Add Bluetooth 5.1 Direction Finding HCI command:
HCI_LE_Read_Antenna_Information handling to Host.
Add wrapper function to handle send the command
and receive response from Controller.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Document the behavior of the bt_conn_le_conn_update API when the
local device is the peripheral role.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Introduce a support kconfig for controller ECDH command support.
Default to host ECDH emulation in combined host controller build
where the controller does not support these commands.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove the range on the setting the bluetooth BT_RX_STACK_SIZE.
This range prevents setting the RX stack size lower than 1024,
which depending on the application is too high.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
A build assert in dummy.c lists the following requirement:
[...] receive thread priority shall be higher than the Bluetooth
Host's Tx and the Controller's receive thread priority.
This is required in order to dispatch Number of Completed Packets
event before any new data arrives on a connection to the Host threads.
The drivers uses a priority that is equal to the Host TX thread,
and since they don't use the CONFIG define that is only available
to the controller then this BUILD_ASSERT will not catch the
requirement.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This adds CONFIG_BT_CONN_DISABLE_SECURITY which can be used to disable
security checks for incoming requests enabling to test accessing GATT
attributes and L2CAP channels that would otherwise require
encryption/authentication in order to be accessed.
It depends on BT_TESTING to indicate to the users that this is a
testing feature which shall not be used in production.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix host RX thread being deadlocked. The deadlock occurs because the
RX thread is stuck waiting in conn_tx_alloc with K_FOREVER but if the
connection is disconnected only the RX thread can unblock it in the
handling of the disconnect event.
This commit fixes this deadlock by splitting the processing of the
disconnected event into two parts.
The part needed to unblock the RX is to release resources held by
unack'ed TX packets and mark the connection state as not connected
anymore.
The RX thread waiting for free_tx fifo and the TX thread waiting for
the bt_dev.le.pkts semaphore will both check the connected state after
having acquired them and will abort if disconnected.
The rest of the processing will be handled at normal RX thread
priority like normal.
Move the bt_recv_prio handling to the Bluetooth host when the host
has defined its own RX thread (CONFIG_BT_RECV_IS_RX_THREAD=n).
If the HCI driver has the RX thread (CONFIG_BT_RECV_IS_RX_THREAD=y),
then the responsibility to call bt_recv and bt_recv_prio correctly
falls to the HCI driver.
The helper function bt_hci_evt_is_prio() is replaced with
bt_hci_evt_get_flags() so that the HCI driver can do this correctly.
This decision to replace was made so that existing HCI drivers
maintained out-of-tree will fail at compile time with the new system.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bluetooth: host: Move bt_recv_prio to host when RX thread is defined
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add warning about enabling the options below so that users are
aware that this is a security risk.
- CONFIG_BT_DEBUG_SMP
- CONFIG_BT_DEBUG_KEYS
- CONFIG_BT_OOB_DATA_FIXED
- CONFIG_BT_USE_DEBUG_KEYS
- CONFIG_BT_STORE_DEBUG_KEYS
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add application control of initiating phy change procedure and it's
parameters.
The reasons for allowing the application control over the PHY:
- Allow changing to Coded PHY.
- Application may change PHY to react to changes in environment
to balance throughput and range.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add application control of initiating data length procedure and it's
parameters.
The reasons for allowing the application control over the data length:
- Bandwidth control adjusted based on number of active connections.
- Changing data length before switching to coded phy.
- Applying workarounds for interoperability problems.
- Controlling order of ATT MTU and data length procedures.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add Kconfig option so that the application can disable automatic
initiation of the data length procedure. This is symmetric with the
PHY auto initiation kconfig option.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extends the bt_conn_le_create_param struct to provide the option
to set a custom timeout for the initiation of the connection.
The logic for the default values of window_coded and interval_coded
were moved to conn.c in order to resolve all defaults for the
create_param struct at a single location.
Timeout is not added as a parameter to the BT_CONN_LE_CREATE_PARAM
macro due to the expectation that CONFIG_BT_CREATE_CONN_TIMEOUT
will be the typical value that users will expect.
Fixes#23468
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Update buffer sizes needed when advertising extensions is enabled. Since
BT_RX_BUF_LEN is used for the HCI command as well we need to fit the
full 255 bytes of the Set Extended Advertising Data or Scan Response
Data plus the 3 byte header of an HCI command.
For the discardable buffer size we need to fit the LE Extended
Advertising Report event, which can be a maximum of 255 bytes plus the
2 byte header of an HCI event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The commit e85dd8af5d changed the way the BT_ECC Kconfig option
is enabled, however it got the dependency wrong. The dependency should
only look at BT_SMP_OOB_LEGACY_PAIR_ONLY if BT_SMP was also enable.
This broke e.g. the build of the mesh_demo app for the BBC
micro:bit since the memory consumption jumped up by roughly 2k.
This patch fixes the issue, and in the same go makes the Mesh handling
consistent by also using a conditional default rather than select.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Added CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY option that completely disables
all legacy and SC pairing modes(except for Out of Band) and frees the
memory previously used by these.
