Also fix typo in debug print when discarding a packet.
Change-Id: I3ac41e86d7b2dc05b9d92cde93a646f2dc49d8c0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
SLIP buffer size depends on maximum IEEE 802.15.4 frame size and start
byte.
Change-Id: I1cb0a848dce6b0c85bf11408733d777f7a3b03c9
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This commit adds the frdm_k64f board to the testcase.ini while list.
It also updates the README file with the build instructions and
firmware version used in this test.
Change-Id: Ia0e989d483aede51aa53e7453bbd1c260223372d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The bitwise and operator was being applied to a boolean operand because
of lack of parenthesis in the expression.
Change-Id: Ibfbdd8acce9db95f9274f48fd145f4d8467508e2
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Origin: Original
Based on "IEEE Std 802.3-2008, Section 2" Chapter 22.2.4
Change-Id: I08516dd1c2f74c1324d00d665f221e01af25d7f1
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Replace NANOKERNEL by POST_KERNEL in the net stack.
Change-Id: Iaad7cdbe849741bc1cf18b0ccf7264417a9495d6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove unneeded SET_HW_ADDR_FILT since it is handled by other
commands and add missing opcodes.
Change-Id: I4b6488e6cee742b79c16789e817795138506dc77
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
IPSP spec states other security level can be used depending on the use
case:
7.1 Node Security Considerations
This section describes the security requirements for the Node.
The Node may use the SM Slave Security Request procedure to request
an LE Security Mode other than LE Security Mode 1 Level 1 if required
by the use case.
Change-Id: I24c6676bdb05099a7e222085ee41539994eea77f
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth driver requires BLUETOOTH_SMP in order to build properly since
BLUETOOTH_L2CAP_DYNAMIC_CHANNEL depend on it.
Change-Id: I7878c0c26ebf688b2a7321eb37025a9ebde6c6b8
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It's 127 by default as soon as 802.15.4 l2 is selected.
Change-Id: I6c29d88bb3277a15fe54693027caf320bc3d9fc4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Thus setting a high priority of 2 on the rx fiber, as 0 is invalid.
Change-Id: I44a95f3648ca3fbf2eb699f1fa36963d6f3e5021
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These cflags were only needed when using the old network stack.
Change-Id: I660e397b2648137450c45d4f2edc8ec6ec7ae774
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This demo showcases how to expose resources that are exposed using the
link-format feature.
Change-Id: Iad9421082fae3212cae58e6d6e9b88fa170678b8
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
RFC6690[1] defines a lightweight format for listing and querying
resources and their relationships.
The RFC defines an '.well-known/core' resource that will list the
resources and their associated metadata. It also allows resources to
filtered by their attributes.
The implementation uses the fact that resources are organized in an
array: only the resources present in the array after the
"ZOAP_WELL_KNOWN_CORE_RESOURCE" will be considered, this allows a
primitive form of visibility control for the attributes.
[1] https://tools.ietf.org/html/rfc6690
Change-Id: I2bc21ddf45f20e1f749d8ac36d247474fdaa9d64
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Add an alternative to zoap_packet_get_payload(), that instead of
returning a byte array, returns the net_buf (with the COAP_MARKER
added, if needed) associated with the packet, positioned so the
application can add more data.
Change-Id: I7c955ef42f5ef8406d77da994d1673e6a69b0b6b
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The functions that return the start of the UDP and TCP buffers,
did not take the IP extension header length into account.
Change-Id: Ie3e2fbc49365de9176a788b54ab628e6ef37f5ee
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
More logical place for net_ipv4_broadcast_address() is in ipv4.c
instead of net_if.c.
Change-Id: I069f5030963bcb809df34e874054e2b7826ff868
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
More logical place for net_ipv6_unspecified_address() is in ipv6.c
instead of net_if.c. Removing the net_if_ipv6_unspecified_addr()
variant as it is no longer needed.
Change-Id: Ib5b4f6748030a8bf50fb848a87eef2968e2bcbc8
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_context_bind() was checking that the IP address is
specified before allowing the binding. If the user wants
to bind to any address, then this check needs to be relaxed
a bit.
Change-Id: Ic92b1ba616bf096551ee996fb9cdbf2c9d156f60
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add function that returns IPv4 any address (all bits are zero).
