The OpenTitan watchdog driver is a watchdog driver that can be configured
with two stages: a watchdog "bark", which generates an interrupt, and a
watchdog "bite", which resets the system. The two-stage watchdog can be
enabled by setting CONFIG_WDT_MULTISTAGE=y. Otherwise, the driver
functions as a single-stage watchdog.
A callback function may be set for the bark interrupt through the
wdt setup interface, but will only be used if the two-stage watchdog is
enabled. It must be configured for the first watchdog stage.
The driver controls only the watchdog portion of the OpenTitan AON timer.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
Add a driver for the Xilinx AXI Timebase WDT logic core. This can be
instantiated on various Xilinx FPGA-based platforms such as the
Digilent Arty, although it is not part of the default image used with
the Zephyr board configuration.
The driver can also optionally implement the HWINFO API to allow
determining whether the last system reset was initiated by the WDT.
Since this is a standalone IP core which could be used a variety of
configurations, this support is optional in case the system/SoC it is
used with already implements this support.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Added a new watchdog driver which can handle a multiple wdt_dw instances
and can control the pause signal.
The mlt platform has three designware watchdogs, one for each core.
I decided to create a separate intel watchdog driver for the following
reasons:
1. All three devices share the same interrupt number. Each watchdog reports
an interrupt to the core to which it has been assigned. The same interrupt
number cannot be used by multiple devices in the device tree. So, it would
be assigned to only one device. The other dw watchdog devices would use
this assignment, even though it would not be described for them in the dt.
The interrupt handler function in dw watchdog checks the interrupt flag.
If the interrupt was connected to the first watchdog, and the second or
third watchdog signal an interrupt, the interrupt handler of the first
device would ignore it because it would not have set the interrupt flag.
The watchdog device don't knows anything about the existence of the others
devices.
2. The designware watchdog only supports a hardware pause signal. It cannot
be paused programmatically. On the mtl platform, there is a separate group
of control registers for all per-core watchdogs. There are GPIO-like
registers that allows control of a hardware pause signal for subordinate
watchdogs. This separate block is shared by all three watchdogs.
3. The base addresses of the subordinate watchdogs are read from the
aforementioned control registers. As a result, in the device tree we have
only one base address for the intel watchdog, which points to the pause
control registers and containing the base addresses of the subordinate
devices.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This adds a basic Intel TCO watchdog driver. The driver doesn't support
windowed timeouts (a non-zero window.min value) or callbacks. The driver
currently assumes TCO version 6, which can be found e.g. on Elkhart Lake
and Raptor Lake platforms. The driver also expects the TCOBA base
address to be specified through DTS, rather than doing runtime lookup
(using e.g. ACPI or PCIe).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add support for the TI TPS382x series. The IC has an input pin which
should be toggled by the processor and a output pin which should be
connected to the RESET input of the processor. The timeout is not
configurable.
This device can be used by devices which does not have any internal
hardware watchdog device.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
This patch adds watchdog driver for Renesas Smartbond SOCs.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
New Zephyr WDT driver for TI CC13xx/CC26xx family.
Supports interrupts & MCU soft reset on timeout.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Update watchdog drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
This adds basic support for the watchdog timer on the RP2040 MCU and
Raspberry Pi Pico development board
Signed-off-by: Jamie McCrae <spam@helper3000.net>
All the watchdog drivers are based on devicetree and we dont utilize
HAS_DTS_WDT anywhere so we can remove it.
Signed-off-by: Kumar Gala <galak@kernel.org>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Added watchdog implementation which is using counter device
to implement watchdog driver API. Watchdog timeout is called from
counter interrupt context. Some counter implementations support
using ZLI interrupt level which can be use here as well. Watchdog
like this can be used along hardware watchdog to cover for its
limitations, i.e. Nordic watchdog resets unconditionally after
62uS after triggering watchdog interrupt. It is not enough time
to dump logging data.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
In npcx7 series, the Timer and Watchdog module (TWD) generates the
clocks and interrupts used for timing periodic functions in the system.
It also provides watchdog reset signal generation in response to a
failure detection.
The CL also includes:
— Add npcx watchdog device tree declarations.
— Zephyr watchdog api implementation.