Added CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY option that force rejects
pair requests that lead to legacy Just Works or Passkey pairing.
Signed-off-by: Iván Morales <ivan98ams@gmail.com>
Corrected configuration of BT_HCI_RESERVE for the RPMsg HCI driver.
This change fixes the following assert:
[net_buf_simple_headroom(buf) >= len] @ ZEPHYR_BASE/subsys/net/buf.c:881
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds a new option CONFIG_BT_SMP_USB_HCI_CTLR_WORKAROUND
to support USB HCI controllers that sometimes send out-of-order HCI
events and ACL Data due to using different USB endpoints.
Enabling this option will make the master role not require the
encryption-change event to be received before accepting
key-distribution data.
It opens up for a potential vulnerability as the master cannot detect
if the keys are distributed over an encrypted link.
Fixes: #22086
Signed-off-by: François Delawarde <fnde@oticon.com>
Document why a privacy-disabled scanner will not notify about directed
advertising reports. This is the default behaviour of the
privacy-disabled scanner. In order to receive the reports the option
BT_SCAN_WITH_IDENTITY must be enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Similar to pairing_confirm this callback is called each
time a peer requests pairing, but for all types of
pairings, except SSP. The pairing req/rsp information is
passed as a parameter so the application can decide
wheter to accept or reject the pairing.
Fixes: #21036
Signed-off-by: Martin Rieva <mrrv@demant.com>
Moves the Mesh AES-CCM module out into a separate module, to make it
accessible from other subsystems. Adds the new CCM API in
include/bluetooth/crypto.h along with the bt_encrypt functions.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Handle initiator role when RPA timeout expires. For direct connect
establishment procedure we make sure the RPA is refreshed when starting
initiator and limit the timeout to the RPA timeout.
For auto establishment procedure we cancel the initiator and restart it
again in the connection complete event that is generated when canceling
an initiator.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix error in calculation of the minimum discardable buffer size. For
the LE Advertising Report the maximum payload is 31 bytes plus
additional data in the event gives an event size of 41 bytes (given that
num_reports is 1). Since this is a meta event we need to include the
sub-event code, plus the event header of 2 bytes. Total of 44 bytes.
This is a regression from afa9c42d75 where we forgot th 1 byte for the
RSSI that is appended after the data. Easy to miss since it is not part
of the struct.
Fix error in calculation of the num complete buffer size. Here we forgot
to include the 2 byte event header.
This is a regression from 89981b07c8.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add option to set the size of the discardable buffer pool. This saves
memory for the MESH use case where we expect a large number of advertise
reports.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Make remote features and remote version accesible to the application
through the bt_conn_get_remote_info object. The host will auto initiate
the procedures. If the procedures have not finished with the application
calls bt_conn_get_remote_info then EBUSY will be returned.
The procedures should finish during the first 10 connection intervals.
Signed-off-by: Sverre Storvold <Sverre.Storvold@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
If NET_L2_BT is enabled we need enough acl_in_pool needs to be big
enough to contain a full IP packet since that is no longer processed by
RX thread buffer would be queued to syswq to reassemble the SDU.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Added configuration for accepting pairing requests only if both devices
has bonding flag set in order to reject other devices at an early stage,
thus leaving more chance for devices expected to bond.
With the CONFIG_BT_BONDING_REQUIRED flag the device only accept pairing
requests if it has CONFIG_BT_BONMDABLE set and the device requesting
pairing has Bonding_Flags field set to Bonding (0x01) in its AuthReq.
Note: When using bt_set_bondable(false) pairing requests will be
rejected when CONFIG_BT_BONDING_REQUIRED is set.
Signed-off-by: Martin Rieva <mrrv@demant.com>
Fixed handling of HCI events in the HCI driver over RPMsg. Now,
the driver makes use of discardable buffer pool when allocating
memory for certain HCI event types (e.g. Advertising Report Event).
Applications that are flooded with Advertising Reports will run
much better after this change (e.g. Mesh applications).
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This is a moderate redesign of the pending TX packet handling that
aims to eliminate potential deadlocks between the TX thread and the
system workqueue thread. The main changes are:
- TX context (bt_conn_tx) is allocated during buffer allocation, i.e.
not in the TX thread.
- We don't allocate a TX context unless there's an associated
callback. When there's no callback simple integer counters are used
for tracking.
- The TX thread is no longer responsible for TX callbacks or
scheduling of TX callbacks. Instead, the callbacks get directly
scheduled (k_work_submit) from the RX priority thread.
- CONFIG_BT_CONN_TX_MAX defaults to CONFIG_BT_L2CAP_TX_BUF_COUNT,
and in most cases wont need changing. The value now only indicates
how many pending packets with a callback are possible.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BT_HCI_TX_STACK_SIZE is carefully calculated from other
options. When those options change, e.g. from a menuconfig update, it
is important that the stack size is re-calculated, but it is not when
there is a prompt.
Therefore, make the prompt conditional such that the previously set
value is only used when it has been explicitly configured to be so.
