This command will be used to test if model can properly send
segmented and unsegmented messages to a given destination address.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Those commands will be used for qualification purposes to verify
the functionality of Mesh Health Model.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This event is needed for qualification purposes to verify functionality
of Mesh Network layer.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This introduced two BTP events to indicate provisioning link state.
This is needed for testing purposes, since PTS requests tester to
confirm link state.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This will be used for verification in GATT test cases.
This procedure is used query local GATT Server for attributes
based on given search pattern. Attributes can be searched using
Attribute Handle range and Attribute Type.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Attribute Value Changed Event will be used to indicate characteristic
or descriptor value change in local GATT Server database.
Event will be triggered when PTS performed ATT Write operation
successfully.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This moves discovery logic to the tester application.
BTP Start Discovery command flags have been extended with
"Use observation procedure" bit.
For now, Tester can search for devices in limited/general discoverable
mode or those that are broadcasters by setting corresponding flag bits.
Change-Id: I7142e8fdf40a9081787538e433067335d3ee0564
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This adds commands to the Bluetooth Testing Protocol for L2CAP.
Change-Id: Ie9ea180c4db62c238ce1450e5714ffd7b0ca2f5f
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
Before sending any command, the tester shall wait for this event
indicating that IUT is ready to accept first BTP command.
This is needed, because some devices need more time to initialize
their stacks, so that the first BTP command can be lost.
Change-Id: I92d1c6ea8be905734037eb29f7f270a70ab1583e
Signed-off-by: Mariusz Skamra <mariusz.skamra@gmail.com>
Some IUTs may have predefined attributes in db which aren't take into
consideration while building via tester database. BTP clients should
know about such attribute handle offset change. After start server
we're sure that none of attributes will be added since zephyr db is
constant.
Change-Id: Ia2c6edaa7a2f3ca4a9c88fe00122c808a529dadb
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Most iuts data base are intended to have its attribute database builded
in sequence and its constant (except attribute values, parameters,
permissions). Patch allows btp specification to cover also devices
which cannot assign an ID right after issuing add attribute command or
set attribute component (which points to defined attribute ID).
Change-Id: Ie8e5ed223609cca2b6e3fb8444065f33b1408142
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Now start discovery GAP function interprets scan type flags (active,
passive) and starts discovery with specific LE scan parameters.
Change-Id: Iecb942e24d68790966afe893d3543433c33192dc
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
This patch makes opcodes to be in the sequence.
Supported commmands is form now uint8_t array, so this resolves
the problem with endianess as well.
Change-Id: I602a58081948dbbf5e0d83cbb12a118a5990b9f8
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This splits Authorization permission to Read with Authorization
and Write with Authorization.
Some attribites may be readable with no authorizarion, but writable
with authorization defined by a higher layer specification or be
implementation specific (eg. Server Characteristic Configuration
Descriptor).
Change-Id: I341a7095c1e8db1dea92cdeebf76c5a2307a49a1
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
Move all bluetooth testcases to tests/ and change Makefiles
accordingly where applicable.
Also fix Makefile to make some variables overridable and reduce
level of whitelisting in testcase.ini.
Change-Id: Ia71ee1fbbb238c45280b1e3c4747ca2f748f5263
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2016-02-11 18:00:35 +00:00
Renamed from samples/bluetooth/tester/btp_spec.txt (Browse further)
