We have been passing around options from one function to the next making
it very difficult to add a new option easily and requiring changes to
man function prototypes.
This declated the parsed command line options global and renames args to
options. args is being used elsewhere and this was confusing.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board doesn't support `make flash` way of programming.
So, remove that from documentation.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
I don't know why we have been passing "-serial none" to qemu but it
does not seem to be doing anything useful. So I propose we remove it.
According to the qemu documenation it should be disabling all serial
ports;
"-serial dev
Redirect the virtual serial port to host character device dev. The
default device is vc in graphical mode and stdio in non graphical
mode.
This option can be used several times to simulate up to 4 serial
ports.
Use -serial none to disable all serial ports."
But when we use "-serial none", we always combine it with "-serial
pipe", or "-serial unix", to redirect the serial port, so clearly it
is not disabling all serial ports as it attempting to do.
"-serial none" was first introduced to Zephyr in this commit:
0b54f984b8
As far I can tell, pinging an echo_server works fine without it, so I
suspect that our second -serial flag is overriding it and that it has
no effect.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This updates GAP, GATT, SM, L2CAP ICS values according to following
documents:
GAP.ICS.5.0.2
SM.ICS.5.0.0
GATT.ICS.5.0.1
L2CAP.ICS.5.0.1
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Do not reset net_context information in net_app_close. In case of
TCP behind the curtains connection might wait for some timers to
expire and send some messages (e.g. ACK). If we set source port to
'0', unexpected behaviour might happen with peer connection.
Only reset net_app context related information on net_app_close.
Let net_context_put will take care of proper connection closure.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Right now in FIN_WAIT1 state, if we receive FIN+ACK message, then
tcp state changed to FIN_WAIT2 on ACK flag and immediately on FIN
flag state changed to TIME_WAIT. Then final ACK is prepared and sent
(in queue at-least) to peer. Again immediately state changed to
TCP_CLOSED, where context is freed. net_context_put frees context
and releases tcp connection. Final ACK packet which is in queue
is dropped.
As a side effect of freed ACK packet, peer device keep on sending
FIN+ACK messages (that's why we see a lot of "TCP spurious
retransimission" messages in wireshark). As a result
of context free (respective connection handler also removed), we see
lot of packets dropped at connection input handler and replying with
ICMP error messages (destination unreachable).
To fix this issue, timewait timer support is required. When tcp
connection state changed to TIMEWAIT state, it should wait until
TIMEWAIT_TIMETOUT before changing state to TCP_CLOSED. It's
appropriate to close the tcp connection after timewait timer expiry.
Note: Right now timeout value is constant (250ms). But it should
be 2 * MSL (Maximum segment lifetime).
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
fin_timer will be started after sending FIN to peer. After successful
reception of FIN+ACK message in FIN_WAIT1 state, fin_timer should be
cancelled.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Using the '\$' technique to accept make variables corrupts Ninja build
systems, so avoid using it when generating Ninja files. Not using it
with Ninja means we need to come up with some other mechanism to
support build-time configuration of the QEMU CLI with Ninja.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add implementation to consider differing Rx chain delays for
S2 and S8 Coded PHY PDU reception. These changes are
required to meet tIFS timings for transmission after a
reception on S8 coding.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove build_only and add harness type needed for the sample/test to
allow running with sanitycheck and on devices once we have harness
support.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Still need a better way to filter and a better way to support multiple
platforms with these tests, but for now we remove the build_only tag and
make it depend on real HW.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