Change-Id: I8816f7f264ad3a98fced7089f0b94220603c2291
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
6lo compresses and fragments the result. Result is that we might end up
with less fragments than earlier. So it's more logical to create the
15.4 frame _after_ 6lo compression/fragmentation. However, since 6lo
compresses the IPv6 header, it is not possible to use buffer's IPv6
distant address directly. Instead, we copy it locally before 6lo, and
use this copy to generate the 15.4 frames afterwards.
Change-Id: I1c7b1a1702daffd6be4cacd15011c84f0beb4b2f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When 802.15.4 L2 is built-in, let's set the nbuf user data size to 127
to avoid current limitation of nbuf not taking care of MTU by itself (so
it would fragment per-nbuf user data size, and not per-MTU).
Change-Id: I14e7b0df5ae24d5c0474d1f111fac59d795ab292
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of appending the LQI into the buffer, which is an awkward usage.
Change-Id: I2f604cd61ef3b309cdfe304dac0ab1e7a2ca3f6a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the distant link layer address is unknown, let's find it out.
Change-Id: I2c0488bb2a32093d7a3a98b021ad5f6e1b6c0d9a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
And take the opportunity to reduce the buffer size, as 127 is the 15.4
MTU, it has just engouh space on 128 bytes for the spi cmd plus the
frame.
Change-Id: Ifdeb83f85ab1adcdebc55bd72c38a98f18a86dbc
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We need to make sure that the link layer size is correctly set
depending on destination address. This is mandatory in IEEE
802.15.4 which has dynamic link layer header size depending on
the IPv6 distant address, which obviously might become
available in net_context_sendto() after the buffer has been
filled in with data.
If we need to adjust the ll header length, we need to copy
the data from the old fragments to the new ones.
This takes into account fact that ll header size might be
bigger or smaller than previous reserve space.
Change-Id: I70edc55d41bee848837dda9b8a76f13985acc281
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Current value (100) is outside the default values: 0 - 15.
Jira: ZEP-1231
Change-Id: Ib3120b52e6eb3d95b369debd7df541fa2b0dfa6e
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Forcefully set the IPv6 address in echo-client so that we
can use that address when sending data. Normally this should
not be done like this as the system should autoconfigure itself.
Change-Id: Id24f9aa84b30a3da941bb6b9e4522c7218687e12
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we have received IPv6 or IPv4 packet where destination
address is a multicast one, and if there is no connection
listener for that address, then do not send ICMP destination
unreachable port error to peer.
Change-Id: I63ae5c72cf4bb75836a62670754e0b95484a6ed8
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If net_send_data() returns 0, then the buffer was sent ok
and the sending device driver has already freed the buffer.
If net_send_data() returns <0, then the buffer sending failed
and the caller can either try to fix the issue and re-send the
buffer, or the caller can unref the buffer. Normally caller
should unref the buffer in this case as there is not much that
can be done here.
Change-Id: I39d7b22bbb78a9c16fd037f3a066797e455c31fd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The pos and len variables were in incorrect order.
The pos is first before the len variable.
Change-Id: I0b078ce2f08923c1673bd918fc03adb2ff09691a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds support for the MQTT protocol v3.1.1.
Specifically, this commit allows a Zephyr application to create
the following MQTT messages:
CONNACK, CONNECT, PUBLISH, PUBACK, PUBREC, PUBREL, PUBCOMP, UNSUBACK,
SUBSCRIBE, SUBACK, UNSUBSCRIBE, PINGREQ, PINGRESP, and DISCONNECT.
Furthermore, the following messages can be parsed by the routines
provided by this commit:
CONNACK, CONNECT, PUBLISH, PUBACK, PUBREC, PUBREL, PUBCOMP, UNSUBACK,
SUBSCRIBE, SUBACK, PINGREQ, PINGRESP and DISCONNECT.
NOTE: client behavior (routines with network access) and QoS will be
integrated in future patches.
The MQTT v3.1.1 specification can be found at:
http://docs.oasis-open.org/mqtt/mqtt/v3.1.1/mqtt-v3.1.1.html
Origin: Original
Jira: ZEP-365
Jira: ZEP-591
Jira: ZEP-856
Change-Id: Ie0c179370cea22f7554564692bc426a8d5c419d2
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
