Increase the supported receive state count to 4, as
several on-market device have at least 2 and sometimes
more.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If pa_sync_past returns 0 then that means we are ready to
sync to past, and the BT_BAP_PA_STATE_INFO_REQ state should be set.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
stm32l1_disco board from STMicroelectronics has eeprom and watchdog.
Enable those peripherals.
Tested using:
1. samples/drivers/eeprom
2. samples/drivers/watchdog
Signed-off-by: Maxin John <maxin.john@gmail.com>
LPTIM4 is selected, since it is used only for internal timing
and it doesn't support output/input
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
The LL_APBx_GRPn_ReleaseReset clears reset bit in RCC,
however this bit is reset by default. Code that set
this bit was removed in previous commit
0856e99155
Keepint the autonomous clocks for STM32U5 family.
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
Magic constants throughout the code made this difficult to reason about,
especially with two different units of measurement (bytes and words) at
play.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The RX FIFO size is in words, so needs to be subtracted from the total
memory size *after* it's divided by 4.
Fixes#70789.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This adds DT aliases for LED and button used in recovery mode of the
MCUboot bootloader, on the 'nucleo_wb55rg' board.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add nrfx_grtc related entries that were introduced in nrfx 3.4.0,
especially NRFX_GRTC_CONFIG_AUTOSTART that should be by default
set to 1.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds support for custom commands to be executed during the
build of an llext target. The commands can be executed at different
points in the build process:
- PRE_BUILD: Before the llext code is linked.
- POST_BUILD: After the llext code is built, but before packaging
it in an .llext file.
- POST_PKG: After the llext file has been created.
Note that PRE_BUILD is not supported for ARM targets, as in that case
object files are used directly and there is no actual linking step.
The commands can be added using the new add_llext_command() function.
An example usage of it, along with some target properties, is added to
the hello_world test case.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Remove the C_FLAGS argument from add_llext_target() and add a set of
functions to configure the compilation and linking of an llext using
the same API of the target_* functions.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
This change reworks the Xtensa support in llext to use CMake's native
shared library support, instead of manually running "gcc -shared".
This change minimizes the differences in llext handling by defining
appropriate CMake targets for the different architectures.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
When CONFIG_LLEXT is enabled, the Zephyr platform needs to enable dynamic
library support. This is done by setting the `TARGET_SUPPORTS_SHARED_LIBS`
property to `TRUE` in the global property scope.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Add entry for st7796s to display build_all test, so that the controller
driver will be built by CI.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add driver for ST7796s display. This is a MIPI DBI display controller,
with a frame memory of 320x480x18 pixels. Support for 4 wire SPI mode is
implemented using the MIPI DBI API.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add binding for sitronix ST7796s, a MIPI DBI display controller
supporting up to 320x480 displays at 18 BPP
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
add myself as maintainer for hawkbit and
change the status of hawkbit from odd fixes to maintained
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
The SparkFun Pro Micro header pins are numbered D1, D0, GND, ... from top
left whereas the SparkFun Pro Micro RP2040 and the Adafruit KB2040 boards
are using gpio 0, 1, GND, ... , so the pro_micro: connector gpio-map of
these boards should reflect that.
Graphical Datasheet for SparkFun Pro Micro RP2040:
https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf
Graphical Datasheet for SparkFun Pro Micro:
https://cdn.sparkfun.com/assets/f/d/8/0/d/ProMicro16MHzv2.pdf
Pinout of the Adafruit KB2040:
https://learn.adafruit.com/assets/106984
Please note that the KB2040 uses CircuitPython pin labels D0, D1 which does
not seemt correspond to the Arduino labels D0 and D1 used by the Pro Micro.
Signed-off-by: Daniel Irekvist <ulmanyar@gmail.com>
Do not build threading support when CONFIG_MULTITHREADING=n is set and
move needed calls to a new file with the changes needed instead of the
ifdef party in sched.c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some toolchains cannot create shared objects for Xtensa, with them we
have to use relocatable objects. Add support for them to llext.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
An overlay file was wrongly added to a target_sources call, this has
now been corrected.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Warn about potential device tree errors for cases when driver's
client tries to configure a pin as GPIO but which is not
in GPIO mode.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Was getting the error "parse error: expected number or parenthesized
expression" when trying to compile with the
-DSHIELD=seeed_xiao_expansion_board flag. It looks like INPUT_KEY_0
was missing the necessary include file so I added it in.
Signed-off-by: Graham Harrison <graham.harrison@axcendcorp.com>
Correct various small edge-case behaviors that have been accidentally
introduced in the http_client.
- http_client_req no longer incorrectly returns -ETIMEDOUT on NULL HTTP
resonse. -ETIMEDOUT is now only returned when the underlying TLS
socket times out.
- http_client_req now returns -ECONRESET upon incomplete (but non-NULL)
HTTP response. The request callback is no longer called in this case
(as with any other error state).
- http_wait_data has been refactored slightly to increase clarity.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
It is impossible to perform flash reads during a flash write. When the
data to write to flash lies in the flash itself, it is buffered in ram
before writing.
Signed-off-by: Lukas Gehreke <lk.gehreke@gmail.com>
Update system pm diagram to reflect recent changes in the subysystem.
Use graphviz to create this new diagram.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Since GTBS and GMCS in both spec definitions and
in the Zephyr implemenation are notably different,
it is worthwhile pointing these out in the documentation
for content control.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This commit removes the `Kconfig.core` file. It's been largely unused, and
the only symbol it provides (`RISCV_CORE_E31`) overlaps with the SoC-layer
provided `SOC_SERIES_SIFIVE_FREEDOM_FE300`.
As of date, the only SoC that uses the E31 core in Zephyr is the FE310 SoC.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
If the packet cloning fails (can easily happen when working with
loopback interface and when having low net_buf count), then
print a warning to the user. Error could also be possible but
as the situation might correct itself in this case, the warning
should be enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
