So we can easily access TCP buffer that is stored
in net_buf.
Change-Id: I37ae728be45ded2fcc74735592d94897c945afbe
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This will remove given amount of data from the fragment list.
Change-Id: I17d809982af0b941f957205688ee61e5ac3c1f08
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is needed because if there are more than one network
interfaces configured, then the second interface will point
to wrong address. Only solution to this issue is to align
the net_if to 32 byte boundary. The issue was seen in qemu
and it is not really known if the issue is present in real
hardware.
Change-Id: I2048c8a9a0aab51f84c15539159410b544f6c9b1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print the link layer header in different color so that the
actual IP payload in packets are easier to see. Also the
link layer header of the first packet was not printed.
Change-Id: I99699d378ae28d6d90c683c646c904c926b7dd06
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that the statisitics compilation can be done even
if some sub-statistics module is not compiled, like IPv6 or
IPv4 statistics.
Change-Id: I1a91acd70569f074d9bb3269f74ee9c6a0ea9cf7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the DEBUG options for the new IP stack still used
the CONFIG_NETWORK_IP_STACK_DEBUG_ prefix.
Change-Id: I8f039ac5e303a7c571a870403ce17d758db540d5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Implementing the primitives for non-slotted CSMA-CA radio protocol
according to section 5.1.1.4 in the 2011 version of the specification.
Slotted version will come when Beacon frame will be supported, thus
getting PAN coordinator info from its superframe.
Change-Id: I0545ed953a3c48e6b8e9cd4082db01ed66ad098b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These will be used by other radio protocol, such as CSMA-CA.
Change-Id: I8b308c0376e5e26ae35fbbb4a0a7f99228fa2529
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It can parse newer version's FCF, but it will generate only 2006 ones.
Change-Id: Ib635cc5840505af891a802da8fc6f3ee95478916
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will use the dedicated UART pipe driver to send/receive IEEE
802.15.4 "radio" frames.
- make
On one console:
- make qemu1
On a second console:
- make qemu2
Note:
net-tools is needed, cloned into net/tools
https://gerrit.zephyrproject.org/r/#/admin/projects/net-tools
Change-Id: I833cd40238b0653bb5b9a9b462fb4d5d2a3504b9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net tools directory is now in net/tools
- fixing the 80 chars line limit
Change-Id: I079880fa3449beffb326369ab23550dcba3ccf20
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
More samples will come. Current one is meant to test ieee802154 with
cc2520 on quark_se_devboard target. Some future sample will show how to
use the Qemu uart pipe fake 802.15.4 radio driver for testing on one
host.
Change-Id: Idea2b16cde091c7da926ca8aa71912fbfd0a3d62
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This driver is used for testing on Qemu where all "radio transmission"
will go through a pipe between 2 Qemus.
Change-Id: I5b4e75de82a98eb730ef9c70b460b4b60c0a60c3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If no IP stack is seleceted, selecting one of the 2 cc2520 driver will
automatically select the relevant stack.
Change-Id: Icca22da190dc790ce6d302e14c45732f902e02ae
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- new stack options are renamed and placed in their respective menus
- new stack Kconfig gets normalized (tabs vs spaces, etc...)
Change-Id: Ia68f6589fed464bbdd76dc0812775684b2f94a58
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- tabs are use to indent, no spaces.
- NET_TCP should be defined as an option, though non-promptable for now
Change-Id: I9c5e55e1ab5c82c906fb5650f5d1539c65de1194
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As option list will grow, it will be saner to put them there instead of
growing the base Kconfig.
Change-Id: I72199d1d452986ed7a08d9bb3d1139f49622ec59
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As option list will grow, it will be saner to put them there instead of
growing the base Kconfig.
Change-Id: I610c47540e4fd6784b70198986813b737a38165c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some old left over, was generating hard to spot errors on some other
places (mostly 'choice' related warnings).
Change-Id: I2ce2b27c8ab2703208a74dd852c0f0a7bcbeaa41
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will be necessary for devices that require to instanciate more than
one network interface.