— Add Watchdog definitions for npcx7 series in
tests/drivers/watchdog/wdt_basic_api/src/test_wdt.c for
supporting test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This reverts commit 382e6fbccf.
Disabling watchdog at boot breaks watchdog API contract. Production
firmware should never ship with the option enabled. Unfortunately, this
is dangerosly easy to overlook. If left enabled, in the best case, it
will degrade functionality of the subsystem. In the worst case it
will leave watchdog permanently disbled.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Watchdog type is found on e.g. Pearl/Jade Gecko, often
more than 1 is present.
Driver supports timeout and (minimum) window configuration
and reset or timeout interrupt support for now.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
This commit consolidates the meaning of WDT_DISABLE_AT_BOOT option as
"disabling watchdog at Zephyr system startup for the SoCs that enable
the watchdog by default after reset", and makes this default to y in
order to prevent unintentional processor reset by the watchdog when
not explicitly configured and fed by the application.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Now that all watchdog drivers support DTS we can move setting of
HAS_DTS_WDT to the global watchdog symbol instead of per driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace CONFIG_WDT_0_NAME with DT_ALIAS_WATCHDOG_0_LABEL in samples and
test code. Now that all drivers are DT aware we don't ever set the
Kconfig option.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Such watchdog timer is found on mec1501.
It comes with a support of dbg stall feature and interrupt support.
It does not support multistaging.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Migrate from `SYS_LOG` to `LOG` logging mechanism.
Signed-off-by: Olivier Martin <olivier.martin@proglove.de>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Each driver seemed to use their own Kconfig option to set the name for
their drivers. This makes writing example/test code difficult as each
one of them will have to special case for each of the supported
platforms.
Use a consistent CONFIG_WDT_0_NAME option in all drivers.
Fixes#8094.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
New API enables setting watchdog timeout in the unit of microseconds.
It is possible to configure watchdog timer behavior in CPU sleep state
as well as when it is halted by the debugger.
It supports watchdogs with multiple reload channels.
Jira: ZEP-2564
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Zephyr's watchdog API is badly designed in the sense that it's a 1:1
abstraction on top of whatever Quark D2000 expects for its watchdog,
instead of expecting a generic timeout value.
This implementation tries as much as possible to calculate the watchdog
timeout in a way that's compatible with a Quark D2000 running at 32MHz;
a comment in adjust_timeout() explains this in more detail.
Jira: ZEP-2296
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Basic Watchdog driver for Atmel SAM family MCUs. Currently only
disabling the watchdog is supported.
Tested on Atmel SAMV71 Xplained Ultra Evaluation Kit.
Origin: Original
Jira: ZEP-1684
Change-Id: I8f717c7f53aa290c944b7935e0570c2a6f53956e
Signed-off-by: Souvik K Chakravarty <souvik.k.chakravarty@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add driver for CMSDK (Cortex-M System Design Kit) APB WDOG. This device
uses NMI as interrupt hence it requires Runtime NMI (CONFIG_RUNTIME_NMI)
to be configured in the platform.
Tested with drivers/watchdog sample application.
Jira: ZEP-1300
Change-Id: Ib318047109af81e32060e80d456ef3873fd380ea
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch refactors the main Kconfig file in order to align it with the
Zephyr code style and to make sure that each Kconfig configuration
portion is easily identifiable.
Change-Id: Ib226aaa9a98e9b08a47d9d1c329f18f4f6936620
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The config variable WDT_0_IRQ_PRI is intended to be generic across a
range of watchdog drivers, however it has no default value which means
that if CONFIG_WATCHDOG is enabled, but no driver is provided for a
specific board the the configuration will fail. For now, make
WDT_0_IRQ_PRI depend on the only driver that uses it.
Change-Id: I54708d66ac8fbc2ef657a1ef4510eb5e7a2cff28
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Uses locking in an API and removes a global variable
for improved safety/correctness in the face of concurrent
threads and fibers.
The locking mechanism is by default disabled in the
build. To enable it, the following flag needs to be defined:
CONFIG_WDT_QMSI_API_REENTRANCY
Jira: ZEP-440
Change-Id: Ibcd1501a4af628017b20d7e7ce20b988c8e4e4e2
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ic73783189db57059d2b7f3727e4802e1b2e27931
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
