In a3bea8872b (PR #16352)
_bt_br_channels_area was added to the code but not the
sanitycheck sections whitelist => Add it
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
On SMP systems, currently scheduled threads are not in the run queue
and can't be unconditionally removoed/added.
Fixes#17170
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Remove whitelisting and make the test more generic. This test was only
building on 1 board basically, now with the new filters it builds on 24.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove whitelisting and enable broader testing on all boards with needed
features.
Add pwm to board yaml where it applies.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board uses the sam3 gpio driver. gpio_sam was selected by default
causing a conflict and issues when building for this board.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Not all DTS changes are board specific and we should support overlays
that can be used with multiple boards. For example with a sensor, for
example:
Use this overlay for a sensor:
&arduino_i2c {
bme280@76 {
compatible = "bosch,bme280";
reg = <0x76>;
label = "BME280";
};
};
This will work with any board that has &arduino_i2c defined, but should
also work if you specify the instance directly (&i2c0 or &i2c1).
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove old configurations of boards that do not support networking
natively and very custom and difficult to test.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In c20ff1150f
and 5f19c8160a
(PR #16897)
_bt_settings_area was replaced with _settings_handlers_area
Update sanitycheck sections whitelist accordingly
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Correct the storage type of the thread status pointer
not assuming 32bit pointer and integer size
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
holyiot_yj16019 board uses nRF52832 SoC, which does not have 802.15.4
radio. Therefore, 802.15.4 should not be listed in it's capabilities.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The nRF 802.15.4 radio driver should not include nRF52840 header
directly, but rely on soc.h instead. Otherwise, it will not work with
different SoCs supporting 802.15.4.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Start to monitor Connected and Disconnect events and then start
and stop the echo service according to system connectivity status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It currently only listens to relevant events about network interface to
decide whether raising connected or disconnected event.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The code to sanitize the generated font path by removing bindir
improperly stripped the first character of every argument when --bindir
was not provided, corrupting the command documentation when fonts are
generated manually. Only sanitize if --bindir was provided with
non-empty content.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The size_t type is either compatible with an int on 32-bit target, or
a long on 64-bit targets. It could even be a long even on some 32-bit
targets. Let's use the z qualifier in the printf format to be compatible
with whatever flavor in use.
In case of pointers, let's just use %p with pointers directly and
avoid casts altogether.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>