Fix issue where a new connection with the same peer would use the CCC
from from first connection, despite different local identity.
Since there is no CCC for the new connection yet this caused the
application to think that CCC was enabled but the remote device had not
yet subscribed.
Fix this issue by making the id as an input to the peer address check
function. This will force us to make the check every time. This commit
might also fix similar issues not yes discovered as the ID check was
missing in a few other places as well.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename the acl buf context id to index since to avoid confusing it with
the conn object ID parameter. Especially the bt_conn_lookup_id function
was creating confusion.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix ticker resolve collision implementation for incorrect
ticks accumulation and the calculation of next period.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix a race condition in radio abort requested by flash
driver. It is possible that during abort function execution,
PPI setup to start radio fires. Hence, check explicitly in
cleanup function for radio being in use and disable it.
Fixes#22945.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use the old ticker compatibility mode implementation as
default for nRF5x Series SoCs.
Fixes#22926.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Avoid the HCI-USB race condition where HCI data and HCI events can be
re-ordered, and pairing information appears to be sent unencrypted.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix to remove assertion failure check on detecting invalid
packet sequence used by peer central and that no non-empty
packet was transmitted.
Fixes#22967.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix issue where an invalid (all zeroes) hash was written to settings
storage on reset. This caused the old value to written to zeroes, before
being written back to it's original value again immediately after.
This causes excessive flash wear.
This happens because the check if (k_delayed_work_remaining) returns the
amount of time until the work will execute. When that time has run out
the time is zero, but the work has not yet been executed.
We then write the invalid hash to flash, and then once the work-item
executes it will write the correct value.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
- avoid spourious radio interrupts by fixing ISR set,
waiting for idle, command configuration
- adjust counter to account for missing increment
- change preemption instant to avoid missing the deadline in LLL
- decrese EVENT_JITTER_US and
EVENT_TICKER_RES_MARGIN_US (same as Nordic)
Continuous scanning and connections are working fine now.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Created unit tests for the encryption and decryption functions.
Tested with the peripheral and with central_hr samples.
Due to latency of CAUv3 when used as CCM inline accelerator
only one of the PDU can be encrypted/decrypted within an
bilateral exchange M->S + S->M in a connection event.
If the RXed PDU is encrypted, the TXed PDU must be empty
with More Data if there is data in the LLL queue.
The TXed PDU will be encrypted when an empty PDU is RXed.
Signed-off-by: Cristi Caciuloiu <cristian.caciuloiu@nxp.com>
Fix regression due to addition of conditional compilations
while porting the privacy feature from legacy to split
controller.
Fixes#22801.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Backport of https://github.com/apache/mynewt-nimble/pull/724
Mesh spec 1.0.1 changes proxy disabling behavior to only affect the
relaying from proxy nodes. Previously, disabling proxy would shut down
all proxy and node activity.
Tweaks from the original commit:
- Removed redundant call to bt_mesh_adv_update() in gatt_proxy_set()
- Removed invalid ref to 4.2.11.1 in node_identity_set()
---
According to Mesh Profile Spec 1.0.1, Section 4.2.11:
"If the Proxy feature is disabled, a GATT client device can connect
over GATT to that node for configuration and control. Messages from
the GATT bearer are not relayed to the advertising bearer."
Moreover some notes have been removed from the spec compared to
version 1.0:
Mesh Profile Spec 1.0, Section 4.2.11:
"Upon transition from GATT Proxy state 0x01 to GATT Proxy state 0x00
the GATT Bearer Server shall disconnect all GATT Bearer Clients."
"The Configuration Client should turn off the Proxy state as the last
step in the configuration process."
Mesh Profile Spec 1.0, Section 4.2.11.1:
"When the GATT Proxy state is set to 0x00, the Node Identity state
for all subnets shall be set to 0x00 and shall not be changed."
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
SC config data is no longer stored within the CCC config itself
therefore it must be cleared separately.
Fixes#22539
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GATT data shall not be considered conditional to BT_SETTINGS since
the data is stored in RAM it must also be cleared when unpairing.
Fixes#22514
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
smp_pairing_complete does actually clears flags so setting
SMP_FLAG_TIMEOUT must come after that.
Fixes#22786
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix bt_gatt_indicate using the wrong attribute pointer when a uuid was
provided as input.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename the scan recv callback info struct so that it reflects that it
is part of the scan recv callback. This will make it consistent with
future plans for advertising callbacks.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix the scanner using the advertiser identity instead of the scanners
identity, scanner always use BT_ID_DEFAULT.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Corrected configuration of BT_HCI_RESERVE for the RPMsg HCI driver.
This change fixes the following assert:
[net_buf_simple_headroom(buf) >= len] @ ZEPHYR_BASE/subsys/net/buf.c:881
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This can happens if for example the remote peer have the initial credits
set to 0 which would cause bt_l2cap_chan_send to fail instead of just
queue the packets until more credits are given.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Data transmission was paused when PHY update request control
PDU was enqueued in ULL. If there was pending data PDU in
ULL that was not enqueued towards LLL, this caused
transmission to stall.
Move the tx pause due to PHY update request/response being
enqueued to pre_tx_ack callback, this way all pending PDUs
in ULL is enqueued to LLL.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The existing stack_analyze APIs had some problems:
1. Not properly namespaced
2. Accepted the stack object as a parameter, yet the stack object
does not contain the necessary information to get the associated
buffer region, the thread object is needed for this
3. Caused a crash on certain platforms that do not allow inspection
of unused stack space for the currently running thread
4. No user mode access
5. Separately passed in thread name
We deprecate these functions and add a new API
k_thread_stack_space_get() which addresses all of these issues.
