.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Some of control procedures has set ctx->rx_opcode in rp_comm_tx
function to values that state there is an expected PDU.
This is not always true. In case of procedures that do not expect
any response from remote device, the ctx->rx_opcode should be set
to PDU_DATA_LLCTRL_TYPE_UNUSED.
In the worst cases scenario, when the same control procedure
is executed locally and remotely, correct response PDU may
cause an assertion in ull_cp_rx. It could happen because
of wrong ctx->rx_opcode value. A packet with opcode that is
set in remote and local control procedure context rx_opcode
will be treated as expected value for both. That is a situation
that cannot happen.
The commit changes the assignments of rx_opcode to fix the problem.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
This commit fixes the build errors for the testcases in
the tests/bluetooth/init folder
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
The tests/bluetooth/ctrl_user_ext test fails due to
compilation errors, which are fixed with this PR
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
In order to bring consistency in-tree, migrate all subsystems code to
the new prefix <zephyr/...>. Note that the conversion has been scripted,
refer to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Strictly restrict AD Data length to BT_CTLR_ADV_DATA_LEN_MAX
when there can be free bytes in Advertising PDU with common
extended header format of less that the maximum 64 bytes.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In a function pu_prepare_instant there is a condition that
checks if there is actual change of a PHY. That condition
was based on ctx->data.pu.tx and ctx->data.pu.rx.
These members store PHY that is or will be used, hence
the condition is wrong. Even there is no actual change in
the PHY, values could be not equal to zero. In such case
the instant value would be set to wrong value.
What more the condition be an 'or' not an 'and' because
one of the values must be different than zero to have the
PHY change and instant different than zero.
After update of the condition, the function call places
must be changed. The ctx->data.pu.c_to_p_phy and
ctx->data.pu.p_to_c_phy are set in pu_prepare_update_ind
function, hence pu_prepare_instant should be called after
that.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
- ISO TX data path for HCI and support for vendor path
- ISO-AL segmentation of framed PDUs
- Insertion of segment headers
- Reconstruction and storing of CIG reference point in ULL
- Calculation and insertion of of Time-Offset
- Exit error spooling in ISO-AL on detecting start
- ISO-AL TX unframed fragmentation
Signed-off-by: Nirosharn Amarasinghe <niag@demant.com>
Signed-off-by: Morten Priess <mtpr@oticon.com>
Add implementation to generate node rx for missing ISO PDUs
and set the status as invalid. This is required for ISOAL to
correctly track the sequence numbers for every SDU interval.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Kconfig to limit the Primary Advertising Interval and
Periodic Advertising Interval maximum supported values in
the Controller implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
None of the common DF configs should depend on using BT_LL_SW_SPLIT.
Added dependencies to it where this was the case.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
These configurations are tighlty coupled to the implementation,
so these should be hidden when not using BT_LL_SW_SPLIT.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Some controllers may support only TXing or RXing CTE.
As all DF features are guarded by BT_CTLR_DF, we need to ensure
that it is possible to select those when only TX or RX is available.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
In case a connection is encrypted received PDU is decrypted by CCM.
CCM does not encrypt/decrypt S1 byte that stores CTEInfo.
In case of reception of a PDU by encrypted connection there is missing
CTEInfo in a memory where CCM stores decrypted PDU.
The CTEInfo data must be copied from scratch packet.
The commit adds code responsible for copying of the CTEInfo into
target PDU memory.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Terminate connection with a MIC failure if an unexpected control PDU
is received during the Encryption Start procedure.
Add a greedy option to pdu_is_expected() to make sure the procedure
processes all unexpected control PDU in all cases.
Add unit test inspired by Bluetooth Qualification test
LL/SEC/CEN/BV-14-C,
Central Receiving unexpected PDU during encryption start
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
Add support for both LL_REJECT_IND and LL_REJECT_EXT_IND when waiting
for the the response to the LL_ENC_REQ and LL_START_ENC_REQ.
Add unit test to test both LL_REJECT_IND and LL_REJECT_EXT_IND as
responses to LL_ENC_REQ.
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
Chose correct rejection PDU based on features supported on remote peer
when rejecting due to missing LTK.
Update unit test setup with faking that a feature exchange procedure
has run.
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
Terminate connection with a MIC failure if an unexpected control PDU
is received during the Encryption Start procedure.
Add unit test inspired by Bluetooth Qualification test
LL/SEC/PER/BI-05-C,
Peripheral Receiving unexpected PDU during encryption start
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
This adds suport for validation of received PDUs before they are
pass further to LLCP state machines. If PDU size is invalid it is
rejected with LL_UNKNOWN_RSP.
This was affecting following qualification test cases:
LL/PAC/PER/BI-01-C
LL/PAC/CEN/BI-01-C
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Instead of waiting one connection interval, as a result of the state
change, perform the check for instant already on reception of
CONNECTION_UPDATE_IND
Signed-off-by: Erik Brockhoff <erbr@oticon.com>