Now users can still change the value through menuconfig and prj.conf,
by also enabling <option>_WITH_PROMPT, but when the value is
calculated by the defaults, it will continue to be calculated by
defaults instead of inheriting the intial value.
This is AFAIK a novel approach, but testing has shown that it gives
the users the behaviour they want, at the cost of some boilerplate of
course. This pattern can be applied to other options if it proves to
work as intended.
Alternatively one could remove the prompt, but then it would no longer
be possible to override the value through menuconfig.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This commits adds a BT_SETTINGS_CCC_LAZY_LOADING option to allow for
CCC settings to be loaded on demand when a peer device connects in
order to reduce memory usage.
Signed-off-by: François Delawarde <fnde@oticon.com>
Disallows all unauthenticated pairing attempts made by the
peer where an unauthenticated bond already exists.
This would enable cases where an attacker could copy the peer device
address to connect and start an unauthenticated pairing procedure
to replace the existing bond. Now in order to create a new bond the old
bond has to be explicitly deleted with bt_unpair.
Added option to disable this rule in order to maintain backwards
compatibility in case this behavior is accepted.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Key overwrite feature allows to overwrite old pairing key
records when key storage is full and a new pairing request occurs,
or new keys are distributed. If enabled when key storage is full and
a keys storage slot is requested, the oldest keys added will be
removed. So new devices can be paired with no limitations and no need
to determine, which devices should be unpaired to free key storage
space explicitly in application. To enable the feature set
CONFIG_BT_KEYS_OVERWRITE_OLDEST=y.
Oldest keys are determined by minimum value of up-counting aging
counter. If you set CONFIG_BT_KEYS_SAVE_AGING_COUNTER_ON_PAIRING=y
aging counter values will be updated each time the secure connection
is established. This might increase flash wear out if at least two
secure connections are established and shut down periodically. When
the option disabled aging counter is still updated on each new secure
connection, but not stored to flash.
Signed-off-by: Sergiy Nikolayenko <sergiy_nikolayenko@jabil.com>
Remove the
# Omit prompt to signify a "hidden" option
comments that appear on some symbols. They seem to have been copy-pasted
at random, as there are lots of promptless symbols that don't have them
(that's confusing in itself, because it might give the idea that the
ones with comments are special in some way).
I suspect those comments wouldn't have helped me much if I didn't know
Kconfig either. There's a lot more Kconfig documentation now too, e.g.
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Keep some comments that give more information than the symbol having no
prompt.
Also do some minor drive-by cleanup.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Some modules use snprintk to format the settings keys. Unfortunately
snprintk is tied with printk which is very large for some embedded
systems.
To be able to have settings enabled without also enabling printk
support, change creation of settings key strings to use bin2hex, strlen
and strcpy instead.
A utility function to make decimal presentation of a byte value is
added as u8_to_dec in lib/os/dec.c
Add new Kconfig setting BT_SETTINGS_USE_PRINTK
Signed-off-by: Kim Sekkelund <ksek@oticon.com>
Enable possibility to configure time a slave will wait until
start of connection parameters update procedure after BT connection
is established.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Made BT_HCI_TX_STACK_SIZE configurable and added BT_HCI_ECC_STACK_SIZE.
These changes are necessary to allow vendors to adjust for other
achitectures.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Allow SMP debug keys to behave in the same way as normal keys, in order
to debug with encryption and Bluetooth sniffer the exact way it behaves
when not using debug keys.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add whitelist support in the bluetooth host.
Supported features:
- Advertising with whitelist on scan requests, connect request ,or both
- Scanning with whitelist
- Creating connections using a whitelist (Auto connection procedure).
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
subsys/bluetooth/host/Kconfig.gatt is already sourced within an
'if BT_CONN' in subsys/bluetooth/host/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fixed error 'The int symbol BT_DISCARDABLE_BUF_COUNT is being evaluated
in a logical context somewhere'.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Rename the controller Kconfig option BT_LL_SW to
BT_LL_SW_LEGACY in preparation towards switch to new Link
Layer implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Having this option disabled, MITM flag state can be controlled by
bt_conn_security state. This option is enabled by default to not
change the current implementation behavior.
Related to SM/MAS/SCPK/BV-01-C.
Fixes#17463
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
We've already got GATT services in subsys/bluetooth/services so
subsys/bluetooth/mesh is a more natural place. Aditionally this aims
to fix the Kconfig dependencies to be able to use mesh together with
BT_CUSTOM (i.e. a custom, potentially non-HCI, host stack).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Introduce a separate buffer pool for events which the HCI driver
considers discardable. Examples of such events could be e.g.
Advertising Reports. The benefit of having such a pool means that the
if there is a heavy inflow of such events it will not cause the
allocation for other critical events to block and may even eliminate
deadlocks in some cases.
Also update all mesh samples not to specify explicit RX buffer counts
anymore. Instead, create appropriate defaults in Kconfig so that we
only need to override this in the app for cases like the bbc:microbit
with limited memory.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