A helper API log_stack_usage() also added which resembles
STACK_ANALYZE() in functionality.
Fixes: #17852
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If CONFIG_BT_CTLR_CONN_RSSI is enabled, then lll_conn.h should
be included as well. Otherwise, struct lll_conn is unknown
at the compile unit level. This has been reproduced by
compiling the hci_uart sample, where the following error occurs:
lll_adv.c: In function 'isr_rx_pdu':
lll_adv.c:722:13: error: dereferencing pointer to incomplete
type 'struct lll_conn'
lll->conn->rssi_latest = radio_rssi_get();
^~
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Until now the choice of reliable sending (segmented messages with
acks) was implicitly dependent on the size of the payload. Add a new
member to the bt_mesh_model_pub to force using segment acks even when
the payload would fit a single unsegmented message.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix uninitialized advertiser rl_idx used to check own identity
in CONNECT_IND received for directed advertisements.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor the handling of network nodes and their keys into a separate
Mesh Configuration Database (CDB). This, not only creates a separation
of the local node and the other nodes, but also makes it possible to
implement functions to manage the whole, or at least parts of the mesh
network.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
This API will be deprecated in favor of the new API that clearly
specifies whether it works on logical or physical levels.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Some compilers can't resolve the conditional if/else/else construction
in ull_conn event_len_prep function, and fail with an 'uninitialized
variables' error. The change has no functional impact.
Signed-off-by: Morten Priess <mtpr@oticon.com>
BT_CTLR_SETTINGS should not depend on BT_SETTINGS as this will prevent
using settings system in the controller in a controller only build.
(BT_SETTINGS depends on BT_HCI_HOST)
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
This commit adds a new option CONFIG_BT_SMP_USB_HCI_CTLR_WORKAROUND
to support USB HCI controllers that sometimes send out-of-order HCI
events and ACL Data due to using different USB endpoints.
Enabling this option will make the master role not require the
encryption-change event to be received before accepting
key-distribution data.
It opens up for a potential vulnerability as the master cannot detect
if the keys are distributed over an encrypted link.
Fixes: #22086
Signed-off-by: François Delawarde <fnde@oticon.com>
Directed advertising timeout was dropped in the host due to
not being able to find a pending connection. Host used the
role parameter from the error event parameters which has
been earlier zero-ed out.
Regression introduced in commit a0349689ff ("Bluetooth:
host: Fix conn object assigned to wrong connection")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When starting a non-connectable advertiser and an active scanner is also
using NRPA address then this use-case should be supported. A new
advertiser that is non-connectable should have a fresh NRPA address
every time it is started, so we must refresh the NRPA used by the active
scanner.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When advertiser is disabled we should update the random address for both
passive and active scanner back to an NRPA. But this command will fail
because the if the scanner is an active scanner, we must disable and
re-enabled the active scanner after setting the random address.
This behavior should not be there when scanner is configured to scan
with identity address.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Document why a privacy-disabled scanner will not notify about directed
advertising reports. This is the default behaviour of the
privacy-disabled scanner. In order to receive the reports the option
BT_SCAN_WITH_IDENTITY must be enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Prevent the advertiser from overwriting the passive scanners identity
address when the scanner has been configured to scan using the identity.
In this case the LE Set Random Address command would not prevent the
address from being overwritten. So instead we explicitly stop it in the
host.
Also fix original code function not working at all since the first
if statement was should had a bad check. Resulting in it always
returning success.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Drop directed advertiser reports when the passive scanner should have
been using the NRPA address. The advertiser has overwritten the NRPA
with it's identity address instead and a peer is sending directed
advertiser packets to it.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When privacy is disabled by default the scanner still protects it's
identity with the use of NRPA addresses. We should not set the identity
address for the passive scanner unless the Kconfig option to scan with
the identity has been enabled.
This makes passive scanner behave the same way as an active scanner
since none of them will report directed advertising reports towards
the scanners identity.
This also enables the advertiser to switch out the random address which
is needed for the Bluetooth Mesh LPN case.
Fixes#22088.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Add pairing support callback to print remote pairing features when this
option is enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Similar to pairing_confirm this callback is called each
time a peer requests pairing, but for all types of
pairings, except SSP. The pairing req/rsp information is
passed as a parameter so the application can decide
wheter to accept or reject the pairing.
Fixes: #21036
Signed-off-by: Martin Rieva <mrrv@demant.com>
In a combined build where bt_rand functions is implemented in the host
the RPA module should not use the bluetooth rand function since the RPA
module is common for host and controller.
Having the controller call the the host only to go through HCI back into
the controller would not be a good idea.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix infinite recursion in host-based bt_rand function. This would call
HCI LE Random Number command, which would in turn call bt_rand, causing
an infinite recursion.
bt_rand -> prng_reseed -> BT_HCI_OP_LE_RAND -> le_rand -> bt_rand
To solve this issue the controller should avoid doing calls into the
host, so all calls to bt_rand in the controller should be replaced with
a call to a controller function.
Fixes#22202
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix LE Create Connection command giving out of range parameters to the
controller, this came back as 0x30 (Out of Range Parameters) status code
on the command from the controller.
This appears to be the min and max CE parameters in the command.
Revert back memset from 137f704064
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