Change-Id: I01fd4eb220ed63a4fe073614fb2a132cd00c6bc8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add socklen_t addrlen parameter to net_context_bind(),
net_context_sendto() and accept callback.
Currently the address length option is not really mandatory
as we can figure out the length from the address family.
But if we are going to support other protocol address families
it might be needed.
Change-Id: I59206465c3259050c469c5b2150221646a9a08d7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because of printk fixes in master, some of the networking
unit tests will fail in next merge.
Change-Id: I3e28aae72c0c10b402b78c0f406ecb3513b967a7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Or the build will not go through.
Change-Id: I48f5f8661c4100a76e4624ea64d383055327e2a7
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When only the dummy frame format is enabled, some variables are left
unused, causing some warnings.
Change-Id: Ic7bc5560a9fcb573e715c2cc29f308cec5214f64
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
When an IPv6 adress is specified, the port specified in the local
address is ignored.
Change-Id: I1df865c00b9b052e353a9d6fab4bf1152567efd5
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
When running echo-server in the Zephyr device (either a real
device or qemu), set the IPv4 address to be 192.0.2.2. The host
IPv4 address should be set to 192.0.2.1 in this case. This change
is similar to IPv6 address change made earlier (now both IPv4 and
IPv6 addresses on device side end with "2", on host side, with "1").
Change-Id: I639b7be4403b4b2f38f01675d0ef56eaabf0f82c
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The net_if.h is only meant for new IP stack.
Change-Id: I133d576d7c070dd4a2291544bd0b0401bda942b5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adding IP services support entries, documentation enhancements,
testing entries and IPv6 basic support entries.
Change-Id: If443ecaabf6bc8ca92f17eff67da9d9e8f7c797f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier all unit tests are with IPv6 and UDP as next header.
Modified tests with IPv6 only, IPv6 + UDP and IPv6 + IPHC next
headers.
Change-Id: Ie02cecb37e07ceae8a06a0653e2ccdfe0db91239
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We missed that section, so sanitycheck was failing.
Also putting the right section in the relevant array.
Change-Id: I361ffa1707c01f0d3c870a7bc36a86ada66af1d2
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Please collect things to do into this document.
Change-Id: I763cd0e3f6ec6b447b5d9efbebcb56f7b50cecc6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We are not just checking the test build but this time
the tests are also run.
Change-Id: I7b0b24c51dfc2dc58f290cca7a593be431b8077f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When running echo-server in the Zephyr device (either a real
device or qemu), set the IPv6 address to be 2001:db8::2.
The host IPv6 address should be set to 2001:db8::1 in this case.
Change-Id: Ia967cecabece4b06a2f5a12b11c68a9de4aeb2af
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The prj_slip.conf file should be used for qemu-to-host
communication only. It is not usable for testing between
two qemus.
Change-Id: Id06813a1b36f33f585e06df3f29479891ea3d2d8
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the CONFIG_NET_TESTING option should be only enabled
if we have Qemu-to-Qemu communication, clearly tell this
in the Kconfig help for that option.
Change-Id: Id1c65d17fb9859ead767294b2f43dd7b57b007ac
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix the correct location of net-tools project files to
samples/net/README file so that the user can test the
echo-server and echo-client apps using SLIP and Qemu.
Change-Id: Ic34fa6e67da916c63e4f138e1e0def5d7632c80c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
640 bytes seems too short, raising to 800 bytes.
Change-Id: I8c3418787939369e24fe47c23b0558c36f05af2c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Debugging messages in 6lo are enabled as well.
Change-Id: I8fea044216e3c4e60d742ebc7256489832ae09ac
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Only meant to be used while debugging deeply. Thus needs to be enabled
by hand in the source code.
Change-Id: Idf4e33154fee0e3d7e1da64708e1c7b4d790d790
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Packet is compressed after its ll part has been computed when sending.
And it is then decompressed after the ll part has been validated when
receiving.
Change-Id: Ifebbd5727623e94f1c2273f2211ba0f109ac4a8f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Buf ll addr need to point to the right place, depending whether it's a
plain address field (thus with the pan ID) or not.
Change-Id: I9897b1f9bec0f7cecd01517c69c3bdefe2bc204b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
